GE 500A200P047 installation instructions Prepare Drain Plumbing, Follow local codes and ordinances

Page 16

PREPARE DRAIN PLUMBING

DRAIN REQUIREMENTS

¥Follow local codes and ordinances.

¥If dishwasher is not adjacent to sink, horizontal drain line should not be longer than 10 feet and should not contain more than three 90¡ long radius turns.

DRAIN PREPARATION

A drain hose already connected to the pump outlet is supplied with the dishwasher. If the drain hose is not long enough and has to be extended, use a 1/2" O.D. copper tubing with clamp.

o countertop

32" 18" Min. Min.

Under the sink connection Hose may be fastened to underside of countertop

IMPORTANT

20"

Min.

 

Installation directly

Fig. C

through the floor

THE RUBBER END OF THE DRAIN HOSE MAY BE CUT OFF TO ACCOMMODATE THE FOLLOWING SIZES OF TAIL PIECE OR WASTE TEE: 5/8", 3/4" OR 1"

1.A suggested method of connecting the drain hose to a WASTE TEE or a Y branch tailpiece on the existing sink trap is shown in Figure C. They are made by several manufacturers purposely for electric dishwashers.

2.When connecting the drain hose to a DISPOSER, remove hopper plug before making connection.

Install waste tee or disposer according to manufacturerÕs instructions.

TO PREVENT POSSIBLE DRAIN FROM SINK INTO DISHWASHER OR SIPHONING OF DISHWASHER WATER, DRAIN LINE MUST BE ROUTED AS FOLLOWS:

MIN. 30" ABOVE THE FLOOR FOR UNDER THE SINK CONNECTION.

MIN. 20" ABOVE THE FLOOR FOR INSTALLATION DIRECTLY THROUGH THE FLOOR.

Note: be sure to remove drain plug from disposer before attaching drain line. dishwasher will not drain if plug is left in place.

CABINET PREPARATION

Drill 1-1/2Ó inch diameter hole in the cabinet wall within the shaded area shown in Figure A for the drain hose. Make sure there are no sharp edges.

Drain hose will be passed through this hole and connected to the drain in a later step.

PREPARE HOT WATER LINE

Follow local codes and ordinances.

1.The hot water line may enter from either side, the rear or from the floor within the shaded area shown in Figure D.

2.Cut a hole approximately 1-1/2Ó dia. within the shaded area to admit the line.

3.Turn off the water supply.

4.Install a hand shut-off valve in the supply line in an accessible location, such as under the sink. (The shut-off valve is optional, but recommended and may be required by local codes.)

5.Water connection is on left side of dishwasher. Install the hot water inlet line, using no less than 3/8Ó O.D. copper tubing or 1/2Ó O.D. plastic tubing. Route line as shown in Figure D. Extend the water line forward at least 19Ó from rear wall.

6.The water valve has a 3/8 N.P.T. internal thread. We recommend use of 90 degrees elbow for connection of copper tubing to water valve. (See Figure E)

Valve

Compression

Nut

 

Ring

 

 

Copper

Tubing

Elbow

 

1-1/2" Dia.

5"

4"

5"

4"

Shut-off

Hole

 

 

 

 

Valve

 

 

 

 

 

Hot

 

 

 

 

 

2"

 

 

 

 

6"

 

 

 

 

 

from

 

19" from Wall

 

 

Cabinet

 

 

 

 

 

 

 

 

Cabinet Face

 

 

2" from Floor

 

Figure D

 

 

 

 

7.Adjust the water heater to deliver water between the temperatures of 120¡F and 150¡F as it comes in the dishwasher.

8.Flush water line to clean out debris.

9.The water pressure of the hot water supply line must be between 20-120 PSI.

16

Image 16
Contents Use and Care Guide If you received a damaged dishwasher… Important Safety Instructions Read all instructions before using this applianceImportant Safety Instructions To minimize the possibility of injuryHOW to USE the Unicouple HOW to Connect Electricity Electrical requirements How to Connect UnicoupleHow to Connect ElectricityModels With Delay HOW to Operate Your DishwasherModels Without Delay HOW to GET Started 3 Easy Steps InstructionsHow to Test Water Temperature How to Use a Rinse AgentTo get dishes clean and dry you need hot water How to fill the rinse agent dispenserHow to Choose and Use the Right Detergent Hot Water Loading DetergentRinse Agents DetergentsHOW to Load Your Dishwasher Place settingsUpper Rack Lower RackWash Tower Silverware BasketsKeep the center area clear in the lower rack DonÕt let any item extend through bottomAbout Optional Accessories Descriptions of Optional AccessoriesConversion Kit ¥ GPF325A Almond ¥ GPF325B Black ¥ GPF325W WhiteCare and Cleaning Care & Cleaning of the DishwasherBefore using, wipe well with a dry cloth to Care of the Dishwasher TopYES What YOU can Usually Wash Safely Your DishwasherGlass YES BUILT-IN Dishwasher Installation Instructions Materials YOU will NeedPrepare Drain Plumbing Follow local codes and ordinancesPrepare Electrical Wiring InstallationDishwasher Sold With Power Cord Do not install receptacle in cabinet opening for dishwasherRemove leveling legs and wood base Install Leveling legs Figure H Remove access panel and toekickPosition water line and power supply Align water and electrical linesLevel dishwasher Position dishwasher and fasten to cabinetInstaller Oxidant compound and aluminum-to-copper connectorsConnect drain line Follow all local codes and ordinancesPre-test check list „ Check to be sure power is off Replace access panel and toekick„ Turn on water supply Dishwasher wet test check listQUESTIONS? USE this Problem Solver Problem Solver To remove stubborn spots and film from glasswareProblem Possible Cause Small Amount of Water Standing in the BottomTUB Water Wonõt Pump OUT TUBCamco Service Problem Solver Camco ServiceTo continue installation go to Prepare Enclosure for AN Undersink Dishwasher

500A200P047 specifications

The GE 500A200P047 is a notable component within General Electric's extensive portfolio of innovative technologies. Widely recognized for its robust design and high performance, this device plays a pivotal role in various applications, particularly in industrial automation and power systems.

One of the standout features of the GE 500A200P047 is its exceptional reliability. Engineered for demanding environments, it is built to withstand extreme temperatures, vibrations, and other challenging conditions that are common in industrial settings. This reliability ensures that the component maintains optimal performance over time, reducing downtime and maintenance costs for operators.

The GE 500A200P047 also incorporates state-of-the-art technology aimed at enhancing efficiency and functionality. It features advanced digital controls, which allow for precise monitoring and management of electrical systems. This technological integration not only optimizes power distribution but also contributes to energy savings, making it an eco-friendly choice for enterprises looking to reduce their carbon footprint.

Furthermore, this component is designed with versatility in mind. It supports a range of applications, from low-voltage distributions to high-power industrial machinery. This adaptability makes the GE 500A200P047 a preferred choice among engineers and designers who require flexibility in their designs while ensuring top-tier performance.

Another notable characteristic of the GE 500A200P047 is its user-friendly interface. The design includes intuitive controls and diagnostic tools, facilitating easier operation and troubleshooting. This user-centric approach simplifies the complexity often associated with industrial systems, enabling quicker resolution of issues and enhancing overall productivity.

In terms of safety, the GE 500A200P047 is equipped with multiple safety features designed to protect both the system and its operators. These safety technologies prevent overload, short circuits, and other hazardous conditions, ensuring that operations run smoothly and securely.

In conclusion, the GE 500A200P047 stands out as a powerhouse in the industrial technology sector. With its impressive reliability, advanced digital controls, versatility, user-friendly interface, and robust safety features, it serves as a crucial component in modern industrial networks. Organizations looking to enhance efficiency and reliability in their operations will find the GE 500A200P047 to be an invaluable addition to their technological arsenal.