GE Guide to Using the Unicouple and Unicouple Faucet Adapter for Portable Washers
Page 4

HOW TO USE THE UNICOUPLE

(Portable Models Only)

Before operating your dishwasher the first time...

Attach the Faucet Adapter. The special faucet adapter supplied with your dishwasher must be assembled to the sink faucet before you can use your dishwasher.

The faucet adapter is designed to fit standard spouts having internal or external threads. You will find the adapter and two washers in the ÒFaucet AdapterÕÕ packet in your dishwasher.

To install faucet adapter, first remove the old aerator or trim ring on your faucet spout.

If faucet has external threads:

Insert the thinner of the two washers into the faucet adapter and attach it to the faucet spout.

Tighten with pliers.

If faucet has internal threads:

Insert both washers into the faucet adapter and attach it to the faucet spout.

Tighten with pliers.

If the faucet adapter threads do not match your faucet spout, your local hardware or

plumbing supply store normally has additional fittings to adapt your faucet spout to the special faucet adapter.

NOTE: A sink spray attachment hose can burst if it is installed on the same sink with your dishwasher. We suggest that you disconnect the sink spray attachment if your sink has one and plug the hole.

How to connect the Unicouple

1.Pull Unicouple and its hoses completely out from storage compartment located at rear of dishwasher and attach it to the faucet adapter.

2.Attach the Unicouple connector to the faucet adapter by depressing collar at the top of the connector. When Unicoupler is all the way up onto the adapter, release the collar. It will then snap into position to

lock the Unicouple in

PULL RING DOWN

place.

 

The Unicouple's small hose carries water from the faucet to the dishwasher. Its large hose carries drain water to the sink. Be sure Unicouple is pointing toward the sink bowl drain opening and the sink drain is open for water that will drain from your dishwasher. If your dishwasher drains into a dis- poser, operate the disposer until it is completely empty before starting the dishwasher.

3.Turn hot water fully on before starting the dish- washer.

How to disconnect the Unicouple from faucet adapter

1.Turn off the hot water.

2.Release the water pressure by depressing the pressure release button. This relieves water pressure and protects you, and the room, from severe splashing.

3.Release Unicouple from faucet by depressing the collar at the top of the Unicouple connector.

How to disconnect your dishwasher

1.Remove the power cord plug from the wall receptacle.

2.Disconnect Unicouple from faucet adapter.

NOTE: When motor stops at the end of the final rinse, the Unicouple can be disconnected and returned to storage.

How to drain excess water from Unicouple hoses

If the sink is 34" or higher from the floor, the excess water in Unicouple hoses cannot be drained directly into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable container that is held outside and lower than the sink.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Use and Care Guide If you received a damaged dishwasher… Important Safety Instructions Read all instructions before using this applianceImportant Safety Instructions To minimize the possibility of injuryHOW to USE the Unicouple HOW to Connect Electricity Electrical requirements How to Connect UnicoupleHow to Connect ElectricityModels With Delay HOW to Operate Your DishwasherModels Without Delay HOW to GET Started 3 Easy Steps InstructionsHow to Test Water Temperature How to Use a Rinse AgentTo get dishes clean and dry you need hot water How to fill the rinse agent dispenserHow to Choose and Use the Right Detergent Hot Water Loading DetergentRinse Agents DetergentsHOW to Load Your Dishwasher Place settingsUpper Rack Lower RackWash Tower Silverware BasketsKeep the center area clear in the lower rack DonÕt let any item extend through bottomAbout Optional Accessories Descriptions of Optional AccessoriesConversion Kit ¥ GPF325A Almond ¥ GPF325B Black ¥ GPF325W WhiteCare and Cleaning Care & Cleaning of the DishwasherBefore using, wipe well with a dry cloth to Care of the Dishwasher TopYES What YOU can Usually Wash Safely Your DishwasherGlass YES BUILT-IN Dishwasher Installation Instructions Materials YOU will NeedPrepare Drain Plumbing Follow local codes and ordinancesPrepare Electrical Wiring InstallationDishwasher Sold With Power Cord Do not install receptacle in cabinet opening for dishwasherRemove leveling legs and wood base Install Leveling legs Figure H Remove access panel and toekickPosition water line and power supply Align water and electrical linesLevel dishwasher Position dishwasher and fasten to cabinetInstaller Oxidant compound and aluminum-to-copper connectorsConnect drain line Follow all local codes and ordinancesPre-test check list „ Check to be sure power is off Replace access panel and toekick„ Turn on water supply Dishwasher wet test check listQUESTIONS? USE this Problem Solver Problem Solver To remove stubborn spots and film from glasswareProblem Possible Cause Small Amount of Water Standing in the BottomTUB Water Wonõt Pump OUT TUBCamco Service Problem Solver Camco ServiceTo continue installation go to Prepare Enclosure for AN Undersink Dishwasher

500A200P047 specifications

The GE 500A200P047 is a notable component within General Electric's extensive portfolio of innovative technologies. Widely recognized for its robust design and high performance, this device plays a pivotal role in various applications, particularly in industrial automation and power systems.

One of the standout features of the GE 500A200P047 is its exceptional reliability. Engineered for demanding environments, it is built to withstand extreme temperatures, vibrations, and other challenging conditions that are common in industrial settings. This reliability ensures that the component maintains optimal performance over time, reducing downtime and maintenance costs for operators.

The GE 500A200P047 also incorporates state-of-the-art technology aimed at enhancing efficiency and functionality. It features advanced digital controls, which allow for precise monitoring and management of electrical systems. This technological integration not only optimizes power distribution but also contributes to energy savings, making it an eco-friendly choice for enterprises looking to reduce their carbon footprint.

Furthermore, this component is designed with versatility in mind. It supports a range of applications, from low-voltage distributions to high-power industrial machinery. This adaptability makes the GE 500A200P047 a preferred choice among engineers and designers who require flexibility in their designs while ensuring top-tier performance.

Another notable characteristic of the GE 500A200P047 is its user-friendly interface. The design includes intuitive controls and diagnostic tools, facilitating easier operation and troubleshooting. This user-centric approach simplifies the complexity often associated with industrial systems, enabling quicker resolution of issues and enhancing overall productivity.

In terms of safety, the GE 500A200P047 is equipped with multiple safety features designed to protect both the system and its operators. These safety technologies prevent overload, short circuits, and other hazardous conditions, ensuring that operations run smoothly and securely.

In conclusion, the GE 500A200P047 stands out as a powerhouse in the industrial technology sector. With its impressive reliability, advanced digital controls, versatility, user-friendly interface, and robust safety features, it serves as a crucial component in modern industrial networks. Organizations looking to enhance efficiency and reliability in their operations will find the GE 500A200P047 to be an invaluable addition to their technological arsenal.
Top Page Image Contents