GE PDE9900 manual Keypad Assembly PDW9700 Series and PDW9900 Series

Page 13

Keypad Assembly

PDW9700 Series and PDW9900 Series

Top control models have a membrane keypad that is accessed by removing the door panel. (see Door Panel.)

•When removing the membrane keypad, peel the keypad from right to left.

•When installing, make sure the membrane button areas and lights align with the keypad.

•On models with an LED display, the display is held in place by 2 Phillips head screws.

Note: When replacing the keypad membrane, always run the Factory Test Mode to calibrate the keypad membrane to the control board.

PADS CONNECTOR PINS

11 & 17

11 & 16

11 & 15

12 & 15

12 & 16

12 & 17

13 & 15

1

Note: When troubleshooting, always check resistance between pins 18 and 19. The membrane should read approximately 22K Ω.

When a control pad is pressed, continuity is present on the corresponding pins. (See chart.) Example: If the HEATED DRY pad is pressed, you should have continuity between pins 12 and 17. To locate pin numbers, note location of pin 1 for reference point. (See illustration.)

PDW8900 Series

The keypad and ribbon cable are a permanent part of the escutcheon and are replaced as a unit. To remove the escutcheon keypad assembly, remove

the outer door panel and the 4 screws securingActive Vent Worm Gear the escutcheon keypad assembly. (See Door Panel,

PDW8900 Series.)

IMPORTANT: When assembling, the active vent flapper must be closed before the escutcheon keypad assembly is installed. Close the active vent flapper by turning the worm gear clockwise by hand. Failure to do so will cause a misalignment and an increase in noise level.

– 13 –

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Technical Service Guide Important Safety Notice Table of Contents W 9 9 8 0 L 0 0 S S NomenclatureModel Number Serial NumberIntroduction PDW8900 Series Control FeaturesSelections Enhancements Start PDW8900 Series Shown Inside Cabinet View Component Locator Views Left Side View PDW8900 Series Shown Door ViewPDW8900 Series Shown Bottom View PDW9000 Series ShownFront of Dishwasher Rear of DishwasherDoor Panel PDW9700 Series and PDW9900 Series Dishwasher ComponentsPDW8900 Series Keypad Assembly PDW9700 Series and PDW9900 Series SmartDispenseTM Calibration Water Hardness Test and Calibration Test Water HardnessWater Hardness Test Strip Indication Front Mount Control PDW8900Detergent Reservoir SmartDispenseTMTo remove the reservoir Detergent Level Sensor Approximate Detergent Use Positive Displacement PumpTo remove the pump Customer Purge of the Bulk Dispenser Tank When to Purge the Bulk Dispenser TankConsumer Purge Cycle Detergent/Rinse Module Door Interlock Switchfirst time the module is activated Removal and Replacement Using the Dishwasher with the Upper Rack RemovedMiddle Spray Arm Main Conduit Upper Spray ArmFill Funnel Lower Spray Arm, Fine Filter, and Inlet CoverHeating Element Test Turbidity SensorCalibrating the Turbidity Sensor Drain System Smart Fill System Water Valve Test Water Valve and Flood SwitchWash Cycles Demo ModeControl Module Board Control ModuleActive Vent Normal Wash Cycle Single Rack WashTMWax Motor and Magnet Circulation Pump and MotorDoor Spring Installation Description Time Service ModeEntering Factory Test Mode Factory Test ModeVerify operation after Schematics and Strip CircuitsPDW9900 Series PDW9700 SeriesFor The Period GE Will Replace Warranty for 2005 ProductFor The Period GE Will Replace Warranty for 2006 and Later Product
Top Page Image Contents