Jackson CREW 66S, CREW 44S manual PRE‐WASH Inlet Water Conn /2 NPT‐F

		Technical Manual (07610‐003‐78‐18)
		MACHINE DIMENSION (66” Left to Right)
																				in	in
																				8 4 in
																				3	2	9
																					1
NOTE 1:
THE MAXIMUM DOOR HEIGHT MAY BE
REDUCED BY THE ADDITION OF OPTIONAL					in								E2	W1	RA							in
DOOR BRACKETS. MAXIMUM HEIGHTS OF		in
					8																	8
91", 89" & 87" ARE AVAILABLE.					7			W3***				W2	E1									7	in
ADJUSTABLE FROM 73-1/2" TO 76".		14	16in		14												SAN**					14	20	1	in
NOTE 2:																							8
VENTILATION DUCT ADAPTERS ARE																						3		in
																								2
NOTE 3:					4 in																			21	8
	in	in								D2			D1												5
THE DRIVE ASSEMBLY AND GUARD	8	8																							26
MAY BE INSTALLED ON EITHER END	5	5
OF THE UNIT. INSTALLATION ON THE
	30	16
UNLOAD END IS STANDARD. IF
INSTALLED ON THE LOAD END,
PLEASE ENSURE ANY SCRAP SINKS																						S*
IN THE TABLING ARE AT AN ADEQUATE												TABLE to TABLE
DISTANCE TO PROVIDE FOR CLEARANCE
OF THE DRIVE ASSEMBLY.												8512 in	66 in
NOTE 4:																						C*
ALL VERTICAL DIMENSIONS MAY
VARY DUE TO THE ADJUSTABLE										7312 in MIN
FEET.														2312 in
		V1								(NOTE 2)											V2
															21 in
					107												1118 in
E1						8	in									1
															4		4 in
E2
											W2		E1									in
W1													E2													in
								W3***														8
													W1									3				8
	in93MAX (NOTE1)																					7			5
205 8 in 20in														RA											67	71
																SAN**									in
																									2
																								1
																								in
																								2
		2																					in	1
																								64
		in
DET	1																						8
		63 in																				in	5
																		DET					63
		61
												D2										8
																	S*					1
		in											CP									61
														C*
in		34											D1
4																						in
3			2
23																						1
			in																			4
			11																		in9 15
			1
CP
33 4 in	(NOTE 4)	(NOTE 4)		in				75	8	in					61	8	in			in		(NOTE 4)
1										1		in					1		in
				4					33		2				14			2		4
17 8 in			3										6618 in							3		1018 in (NOTE 3)
				8																8

*APPLIES TO STEAM HEATED UNITS

**CHEMICAL SANITIZING UNITS ONLY

***PRE-WASH COLD WATER THERMOSTAT OPTION ONLY

E1	MAIN ELECTRICAL CONNECTION (1.375” DIA HOLE)
E2	BOOSTER HEATER ELECT. CONNECTION (1.375” DIA)
W1	MAIN INLET WATER CONNECTION (1/2 NPT‐F )
W2	PRE‐WASH INLET WATER CONN. (1/2 NPT‐F)
W3***	PRE‐WASH COLD WATER CONN. (1/2 NPT‐F)
D1	DRAIN CONNECTION, WASH ( 1‐1/2” NPT‐F)
D2	DRAIN CONNECTION, PRE‐WASH ( 1‐1/2” NPT‐F)
DET	DETERGENT BULKHEAD ACCESS (.875” DIA HOLE)

SAN**	SANITIZER INLET TO RINSE (1/8” NPT‐F)
RA	RINSE AID CONNECTION TO RINSE (1/8” NPT‐F)
CP	CONDUCTIVITY PROBE ACCESS (.875” DIA HOLE)
S*	STEAM TO WASH TUB HEATING COIL (3/4” NPT‐F)
C*	CONDENSATE RETURN (3/4” NPT‐F)
V1	VENTILATION DUCT CONN. (LOAD END) 4” x 16” ID
V2	VENTILATION DUCT CONN. (UNLOAD END) 4”x 16”ID

Page Created: 06‐30‐2011

Revised: N/A

8