GE JRP15, JKP15 Using the clock and timer, To Set the Clock, To Set the Timer, To Reset the Timer

Page 14

Instructions

Using the clock and timer.

Safety

Make sure the clock is set to the correct time of day.

To Set the Clock

The clock must be set to the correct time of day for the automatic oven timing functions to work properly. The time of day cannot be changed during a timed baking or self-cleaning cycle.

Press the CLOCK pad.

Press the HOUR and MIN + or pads to set the time of day.

Press the START pad.

Care and Cleaning Operating Instructions

The timer is a minute timer only.

The timer does not control oven operations. The maximum setting on the timer is 9 hours and 59 minutes.

To Set the Timer

Press the KITCHEN TIMER

ON/OFF pad.

Press the HOUR and MIN + or pads until the amount of time you want shows in the display.

If you make a mistake, press KITCHEN TIMER ON/OFF and begin again.

Press the START pad.

After pressing the START pad, SET disappears; this tells you the time is counting down, although the display does not change until one minute has passed.

When the timer reaches :00, the control will beep 3 times followed by one beep every 6 seconds until the KITCHEN TIMER ON/OFF pad is pressed.

The 6 second tone can be canceled by following the steps in the Special features of your oven control section under Tones at the End of a Timed Cycle.

Customer Service Troubleshooting Tips

To Reset the Timer

If the display is still showing the time

If the remaining time is not in the display

remaining, you may change it by pressing

(clock, delay start or cooking time are in

the KITCHEN TIMER ON/OFF pad, then

the display), recall the remaining time by

press the HOUR and MIN + or pads until

pressing the KITCHEN TIMER ON/OFF pad

the time you want appears in the display.

and then pressing the HOUR and MIN +

 

or pads to enter the new time you want.

To Cancel the Timer

Press the KITCHEN TIMER ON/OFF pad twice.

14

Image 14
Contents Wall OvenBuilt-In Electric Write the model and serial numbers here GE & You, a Service PartnershipStaple sales slip or cancelled check here Two easy ways to register your applianceImportant Safety Notice Instructions Customer Service Care and CleaningUsing the oven controls Oven Control, Clock and Timer Features and SettingsFahrenheit or Celsius Temperature Selection Special features of your oven controlCare and Cleaning Hour Shut-OffHour, 24 Hour or Clock Black-Out InstructionsTones at the End of a Timed Cycle Your control is set to use a 12 hour clockChanging the Speed of the + or Pads Safety Instructions OperatingCook and Hold How to Set for Regular Baking/Roasting Safety InstructionsCustomer Service Troubleshooting Tips How to Exit the Sabbath Feature Tips Using the ovenSafety HI Broil How to Set the Oven for BroilingBroiling Guide To Reset the Timer Using the clock and timerTo Set the Timer To Cancel the TimerHow to Set a Delayed Start and Automatic Stop Using the timed baking and roasting featuresHow to Set an Immediate Start and Automatic Stop Safety InstructionsType of margarine will affect baking performance Adjust the oven thermostat-Do it yourselfTo Adjust the Thermostat How to Set the Oven for Cleaning Using the self-cleaning ovenBefore a Clean Cycle Oven must be cool in order to set the self- clean cycleHow to Delay the Start of Cleaning Customer Service Troubleshooting Tips CareAfter a Clean Cycle Lift-Off Oven Door Care and cleaning of the ovenHow to Remove Packaging Tape Oven Heating ElementsInstructions Safety Stainless Steel Surfaces on some models Oven Light Bulb on some modelsBefore You Call For Service… Problem Possible Causes What To DoIs on when you want During clean cycleOpen after a Clean cycle Hot or too coldOr letter flash Power outageA number Display goes blankWe’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration What GE Will Not Cover GE Built-In Electric Oven WarrantyGE Will Replace Warrantor General Electric Company. Louisville, KYService Telephone Numbers GE Answer Center

JRP15, JTP17, JKP15 specifications

GE's JKP15, JTP17, and JRP15 models stand out as exceptional units in the landscape of commercial and industrial gas turbines, each designed to cater to various operational needs. These turbines incorporate advanced technologies and innovations, making them suitable for a wide range of applications from power generation to mechanical drive.

The GE JKP15 turbine is renowned for its efficient energy conversion, showcasing a robust design that ensures high reliability and longevity. It typically features a modular layout, which allows for easy maintenance and reduced downtime, leading to enhanced operational efficiency. The JKP15 utilizes state-of-the-art materials and cooling technologies to maintain performance under high thermal conditions, ensuring optimal efficiency rates and lower emissions.

In contrast, the JTP17 model is designed for larger-scale applications. This turbine integrates advanced aerodynamic designs that increase its efficiency and performance under various load conditions. The JTP17 is equipped with a digital control system, which enhances operational flexibility and process optimization. Its combustion system is engineered to minimize NOx emissions, making it compliant with stringent environmental regulations, thus enhancing its appeal to environmentally conscious operators.

The JRP15, on the other hand, is a versatile model that serves both the power generation sector and industrial applications. It features high operational versatility, allowing for swift changes between different fuel types. The JRP15 is made with advanced engineering techniques, which contribute to its high reliability and low maintenance needs. Its ability to handle fluctuating load demands makes it a prime choice for operators seeking both capacity and efficiency.

All three models share a commitment to advanced monitoring technologies that use real-time data analytics to predict maintenance needs, enhancing their reliability and lifespan. GE's focus on integrating IoT capabilities allows for comprehensive system integration and energy management, paving the way for smarter energy solutions.

In summary, GE's JKP15, JTP17, and JRP15 turbines collectively represent the pinnacle of engineering excellence in gas turbine technology. Their distinct features, from modular designs and digital control systems to low-emission combustion technologies, underscore GE's commitment to innovation, efficiency, and sustainability in energy production. Whether for power generation or industrial uses, these turbines offer reliable solutions that meet the diverse needs of today’s energy landscape.