Hoshizaki KM-1400SWH/3-M instruction manual Cleaning Procedure

Page 20

1.Cleaning Procedure

1)Dilute 27 fl. oz. (800 ml) of Hoshizaki "Scale Away" with 5 gal. (19 l) of warm water.

2)Remove all ice from the evaporator and the storage bin.

Note: To remove cubes on the evaporator, turn off the power supply and turn it back on after 3 minutes. The harvest cycle starts and the cubes will be removed from the evaporator.

3)Turn off the power supply.

4)Remove the front panel, then remove the insulation panel by first removing the thumbscrew, lifting up the panel slightly and pulling it towards you.

5)Remove the drain plug located on the lower front part of the ice chute. Allow the water tank to drain.

6)Replace the drain plug in its correct position. Be careful not to cross thread it.

7)In bad or severe water conditions, clean the float switch assembly as described below. Otherwise, continue to step 8.

a.Disconnect the vent tube and the flush tube from the top of the float switch, then remove the float switch assembly. Remove the rubber boot from the bottom of the assembly.

b.Remove the retainer rod from the bottom of the float switch housing, then remove the float. Be careful not to bend the retainer rod excessively when removing it.

c.Wipe down the float switch assembly's housing, shaft, float, and retainer rod with cleaning solution. Clean the inside of the rubber boot and hose with cleaning solution. Rinse the parts thoroughly with clean water.

d.Reassemble the float switch assembly and replace it and the rubber boot in their correct positions. Reconnect the vent tube and the flush tube.

8)Pour the cleaning solution into the water tank.

9)Fully open the cleaning valve on the left side wall of the machine compartment.

10)Move the control switch on the control box to the "WASH" position.

11)Replace the insulation panel and the front panel in their correct positions.

12)Turn on the power supply to start the washing process.

13)Turn off the power supply after 30 minutes.

14)Remove the front panel and the insulation panel.

15)Remove the drain plug. Allow the water tank to drain. Replace the drain plug and the insulation panel in their correct positions.

16)Move the control switch to the "ICE" position.

17)Close the cleaning valve.

Note: The icemaker will not operate unless the cleaning valve is completely closed.

18)Replace the front panel in its correct position.

19)Turn on the power supply to fill the water tank with water.

20)Turn off the power supply after 3 minutes.

21)Remove the front panel and fully open the cleaning valve.

20

Image 20
Contents Modular Crescent Cuber Models KM-1400SWH/3-M Hoshizaki AMERICA, INC Contents Important Safety Information Serious injuryIndicates important information about the use and care UnitSpecifications Nameplate Rating KM-1400SWH-M water-cooled marineKM-1400SWH3-M water-cooled marine Dimensions/Connections KM-1400SWH/3-M water-cooled marineII. Installation and Operating Instructions Checks Before InstallationHow to Remove Panels See FigSetup LocationThermostat Extension Bracket stainless Installation of Second Unit Page KM-1400SWH3-M Electrical ConnectionKM-1400SWH-M Icemaker Water Supply and Drain ConnectionsSee or Water-Cooled Condenser Connection to an Open Drain SystemConnection to a Closed Loop System Final Checklist Startup III. Cleaning and Maintenance Cleaning & Sanitizing InstructionsCleaning Procedure Sanitizing Procedure Following Cleaning Procedure Maintenance Preparing the Icemaker for Long StorageStainless Steel Exterior Storage Bin and ScoopDrain the water tank Remove the water from the water-cooled condenserHoshizaki AMERICA, INC

KM-1400SWH/3-M specifications

The Hoshizaki KM-1400SWH/3-M is a state-of-the-art ice maker designed for high-capacity ice production, catering to the needs of busy commercial establishments such as restaurants, bars, and hotels. Known for its robust construction and innovative technologies, this model stands out in the realm of ice-making equipment.

One of the main features of the KM-1400SWH/3-M is its impressive ice production capacity. It can generate up to 1,400 pounds of crescent ice daily, ensuring that businesses can efficiently meet their ice needs, even during peak hours. The crescent ice produced is not only aesthetically pleasing but also melts slowly, making it ideal for drinks and food preservation.

The KM-1400SWH/3-M utilizes Hoshizaki’s advanced refrigeration technology, which includes a stainless steel evaporator that enhances durability and ensures optimal performance. This model is designed for energy efficiency, often exceeding ENERGY STAR requirements. It features a highly efficient compressor and insulation that minimize energy consumption while maximizing ice production.

Another remarkable characteristic of this ice maker is its user-friendly interface, which simplifies operation and maintenance. The machine includes a built-in control panel that allows easy monitoring of functions and diagnostics. Additionally, the ice maker’s vertical evaporator design reduces the size of the unit while increasing ice production efficiency, making it suitable for tight spaces.

Hoshizaki prioritizes hygiene and ease of maintenance. The KM-1400SWH/3-M has a removable air filter and an automated cleaning cycle that helps maintain optimal sanitary conditions, significantly reducing the frequency of manual cleaning. The antimicrobial surface also aids in preventing bacterial growth, promoting a healthier environment.

In terms of adaptability, the Hoshizaki KM-1400SWH/3-M can work seamlessly with various water conditions, making it a versatile choice for different setups. It operates well in both high and low ambient temperatures, providing consistent ice production regardless of external factors.

Overall, the Hoshizaki KM-1400SWH/3-M is a reliable, high-capacity ice maker that combines modern technology, energy efficiency, and user-friendly features. Its durable construction and innovative design make it an excellent choice for any commercial operation requiring a steady supply of high-quality ice.