Jackson CREW 66S, CREW 44S manual Ventilation Duct CONN. Unload END 4x 16ID

Technical Manual (07610‐003‐78‐18)

MACHINE DIMENSIONS ( 44” Right to Left)

	in		in
	8		4 in
	7	1		8
	7		2	3
	in				W	E2				in	in
							E1			2
1	14			RA						21	14
in	8									1
	7			SAN					4 in
8
19									in	in
							D		16	8		2
										26	2
										5	in	in
											1	1
											16	30
					TABLE to TABLE				43 8 in	S*
						44 in
						633 8 in		515		C*
									8 in
					235 8 in
				V2				(NOTE 2)		V1
	in			2118 in
	8			1
	3			11 8 in
	7			414 in
								E1
						E2
					W
				RA
in				SAN							in
2											8
1										5
64											71
in
8
5
63										in
	in									2
										1
	1									67
	8
	61								DET
	in			DET	CP				S*	in
						D		C*
	4									4
	3									3
	23									23
										in
			in							4
			2						9in	1
			11							15
	1
(NOTE 4)				1		in		618 in		(NOTE 4)
	1					3		1412 in
						4				43 8 in
(NOTE 3) 10 8 in				11 2 in		8
						4418 in

NOTE 1:

THE MAXIMUM DOOR HEIGHT MAY BE REDUCED BY THE ADDITION OF OPTIONAL DOOR BRACKETS. MAXIMUM HEIGHTS OF 91", 89" & 87" ARE AVAILABLE.

NOTE 2:

VENTILATION DUCT ADAPTERS ARE

ADJUSTABLE FROM 51-1/2" TO 54".

NOTE 3:

THE DRIVE ASSEMBLY AND GUARD MAY BE INSTALLED ON EITHER END OF THE UNIT. INSTALLATION ON THE UNLOAD END IS STANDARD. IF INSTALLED ON THE LOAD END, PLEASE ENSURE ANY SCRAP SINKS IN THE TABLING ARE AT AN ADEQUATE DISTANCE TO PROVIDE FOR CLEARANCE OF THE DRIVE ASSEMBLY.

NOTE 4:

ALL VERTICAL DIMENSIONS MAY

VARY DUE TO THE ADJUSTABLE

FEET.

					E1
					E2
					W
93 in MAX (NOTE 1)	205 8 in
		20 in
					DET
34 in					in
					4
					3
					23
S*	CP
(NOTE 4)		33	4	in	(NOTE 4)
	1
	17	8 in

*APPLIES TO STEAM HEATED UNITS

**CHEMICAL SANITIZING UNITS ONLY

E1	MAIN ELECTRICAL CONNECTION (1.375” DIA HOLE)
E2	BOOSTER HEATER ELECT. CONNECTION (1.375” DIA)
W	MAIN INLET WATER CONNECTION (1/2 NPT‐F )
D	DRAIN CONNECTION ( 1‐1/2” NPT‐F)
DET	DETERGENT BULKHEAD ACCESS (.875” DIA HOLE)
SAN**	SANITIZER INLET TO RINSE (1/8” NPT‐F)

RA	RINSE AID CONNECTION TO RINSE (1/8” NPT‐F)
CP	CONDUCTIVITY PROBE ACCESS (.875” DIA HOLE)
S*	STEAM TO WASH TUB HEATING COIL (3/4” NPT‐F)
C*	CONDENSATE RETURN (3/4” NPT‐F)
V1	VENTILATION DUCT CONN. (LOAD END) 4” x 16” ID
V2	VENTILATION DUCT CONN. (UNLOAD END) 4”x 16”ID

Page Created: 06‐30‐2011

Revised: N/A

7