GE PDE9900 manual Start

Page 9

5Start

PDW8900 Series

Close the dishwasher door and select the cycle and desired enhancements. Touch the START/RESET pad to begin the cycle. Water fill begins immediately, and approximately 60 seconds later the wash action begins.

When the dishwasher door is fully closed, the control panel lights will display the last settings you selected. If you don’t want to change any of the settings, simply touch the START/RESET pad to begin the cycle.

If the door is closed, the indicator lights will turn off if the START/RESET pad is not selected within 5 minutes. To activate the display, open and close the door or press any pad.

PDW9700 and PDW9900 Series

After selecting the cycle and desired enhancements, touch the START/RESET pad to ready the dishwasher to begin the cycle. Close the door to start the cycle or begin the DELAY START countdown. When the cycle starts, the water fill begins and approximately 60 seconds later the wash action begins.

The dishwasher will always display your last selection and enhancements. If you don’t want to change the settings, simply touch the START/RESET pad to ready the dishwasher and close the door to begin the cycle.

Also, if a power failure occurs NORMAL and HEATED DRY will automatically be programmed. Make any new selections and touch the START/RESET pad to begin the new cycle.

If the door is opened, the indicator lights will turn off if the START/RESET pad is not selected within 5 minutes. To activate the display, open and close the door or touch any pad.

6Clean

PDW8900 Series

The CLEAN light is illuminated when the selected cycle and enhancements are complete. The light will stay ON until a pad is pressed or the door is opened and then closed.

PDW9700 and PDW9900 Series

The CLEAN light is illuminated and a double beep will sound when the selected cycle and enhancements are complete. You may remove the dishes at any time. Note the high-efficiency fan will run quietly for 30 minutes to 4 hours (depending on selected cycle) after the CLEAN light is illuminated to continue drying the dishes. The fan can be turned off by opening the door and pressing any keypad.

NOTE: To turn off the audible end-of-cycle signal (or re-activate it if it was previously disengaged), press the HEATED DRY pad 5 times within 3 seconds. A triple beep will sound to indicate the end-of-cycle beep option has been toggled.

NOTE: If you are not using the SmartDispense and you want to turn the LOW DETERGENT LED light off, press the ADDED HEAT pad 5 times within 3 seconds. You will hear three beeps, then the light will go off. You can turn the light back on by pressing the ADDED HEAT pad 5 times within 3 seconds.

– 9 –

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Technical Service Guide Important Safety Notice Table of Contents W 9 9 8 0 L 0 0 S S NomenclatureModel Number Serial NumberIntroduction PDW8900 Series Control FeaturesSelections Enhancements Start PDW8900 Series Shown Inside Cabinet View Component Locator ViewsLeft Side View PDW8900 Series Shown Door ViewPDW8900 Series Shown Bottom View PDW9000 Series ShownFront of Dishwasher Rear of DishwasherDishwasher Components Door Panel PDW9700 Series and PDW9900 SeriesPDW8900 Series Keypad Assembly PDW9700 Series and PDW9900 Series SmartDispenseTM Calibration Water Hardness Test and Calibration Test Water HardnessWater Hardness Test Strip Indication Front Mount Control PDW8900SmartDispenseTM Detergent ReservoirTo remove the reservoir Detergent Level Sensor Positive Displacement Pump Approximate Detergent UseTo remove the pump When to Purge the Bulk Dispenser Tank Customer Purge of the Bulk Dispenser TankConsumer Purge Cycle Door Interlock Switch Detergent/Rinse Modulefirst time the module is activated Using the Dishwasher with the Upper Rack Removed Removal and ReplacementMiddle Spray Arm Main Conduit Upper Spray ArmFill Funnel Lower Spray Arm, Fine Filter, and Inlet CoverHeating Element Turbidity Sensor TestCalibrating the Turbidity Sensor Drain System Smart Fill System Water Valve Test Water Valve and Flood SwitchWash Cycles Demo ModeControl Module Board Control ModuleActive Vent Normal Wash Cycle Single Rack WashTMWax Motor and Magnet Circulation Pump and MotorDoor Spring Installation Description Time Service ModeEntering Factory Test Mode Factory Test ModeVerify operation after Schematics and Strip CircuitsPDW9900 Series PDW9700 SeriesFor The Period GE Will Replace Warranty for 2005 ProductFor The Period GE Will Replace Warranty for 2006 and Later Product
Top Page Image Contents