GE 500A200P047 How to Choose and Use the Right Detergent, Hot Water Loading Detergent, Detergents

Page 9
GRASP HANDLE, ROTATE AND CLOSE TIGHTLY

How to Choose and Use the Right Detergent

First, use only powder or liquid detergent specifically made for use in dishwashers. Other types will cause over sudsing..

Second, check phosphate content. Phosphate helps prevent hard-water materials from forming spots or film on dishes. If your water is hard (7 grains or more), your detergent has to work harder. Detergents with a higher phosphate level will probably work better. If phosphate content is low (8.7% or less), you'll have to use extra detergent with hard water.

Your water department can tell you how hard your water is. So can your county extension agent or your area's water softener company. Just call and ask them how many ÒgrainsÓ of hardness there are in your water.

How much detergent should you use? That depends. Is your water ÒhardÓ or ÒsoftÓ? With

hard water, you need extra detergent to get dishes clean. With soft water, you need less detergent.

Too much detergent with soft water not only wastes money, it can be harmful. It can cause a permanent cloudiness of glassware, called ÒetchingÓ. An outside layer of glass is etched away! Of course, this takes some time. But why take a chance when it's easy to find out the hardness of your water.

Keep detergent fresh and dry. Under the sink isn't a good place to store detergent because there is too much moisture. Don't put powder detergent into dispenser until you're ready to wash dishes, either. (It won't be fresh OR dry.)

Some detergents contain colorant (pigment or dyes) that will discolor the tub interior with extended use. Check the detergent cup for signs of any discoloration. If cup is discolored, change to detergent without any colorant.

Hot Water

Loading Detergent

You'll find two detergent dispensers on the inside door of your dishwasher. Two, because some cycles use two washes.

(Be sure the CYCLE

OPEN

INDICATOR DIAL is

at OFF position before

CUP

adding detergent.

 

 

Otherwise, the

 

 

detergent cup will not

 

 

close and latch

 

 

MAIN

 

properly).

 

CUP

 

 

 

 

 

 

Close the main cup.

NOTE: To open the detergent cup after it has been closed, unlatch the

door and rotate the Cycle Indicator Dial a full turn to

the OFF position. When the closed cup contains soap it is best that the door be in a partially open position

before rotating the Cycle Indicator Dial. This will help reduce the amount of detergent and rinse aid agent spillage into the tub.

Rinse Agents

Try the Cascade that best meets your own needs!

For Virtually

No need to pre-wash

Spotless results!

your dishes

9

Detergents

Image 9
Contents Use and Care Guide If you received a damaged dishwasher… Read all instructions before using this appliance Important Safety InstructionsImportant Safety Instructions To minimize the possibility of injuryHOW to USE the Unicouple Electrical requirements How to Connect Unicouple HOW to Connect ElectricityHow to Connect ElectricityHOW to Operate Your Dishwasher Models With DelayModels Without Delay Instructions HOW to GET Started 3 Easy StepsHow to Use a Rinse Agent How to Test Water TemperatureTo get dishes clean and dry you need hot water How to fill the rinse agent dispenserHot Water Loading Detergent How to Choose and Use the Right DetergentRinse Agents DetergentsPlace settings HOW to Load Your DishwasherUpper Rack Lower RackSilverware Baskets Wash TowerKeep the center area clear in the lower rack DonÕt let any item extend through bottomDescriptions of Optional Accessories About Optional AccessoriesConversion Kit ¥ GPF325A Almond ¥ GPF325B Black ¥ GPF325W WhiteCare & Cleaning of the Dishwasher Care and CleaningBefore using, wipe well with a dry cloth to Care of the Dishwasher TopWhat YOU can Usually Wash Safely Your Dishwasher YESGlass YES Materials YOU will Need BUILT-IN Dishwasher Installation InstructionsFollow local codes and ordinances Prepare Drain PlumbingInstallation Prepare Electrical WiringDishwasher Sold With Power Cord Do not install receptacle in cabinet opening for dishwasherFigure H Remove access panel and toekick Remove leveling legs and wood base Install Leveling legsAlign water and electrical lines Position water line and power supplyLevel dishwasher Position dishwasher and fasten to cabinetOxidant compound and aluminum-to-copper connectors InstallerConnect drain line Follow all local codes and ordinancesReplace access panel and toekick Pre-test check list „ Check to be sure power is off„ Turn on water supply Dishwasher wet test check listQUESTIONS? USE this Problem Solver To remove stubborn spots and film from glassware Problem SolverStanding in the Bottom Problem Possible Cause Small Amount of WaterTUB Water Wonõt Pump OUT TUBProblem Solver Camco Service Camco ServicePrepare Enclosure for AN Undersink Dishwasher To continue installation go to

500A200P047 specifications

The GE 500A200P047 is a notable component within General Electric's extensive portfolio of innovative technologies. Widely recognized for its robust design and high performance, this device plays a pivotal role in various applications, particularly in industrial automation and power systems.

One of the standout features of the GE 500A200P047 is its exceptional reliability. Engineered for demanding environments, it is built to withstand extreme temperatures, vibrations, and other challenging conditions that are common in industrial settings. This reliability ensures that the component maintains optimal performance over time, reducing downtime and maintenance costs for operators.

The GE 500A200P047 also incorporates state-of-the-art technology aimed at enhancing efficiency and functionality. It features advanced digital controls, which allow for precise monitoring and management of electrical systems. This technological integration not only optimizes power distribution but also contributes to energy savings, making it an eco-friendly choice for enterprises looking to reduce their carbon footprint.

Furthermore, this component is designed with versatility in mind. It supports a range of applications, from low-voltage distributions to high-power industrial machinery. This adaptability makes the GE 500A200P047 a preferred choice among engineers and designers who require flexibility in their designs while ensuring top-tier performance.

Another notable characteristic of the GE 500A200P047 is its user-friendly interface. The design includes intuitive controls and diagnostic tools, facilitating easier operation and troubleshooting. This user-centric approach simplifies the complexity often associated with industrial systems, enabling quicker resolution of issues and enhancing overall productivity.

In terms of safety, the GE 500A200P047 is equipped with multiple safety features designed to protect both the system and its operators. These safety technologies prevent overload, short circuits, and other hazardous conditions, ensuring that operations run smoothly and securely.

In conclusion, the GE 500A200P047 stands out as a powerhouse in the industrial technology sector. With its impressive reliability, advanced digital controls, versatility, user-friendly interface, and robust safety features, it serves as a crucial component in modern industrial networks. Organizations looking to enhance efficiency and reliability in their operations will find the GE 500A200P047 to be an invaluable addition to their technological arsenal.