Garmin 210 GEO T DL user manual Positioning the Cooker, These are not supplied by with the cooker

Page 21

You will need the following equipment to complete the cooker installation satisfactorily

STABILITY BRACKET

If the cooker is to be supplied with gas through a flexible hose, a stability bracket or chain must be fitted.

These are not supplied by with the cooker

but are available at most builders’ merchants.

GAS PRESSURE TESTER

FLEXIBLE GAS HOSE

Must be in accordance with the relevant standards.

MULTIMETER

(for electrical checks)

You will also need the following tools:

1.Electric drill

2.Masonry drill bit (only required if fitting the cooker on a stone or concrete floor)

3.Rawlplugs (only required if fitting the cooker on a stone or concrete floor)

4.Steel tape measure

5.Cross head screwdriver

6.Flat head screwdriver

7.4mm & 3mm Allen keys

8.Spirit level

9.Pencil

10.Adjustable spanner

11.Screws for fittingstability bracket

Positioning the Cooker

The diagrams show the minimum recommended distance from the cooker to nearby surfaces.

The cooker should not be placed on a base.

*door opening width

The hotplate surround should be level with, or above, any adjacent work surface. Above hotplate level a gap of 75mm should be left between each side of the cooker and any adjacent vertical surface.

For non-combustible surfaces (such as unpainted metal or ceramic tiles) this can be reduced to 25mm.

A minimum space of 800mm is required between the top of the hotplate and a horizontal combustible surface.

Any cooker hood should be installed in accordance with the hood manufacturer’s instructions.

Surfaces of furniture and walls at the sides and rear of the appliance should be heat, splash and steam resistant. Certain types of vinyl or laminate kitchen furniture are particularly prone to heat damage and discolouration. We cannot accept responsibility for damage caused by normal use of the cooker to any material that de-laminates or discolours at temperatures less than 65°C above room temperature.

For safety reasons curtains must not be fitted immediately behind the cooker.

We recommend a gap of 910mm between units to allow for moving the cooker. If a flush fit is required, fit the cooker up to the unit at one side then fit the unit the other side. Do not box the cooker in; it must still be possible to move the cooker in and out for cleaning and servicing.

A clearance of 130mm is required if the cooker is near a corner of the kitchen to allow the oven doors to open.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents User’s Manual Installation and Servicing InstructionsBe safe InstallationGas and Electricity on Peculiar smellsContents Hotplate Burners Wok Cooking Wok Centre RingGlide Out Grill Using the GrillTime minutes Grill Cooking ChartOvens Left Hand OvenRight Hand Tall Oven Multi-function oven functions Base heat Browning elementBoth Ovens SteamTall oven shelves Main Oven shelvesFalcon Multi-function Oven cooking guide Cooking chart Fan assisted oven functionEnsure meat and poultry is fully cooked before serving Oven Shelf Food Temp Position Approximate Cooking TimeOven Cooking chart Conventional and full Fan oven functions Approximate Cooking TimePosition Stainless Steel Hob Cleaning your cookerHotplate burners Glide-OutGrillCleaning Brass Components Control Panel and Oven DoorsMain Oven Tall Oven Moving your cookerTroubleshooting General Safety Instructions If you smell gas0800 111 Take care that no water seeps into the appliance Dear Installer InstallationProvision of Ventilation Location of CookerPositioning the Cooker These are not supplied by with the cookerYou will also need the following tools Moving the Cooker Unpacking the CookerConversion to LP LevellingGas Connection Electrical Connection Main Door adjustmentHotplate GrillServicing warning Conversion to LP GasInjectors To convert the control tapsNatural Gas at 20mbar ReassemblyLP Gas Butane at 28-30 or Propane at 37mbar Burner ringsStick on label Pressure TestingOuter Burners Check the appliance is gas soundServicing To Replace a Grill Controller To Change an Ignition SwitchTo Remove an Oven Cut-Off Thermostat To Remove a Hotplate BurnerTo Remove the Door Latch To Remove the Oven Outer Door PanelTo Remove the Oven Door Seal To Remove the Hotplate Spark GeneratorTo Remove an Oven fan Element To Adjust the Main Oven Door AngleTo Remove the LH Oven Bottom and Top Elements To Remove a Grill ElementKey Circuit DiagramDimensions Technical DataRatings ElectricPage Page ArtNo.000-0001 Aga address block

210 GEO T DL specifications

The Garmin 210 GEO T DL is an advanced GPS device designed for outdoor enthusiasts, allowing users to navigate with precision and ease. It combines topographical mapping, sophisticated navigation features, and rugged durability, making it a favorite among hikers, campers, and adventurers.

One of the standout features of the Garmin 210 GEO T DL is its high-sensitivity GPS receiver. This technology ensures accurate tracking even in challenging environments, such as dense forests or mountainous terrains, where signal loss can often be an issue. The device quickly locks onto satellites, providing real-time location data and ensuring that users can follow their routes confidently.

The screen of the 210 GEO T DL is notably user-friendly, featuring a high-resolution display that is easy to read even in bright sunlight. This is particularly beneficial for outdoor use, where visibility can be a challenge. Users can view detailed maps, waypoints, and track information, making the navigation process intuitive and straightforward.

Another important aspect of the Garmin 210 GEO T DL is its extensive mapping capabilities. The device comes preloaded with topographic maps, enabling users to explore diverse terrains without the fear of getting lost. The mapping system also supports the addition of custom maps, allowing users to personalize their navigation experience based on their specific needs and interests.

Battery life is crucial for outdoor equipment, and the Garmin 210 GEO T DL excels in this area. It boasts a robust battery performance, allowing for hours of continuous use. This is essential for long hikes or camping trips, where access to power sources may be limited.

Additionally, this GPS device includes features such as waypoint marking and route planning. Users can easily save locations of interest, such as campsites or scenic overlooks, and navigate back to them later. The built-in compass and barometric altimeter further enhance the outdoor experience, providing users with real-time information on their elevation and direction.

Overall, the Garmin 210 GEO T DL is a reliable and feature-rich GPS device tailored for those who appreciate the great outdoors. Its combination of advanced navigation tools, robust mapping capabilities, and durable design makes it an essential companion for any adventure, ensuring that users can explore with confidence and safety.
Top Page Image Contents