Safety Instructions Operating Instructions Care

ge.com

Slot

Hinge lock

Pull hinge locks down to unlock

Removal position

Lift-Off Oven Door

The door is very heavy. Be careful when removing and lifting the door.

Do not lift the door by the handle.

To remove the door:

Fully open the door.

Pull the hinge locks down toward the door frame, to the unlocked position. A tool, such as a small flat- blade screwdriver, may be required.

Firmly grasp both sides of the door at the top.

Close door to the door removal position, which is halfway between the broil stop position and fully closed.

Lift door up and out until the hinge arm is clear of the slot.

To replace the door:

Firmly grasp both sides of the door at the top.

With the	Bottom	Hinge arm
door at the	Bottom	Hinge arm
door at the	edge
same angle as	of slot
the removal
position, seat the
indentation of
the hinge arm		Indentation
into the bottom		Indentation
into the bottom
edge of the hinge slot. The notch in
the hinge arm must be fully seated
into the bottom of the slot.

Fully open the door. If the door will not fully open, the indentation is not seated correctly in the bottom edge of the slot.

Push the hinge locks up against the front frame of the oven cavity, to the locked position.

Hinge arm

Hinge lock

Push hinge locks up to lock

Safety Instructions Operating Instructions Care and

Close the oven door.

Cleaning

Do not rub or clean the door gasket— it has an extremely low resistance to abrasion.

If you notice the gasket becoming worn, frayed or damaged in any way or if it has become displaced on the door, you should have it replaced.

To clean the inside of the door:

■Because the area inside the gasket is cleaned during the self-clean cycle, you do not need to clean this by hand.

■The area outside the gasket and the door liner can be cleaned with a soap-filled or plastic scouring pad, hot water and detergent. Rinse well with a vinegar and water solution.

To clean the outside of the door:

■Use soap and water to thoroughly clean the top, sides and front of the oven door. Rinse well. You may also use a glass cleaner to clean the glass on the outside of the door. Do not let water drip into the vent openings.

■If any stain on the door vent trim is persistent, use a soft abrasive cleaner and a sponge-scrubber for best results.

■Spillage of marinades, fruit juices, tomato sauces and basting materials containing acids may cause discoloration and should be wiped up immediately. When surface is cool, clean and rinse.

■Do not use oven cleaners, cleaning powders or harsh abrasives on the outside of the door.

Troubleshooting Tips Consumer Support

JT96530 specifications

The GE JT96530 is a cutting-edge jet engine that represents a significant advancement in aviation technology, specifically designed for use in regional and narrow-body aircraft. As the industry continues to evolve towards increased fuel efficiency and reduced emissions, the JT96530 stands out for its performance, state-of-the-art engineering, and innovative features.

One of the main highlights of the GE JT96530 is its high bypass ratio, which contributes to improved fuel efficiency. The engine's design allows for a larger volume of air to bypass the core engine compared to the amount that goes through the combustion chamber. This not only enhances fuel burn efficiency but also reduces noise, making it an environmentally friendly option for airlines and airports. The incorporation of advanced materials, including lightweight titanium and composite components, further optimizes performance and durability while keeping the engine lightweight.

Technologically, the JT96530 is equipped with advanced digital engine controls that enable precise management of engine performance throughout various phases of flight. This system enhances operational efficiency by allowing for real-time monitoring and adjustments, optimizing fuel consumption, and improving overall engine reliability. The engine's design incorporates a staggered fan blade layout, which enhances airflow and further increases efficiency and thrust.

Additionally, the JT96530 features a robust cooling system that ensures parts are maintained at optimal temperatures, enhancing overall engine longevity. The advanced thermal management techniques not only improve performance but also extend maintenance intervals, reducing operational costs for airlines.

The engine’s maintenance is simplified by the modular design, allowing for quick and efficient servicing. Operators benefit from reduced downtime, increasing aircraft availability and overall operational efficiency. The JT96530 is also designed with a focus on sustainability, aligning with global initiatives to decrease carbon emissions in aviation, making it a preferred choice for environmentally conscious operators.

In summary, the GE JT96530 engine combines advanced aerodynamics, innovative materials, and state-of-the-art technology, setting a new standard in the aviation industry. Its remarkable efficiency, reduced environmental impact, and ease of maintenance make it an ideal choice for airlines looking to modernize their fleet while meeting the demands of a rapidly changing world. This engine not only delivers exceptional performance but also reflects a commitment to sustainable aviation for the future.