Instructions Safety, Lift-Off Oven Door

Instructions

Care and cleaning of the cooking center.

Instructions Safety

Lift the door straight up and off the hinges.

Lift-Off Oven Door

The oven door is removable for easier access to the light bulb.

Do not lift the door by the handle.

To remove the door, open it to the broil stop position. Grasp firmly on each side and lift the door straight up and off the hinges.

Do not place hands between the hinge and the oven door frame.

To replace the door, make sure the hinges are in the broil stop position. Position the slots in the bottom of the door squarely over the hinges and slowly lower it over both hinges.

Care and Cleaning Operating

The gasket is designed with a gap at the bottom to allow for proper air circulation.

Do not rub or clean the door gasket— it has an extremely low resistance to abrasion.

If you notice the gasket becoming worn, frayed or damaged in any way or if it has become displaced on the door, you should have it replaced.

To clean the inside of the door:

■Because the area inside the gasket is cleaned during the self-clean cycle, you do not need to clean this by hand.

■The area outside the gasket and the door liner can be cleaned with a soap-filled steel wool or plastic pad, hot water and detergent. Rinse well with a vinegar and water solution.

To clean the outside of the door:

■Use soap and water to thoroughly clean the top, sides and front of the oven door. Rinse well. You may also use a glass cleaner to clean the glass on

the outside of the door. Do not let water drip into the vent openings.

■If any stain on the door vent trim is persistent, use a soft abrasive cleaner and a sponge-scrubber for best results.

■Spillage of marinades, fruit juices, tomato sauces and basting materials containing acids may cause discoloration and should be wiped up immediately. When surface is cool, clean and rinse.

■Do not use oven cleaners, cleaning powders or harsh abrasives on the outside of the door.

Consumer Support Troubleshooting Tips

Roasting rack	Oven Shelves and Convection Roasting Rack (lower oven)
	Clean the oven shelves and the	their luster and become hard to slide if cleaned
Oven shelf	convection roasting rack with an abrasive	during the self-cleaning cycle.
	cleanser or steel wool. After cleaning,	To make the shelves slide more easily
	rinse the shelves and rack with clean	To make the shelves slide more easily
	rinse the shelves and rack with clean	apply a small amount of vegetable oil
	water and dry with a clean cloth.	apply a small amount of vegetable oil
	water and dry with a clean cloth.	or cooking oil to a paper towel and wipe
	NOTE: The oven shelves and convection roasting	or cooking oil to a paper towel and wipe
	NOTE: The oven shelves and convection roasting	the edges of the oven shelves with the
	rack may be cleaned in the self-cleaning oven.	paper towel.
	However, the shelves will darken in color, lose

JTP95 specifications

The GE JTP95 is a notable entry in General Electric's line of high-performance jet engines, designed primarily for commercial aviation applications. Known for its advanced technological features, the JTP95 integrates innovative design elements that enhance efficiency, performance, and reliability while minimizing environmental impact.

At the heart of the JTP95 engine is its turbofan configuration, which combines superior thrust capabilities with reduced noise levels. This design not only provides the necessary power for larger aircraft but also adheres to increasingly stringent noise regulations, making it a favorite among carriers operating in noise-sensitive areas.

One of the standout features of the GE JTP95 is its advanced materials technology. The engine incorporates lightweight composite materials and high-strength alloys, which contribute to fuel efficiency while ensuring durability under stress. These materials allow for higher operating temperatures, leading to improved thermal efficiency and overall performance.

The engine utilizes an innovative full authority digital engine control (FADEC) system, which optimizes fuel consumption and engine performance in real-time. This system ensures that the engine operates at peak efficiency throughout various flight conditions, providing pilots with valuable performance data and enhancing safety measures.

Moreover, the JTP95 is designed with a bypass ratio that significantly reduces emissions when compared to older engine models. The high bypass ratio means that a larger proportion of air is directed around the engine core, which not only improves fuel efficiency but also results in lower carbon emissions, aligning with the industry's shift towards more sustainable aviation solutions.

Maintenance is another area where the GE JTP95 excels. The engine features modular design components, allowing for easier access to critical parts during servicing. This reduces downtime and associated costs for airlines, while also enhancing the overall reliability of the engine over its lifespan.

In summary, the GE JTP95 stands out in the aviation sector for its combination of innovative technologies, advanced materials, and efficient design. It exemplifies GE's commitment to developing engines that meet modern demands for performance, reliability, and environmental stewardship, making it a key player in the future of commercial aviation. Organizations looking for a high-performance and environmentally friendly solution for their fleet will find the JTP95 to be an ideal choice.