GE 500A200P047 Position water line and power supply, Align water and electrical lines

Page 19

INSTALLATION INSTRUCTIONS

Step 5. Position water line and power supply

Position the water supply line and house wiring on the floor of the opening to avoid interference with base of dishwasher and components under dishwasher.

Water Power

Line Supply

Figure K

Step 6. Insert drain hose through cabinet

Upright dishwasher and position in front of the cabinet opening. Insert the drain hose into the hole previously drilled in the cabinet wall. If a power cord is used, guide the end through a separate hole cut for the electrical cord.

Step 8. Align water and electrical lines

Route the water line and electrical supply to their connection locations under the dishwasher. Do not connect water and electrical in this step.

Step 9. Level dishwasher

Level the dishwasher by adjusting the four leveling legs individually for correct alignment. See Figure N. Dishwasher should be level left to right and front to back for proper

dish rack operation and dishwasher performance. Dishwasher door should

be in alignment with adjacent cabinets. Figure N See Figure O.

Step 10. Position dishwasher and fasten to cabinet

Open the door and position the dishwasher tub flange 3/4Ó from the cabinet opening. Fasten the dishwasher to the underside of the countertop, using the 2 Phillips screws provided in Step 1. Be sure screws are driven straight and flush to avoid interference with door operation. See Figure O.

Installation

Figure L

Step 7. Slide dishwasher into cabinet

Slide the dishwasher into the opening a few inches at a time.

Important: Make sure that dishwasher is

centered in the opening and there is no interference with cabinets when opening

or closing the

door. Interference

may cause a

water leak when dishwasher is in operation.

3/4"

Figure O

Instructions

As you proceed, pull the drain hose through the opening and under the sink. Make sure drain hose is not kinked under dishwasher. Check to be sure there is no interference with water line and wiring.

DO NOT PUSH AGAINST FRONT DOOR PANEL WITH YOUR KNEE. Damage to the door panel will occur.

Step 11. Connect water supply

Connect water supply line to 90¡ elbow installed in Step 4.

Figure P

Hot Water

Figure M

90° Elbow

Supply

19

Image 19
Contents Use and Care Guide If you received a damaged dishwasher… To minimize the possibility of injury Important Safety InstructionsRead all instructions before using this appliance Important Safety InstructionsHOW to USE the Unicouple Connect Electricity HOW to Connect ElectricityElectrical requirements How to Connect Unicouple How toModels With Delay HOW to Operate Your DishwasherModels Without Delay Instructions HOW to GET Started 3 Easy StepsHow to fill the rinse agent dispenser How to Test Water TemperatureHow to Use a Rinse Agent To get dishes clean and dry you need hot waterDetergents How to Choose and Use the Right DetergentHot Water Loading Detergent Rinse AgentsLower Rack HOW to Load Your DishwasherPlace settings Upper RackDonÕt let any item extend through bottom Wash TowerSilverware Baskets Keep the center area clear in the lower rack¥ GPF325A Almond ¥ GPF325B Black ¥ GPF325W White About Optional AccessoriesDescriptions of Optional Accessories Conversion KitCare of the Dishwasher Top Care and CleaningCare & Cleaning of the Dishwasher Before using, wipe well with a dry cloth toYES What YOU can Usually Wash Safely Your DishwasherGlass YES Materials YOU will Need BUILT-IN Dishwasher Installation InstructionsFollow local codes and ordinances Prepare Drain PlumbingDo not install receptacle in cabinet opening for dishwasher Prepare Electrical WiringInstallation Dishwasher Sold With Power CordFigure H Remove access panel and toekick Remove leveling legs and wood base Install Leveling legsPosition dishwasher and fasten to cabinet Position water line and power supplyAlign water and electrical lines Level dishwasherFollow all local codes and ordinances InstallerOxidant compound and aluminum-to-copper connectors Connect drain lineDishwasher wet test check list Pre-test check list „ Check to be sure power is offReplace access panel and toekick „ Turn on water supplyQUESTIONS? USE this Problem Solver To remove stubborn spots and film from glassware Problem SolverTUB Problem Possible Cause Small Amount of WaterStanding in the Bottom TUB Water Wonõt Pump OUTProblem Solver Camco Service Camco ServicePrepare Enclosure for AN Undersink Dishwasher To continue installation go to

500A200P047 specifications

The GE 500A200P047 is a notable component within General Electric's extensive portfolio of innovative technologies. Widely recognized for its robust design and high performance, this device plays a pivotal role in various applications, particularly in industrial automation and power systems.

One of the standout features of the GE 500A200P047 is its exceptional reliability. Engineered for demanding environments, it is built to withstand extreme temperatures, vibrations, and other challenging conditions that are common in industrial settings. This reliability ensures that the component maintains optimal performance over time, reducing downtime and maintenance costs for operators.

The GE 500A200P047 also incorporates state-of-the-art technology aimed at enhancing efficiency and functionality. It features advanced digital controls, which allow for precise monitoring and management of electrical systems. This technological integration not only optimizes power distribution but also contributes to energy savings, making it an eco-friendly choice for enterprises looking to reduce their carbon footprint.

Furthermore, this component is designed with versatility in mind. It supports a range of applications, from low-voltage distributions to high-power industrial machinery. This adaptability makes the GE 500A200P047 a preferred choice among engineers and designers who require flexibility in their designs while ensuring top-tier performance.

Another notable characteristic of the GE 500A200P047 is its user-friendly interface. The design includes intuitive controls and diagnostic tools, facilitating easier operation and troubleshooting. This user-centric approach simplifies the complexity often associated with industrial systems, enabling quicker resolution of issues and enhancing overall productivity.

In terms of safety, the GE 500A200P047 is equipped with multiple safety features designed to protect both the system and its operators. These safety technologies prevent overload, short circuits, and other hazardous conditions, ensuring that operations run smoothly and securely.

In conclusion, the GE 500A200P047 stands out as a powerhouse in the industrial technology sector. With its impressive reliability, advanced digital controls, versatility, user-friendly interface, and robust safety features, it serves as a crucial component in modern industrial networks. Organizations looking to enhance efficiency and reliability in their operations will find the GE 500A200P047 to be an invaluable addition to their technological arsenal.