INSTALLATION/OPERATION Instructions | Jackson AJ-66TE, AJ-80TE

SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

NOTE: THE INSTRUCTIONS PROVIDED HEREIN, UNLESS OTHERWISE SPECIFIED ARE FOR THE DISHMA- CHINES ONLY. THERE ARE SEPARATE DIRECTIONS FOR THE GAS BOOSTER.

VISUAL INSPECTION: Before installing the unit, check the container and machine for damage. A damaged container is an indi- cator that there may be some damage to the machine. If there is damage to both the container and machine, do not throw away the container. The dishmachine has been inspected and packed at the factory and is expected to arrive to you in new, undam- aged condition. However, rough handling by carriers or others may result in damage to the unit while in transit. If such a situ- ation occurs, do not return the unit to Jackson; instead, contact the carrier and ask them to send a representative to the site to inspect the damage to the unit and to complete an inspection report. You must contact the carrier within 48 hours of receiving the machine. Also, contact the dealer through which you purchased the unit.

UNPACKING THE DISHMACHINE: The machine should be unboxed and removed from shipping pallet prior to being installed. Open the front door and remove all of the packing materials. Once unpacked, ensure that there are no missing parts from the machine. This may not be obvious at first. If it is discovered that an item is missing, contact Jackson immediately.

LEVEL THE DISHMACHINE: The dishmachine is designed to operate while being level. This is important to prevent any damage to the machine during operation and to ensure the best results when washing ware. The unit comes with adjustable bullet feet, which can be turned using a pair of channel locks or by hand if the unit can be raised safely. Ensure that the unit is level from side to side and from front to back before making any connections. You will be able to adjust the over- all height of the unit by turning the bullet feet from between 75-1/2” to 76-1/2”.

PLUMBING THE DISHMACHINE: All plumbing connections must comply with all applicable local,

state, and national plumbing codes. The plumber is responsible for ensuring that the incoming water line is thoroughly flushed prior to connecting it to any component of the dishmachine. It is necessary to remove all foreign debris from the water line that may potentially get trapped in the valves or cause an obstruction. Any valves that are fouled as a result of foreign matter left in the water line, and any expenses resulting from this fouling, are not the responsibility of the manufacturer.

Water hardness should be a maximum of 6 grains per gallon. Harder water should be treated prior to using the machine. Iron in the water supply can cause staining. A filter designed to remove iron from the supply water is highly recommended for sup- plies in excess of 0.1 ppm (parts per million).

CONNECTING THE DRAIN LINE: The drain for the models covered in this manual are gravity discharge drains. All piping from the machine to the drain must be a minimum 1 1/2” NPT and shall not be reduced. There must also be an air gap between the machine drain line and the floor sink or drain. If a grease trap is required by code, it should have a flow capacity of 30 gallons per minute.

WATER SUPPLY CONNECTION: Ensure that you have read the section enti- tled “PLUMBING THE DISHMACHINE” above before proceeding. The supply water temperature must meet the minimum requirements listed on the machine data plate. Install the water supply line (1/2” pipe size minimum) to the dishma- chine line strainer. It is recommended that a water shut-off valve be installed in the water line between the main supply and the machine to allow access for ser- vice. The water supply line is to be capable of 25 PSI “flow” pressure at the rec- ommended temperature indicated on the data plate.

Adjusting screw

Locking nut

Incoming Plumbing Connection

If the water level is too low or too high, check the incoming water pressure. It should be 20 ± 5 PSI. Too high of pressure results in too much water; too low of pressure results in too little water. To adust the regulator, loosen the nut at the top, this will allow you to screw or unscrew the adjustment. With a screwdriver, turn the adjuster clockwise to increase pressure or counter clock- wise to decrease it.

Do not confuse static pressure with flow pressure. Static pressure is the line pressure in a “no flow” condition (all valves and services are closed). Flow pressure is the pressure in the fill line when the fill valve is opened during the cycle.

It is also recommended that a shock absorber (not supplied) be installed in the incoming water line. This prevents line hammer (hydraulic shock), induced by the solenoid valve as it operates, from causing damage to the equipment.

AJ-44T Series Technical Manual 7610-003-07-21

Issued: 03-21-2006 Revised: N/A

AJ-66TS, AJ-44TG, AJ-66TG, AJ-44TS, AJ-80TS specifications

The Jackson AJ series is well-known for its robust design and reliable performance in the realm of advanced air-jet weaving technologies. Among the various models, the AJ-80TE, AJ-44TE, AJ-66TE, AJ-80TS, and AJ-44TS stand out for their unique features, cutting-edge technologies, and versatility in textile production.

The AJ-80TE is designed for high-speed and efficient weaving, making it ideal for modern textile manufacturing. It offers an impressive production capacity while maintaining a high level of precision. This model incorporates a high-performance air-jet system that ensures quick replenishment of the weft yarn, significantly reducing downtime during production. With a robust construction, the AJ-80TE can handle a wide variety of fabrics, including heavier materials, ensuring adaptability and durability.

Similarly, the AJ-44TE model showcases advanced weaving capabilities with an emphasis on versatility. It is engineered to produce a broad range of textiles, from lightweight fabrics to more substantial materials. The innovative air-jet technology utilized in the AJ-44TE allows for smooth operation and enhanced fabric quality. Its user-friendly interface simplifies the setup process, enabling operators to switch between different fabric types with minimal effort.

The AJ-66TE model presents additional advancements, featuring a sophisticated control system that optimizes weaving patterns. This model is particularly noted for its precision in producing intricate designs, making it a perfect choice for high-end textile applications. Its energy-efficient design also contributes to lower operational costs, aligning with the industry's increasing focus on sustainable production practices.

Moving on to the AJ-80TS and AJ-44TS models, these machines integrate state-of-the-art technologies that enhance user experience and operational efficiency. Equipped with advanced sensors and automation features, these machines can monitor weaving conditions in real-time, ensuring consistent quality and minimizing fabric defects. The AJ-80TS is specifically tailored for larger production runs, while the AJ-44TS excels in versatility, accommodating a wide range of fabric specifications.

In summary, the Jackson AJ series, comprising the AJ-80TE, AJ-44TE, AJ-66TE, AJ-80TS, and AJ-44TS, represents the forefront of air-jet weaving technology. Their combination of robustness, versatility, and cutting-edge features makes them indispensable in modern textile manufacturing, fulfilling the demands for both efficiency and high-quality output. As the industry continues to evolve, these machines stand ready to meet new challenges, empowering manufacturers to push the boundaries of textile innovation.