Manitowoc Ice S1400M manual Before Calling For Service Section, Safety Limit Feature

Page 36

Before Calling For Service

Section 5

 

 

Problem

Possible Cause

To Correct

Ice machine produces shallow or

Ice thickness probe is out of adjustment.

Adjust the ice thickness probe.

incomplete cubes, or the ice fill pattern on

 

(See Section 4)

the evaporator is incomplete.

 

 

Water trough level is too low.

Check the water level probe for damage.

 

 

(See Section 3)

 

Water inlet valve filter screen is dirty.

Remove the water inlet valve and clean

 

 

the filter screen. (See Section 4)

 

Water filtration is poor.

Replace the filter.

 

Hot incoming water.

Connect the ice machine to a cold water

 

 

supply. (See Section 2)

 

Water inlet valve is not working.

Replace the water inlet valve.

 

Incorrect incoming water pressure.

Water pressure must be 20-80 psi

 

 

(1.4 bar - 5.5 bar)

 

Ice machine is not level.

Level the ice machine.

 

 

(See Section 2)

Low ice capacity.

Water inlet valve filter screen is dirty.

Remove the water inlet valve and clean

 

 

the filter screen. (See Section 4)

 

Incoming water supply is shut off.

Open the water service valve.

 

Water inlet valve stuck open or leaking.

Place toggle switch in OFF position, if

 

 

water continues to enter water trough

 

 

replace the water inlet valve.

 

The harvest assist air compressor is not

Call for service.

 

functioning.

 

Safety Limit Feature

In addition to the standard safety controls, such as the high pressure cutout, your Manitowoc ice machine features built-in safety limits which will stop the ice machine if conditions arise which could cause a major component failure.

Before calling for service, re-start the ice machine using the following procedure:

1.Move the ICE/OFF/CLEAN switch to OFF and then back to ICE.

A.If the safety limit feature has stopped the ice machine, it will restart after a short delay. Proceed to step 2.

B.If the ice machine does not restart, see “Ice machine does not operate” on the previous page.

2.Allow the ice machine to run to determine if the condition is recurring.

A.If the ice machine stops again, the condition has recurred. Call for service.

B.If the ice machine continues to run, the condition has corrected itself. Allow the ice machine to continue running.

5-2

Part Number 80-1631-3

Page 35 Page 37
Image 36
Page 35 Page 37
Contents S1400M Model Ice Machines Installation Use and Care Manual Read These Before Proceeding Personal Injury PotentialTable of Contents Table of Contents Section MaintenanceSection Before Calling For Service Section Ice Machine OperationHow to Read a Model Number Section General InformationModel Numbers Ice Cube SizesGeneral Information Section Accessories Section General Information Model/Serial Number Location Model/Serial Number LocationWarranty Coverage Section Installation Instructions Ice Machine DimensionsGeneral S1400M WATER-COOLED ICE MachinesInstallation Instructions Section Location of Ice Machine Ice Machine Heat of RejectionSection Installation Instructions Electrical Service VoltageMinimum Circuit Ampacity Electrical RequirementsFor United Kingdom Only Self Contained ICE Machine 115/1/60 or 208-230/1/60Self Contained ICE Machine 208-230/3/60 Self Contained ICE Machine 230/1/50Cooling Tower Applications Water SupplyWater Inlet Lines Drain ConnectionsInstallation Instructions Section Typical Water Supply Drain InstallationWater Supply and Drain Line SIZING/CONNECTIONS Section Installation Instructions Installation Check List AuCS Automatic Cleaning System Potential Personal Injury SituationSection Ice Machine Operation Component IdentificationIce Machine Operation Section Sequence Of Operation Initial START-UP or START-UP After Automatic SHUT-OFFSafety Timers Harvest Sequence 5. Water PurgeHarvest Automatic SHUT-OFF 7. Automatic Shut-OffIce Machine Operation Section Operational Checks Water LevelICE Thickness Check Ice Thickness CheckWater Purge Adjustment Harvest Sequence Water PurgeIce Machine Operation Section Section Maintenance Exterior CleaningIce Machine Inspection Water-Cooled Condenser Water Regulating ValveMaintenance Section Guardian InstallationSachet Replacement Frequency Sachet Replacement ProcedureSection Maintenance Interior Cleaning and Sanitizing Cleaning ProcedureStep Maintenance Section Sanitizing ProcedureRemoval of Parts for CLEANING/SANITIZING Water Curtain Water Curtain Removal Ice Thickness ProbeIce Thickness Probe Removal Water Distribution Tube Water TroughWater Distribution Tube Removal Water Level Probe Water PumpWater Pump Removal Dump Valve Disassembly Water Dump ValveEvaporator Tray Removal Drain Line Check ValveWater Inlet Valve Maintenance Section Removal from Service/Winterization Pry Open the Water Regulating Valve AUCS→ AccessorySELF-CONTAINED WATER-COOLED ICE Machines Section Before Calling For Service ChecklistBefore Calling For Service Section Safety Limit FeaturePage Manitowoc ICE, INC

S1400M specifications

The Manitowoc Ice S1400M is a cutting-edge ice machine designed for high volume ice production, widely popular in the restaurant and hospitality industries. This model is part of Manitowoc’s acclaimed line of ice machines, known for their durability, efficiency, and innovative features that simplify ice making while enhancing operational performance.

One of the most notable features of the S1400M is its impressive production capacity. This unit is capable of producing up to 1,400 pounds of ice per day, making it a reliable choice for businesses with high ice demands. Whether it's for cocktails, beverages, or food preservation, the S1400M ensures that there is always enough ice available to meet customer needs.

The S1400M employs Manitowoc's advanced ice-making technology, which includes a state-of-the-art 100% stainless steel evaporator. This not only enhances the longevity of the unit but also helps produce cleaner and clearer ice. The unit utilizes a patented built-in actuator that completely purges the evaporator during the harvest cycle, ensuring that the ice is free from contaminants and undesirable residues.

Furthermore, the Manitowoc S1400M is designed with energy efficiency in mind. It operates with the Energy Star certification, which means it meets strict energy efficiency guidelines set by the U.S. Environmental Protection Agency. This reduces operational costs and environmental impact, making the S1400M an excellent investment for eco-conscious businesses.

This model is also equipped with an intuitive ice thickness control system, allowing for customization of ice size according to specific needs. Users can easily set the machine to produce either half-cube or full-cube ice, catering to varying beverage requirements. Additionally, the S1400M features a user-friendly interface and digital display, providing operators with real-time machine status updates and alerts for maintenance or service needs.

Another important aspect of the S1400M is its flexible installation options. This unit can be paired with a variety of bins and dispensers, allowing businesses to optimize their space while ensuring the functionality of their ice supply. Its compact design is ideal for establishments with limited space, making it a versatile choice for bars, restaurants, and hotels.

In summary, the Manitowoc Ice S1400M represents the perfect blend of power, efficiency, and technological advancement. With its high production capacity, durable construction, customizable ice production, and energy-saving features, the S1400M stands out as a leading choice for any business requiring consistent and high-quality ice.
Top Page Image Contents