GE 500A200P047 Connect drain line, Follow all local codes and ordinances, Installer

Page 20

INSTALLATION INSTRUCTIONS

Step 12. Connect drain line

Follow all local codes and ordinances.

DRAIN LINE PREPARATION

1.All models are supplied with a pre-attached 78Ó long corrugated drain hose. The molded end is designed to fit 5/8Ó, 3/4Ó or 1Ó diameter connections to the waste tee or disposer. Cut on premarked line as required for your installation as illustrated in Figure Q.

Note: DO NOT CUT CORRUGATED PORTION OF HOSE.

 

Cut Lines

Do not cut corrugated

 

 

 

portion of hose

1"

3/4"

5/8"

 

Figure Q

If the location requires a longer drain hose, add up to 42Ó length to the factory installed hose. Use 5/8Ó inside diameter hose and thin wall copper coupler to join the hose ends. Secure connection with appropriate clamps (not supplied).

Note: TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 10 FEET FOR PROPER DRAIN OPERATION.

DRAIN LINE INSTALLATION

Connect drain line to waste tee or disposer as previously outlined in “Prepare Drain Plumbing” section of this manual. Refer to Figure S. Secure connection using appropriate clamps (not supplied).

Make sure drain hose is not kinked.

 

32"

 

 

18"

Min.

Fig. R

20"

 

Min.

 

 

Min.

 

 

 

Under the sink connection

Installation directly

Hose may be fastened to

through the floor

underside of countertop

 

IMPORTANT: TO PREVENT POSSIBLE DRAIN FROM SINK INTO DISHWASHER OR SIPHONING OF DISHWASHER WATER, DRAIN LINE MUST BE ROUTED AS FOLLOWS:

MIN. 30Ó ABOVE THE FLOOR FOR UNDER THE SINK CONNECTION.

MIN. 20Ó ABOVE THE FLOOR FOR INSTAL-LATION DIRECTLY THROUGH THE FLOOR.

20

Step 13. Connect power supply

Verify that power is turned off at source. If power cord is used, plug it into the wall outlet and go to Step 14.

If dishwasher is to be directly wired to house wiring, continue with this step.

Remove junction box cover.

Secure the power supply cable to the back of the junction box with a strain relief (not supplied). Connect incoming wires to dishwasher wires using wire nuts of appropriate size. Connect incoming white to white wire, black to black wire and incoming ground to green wire as shown in Figure S. Replace the junction box cover.

WARNING If house wiring is not 2-wire as shown in Figure S with a ground wire, a ground must be provided by

the installer.

When house wiring is aluminum, be sure to use UL/CSA. recognized anti-

oxidant compound and aluminum-to-copper connectors.

WARNING Check to be sure that wiring is not pinched or in contact with the door springs.

NOTE: Check that harness

 

leads are threaded through

 

small hole in bracket.

Ground

White

 

Neutral

 

Black

Live

Figure S

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Use and Care Guide If you received a damaged dishwasher… Important Safety Instructions Read all instructions before using this applianceImportant Safety Instructions To minimize the possibility of injuryHOW to USE the Unicouple HOW to Connect Electricity Electrical requirements How to Connect UnicoupleHow to Connect ElectricityModels Without Delay HOW to Operate Your DishwasherModels With Delay HOW to GET Started 3 Easy Steps InstructionsHow to Test Water Temperature How to Use a Rinse AgentTo get dishes clean and dry you need hot water How to fill the rinse agent dispenserHow to Choose and Use the Right Detergent Hot Water Loading DetergentRinse Agents DetergentsHOW to Load Your Dishwasher Place settingsUpper Rack Lower RackWash Tower Silverware BasketsKeep the center area clear in the lower rack DonÕt let any item extend through bottomAbout Optional Accessories Descriptions of Optional AccessoriesConversion Kit ¥ GPF325A Almond ¥ GPF325B Black ¥ GPF325W WhiteCare and Cleaning Care & Cleaning of the DishwasherBefore using, wipe well with a dry cloth to Care of the Dishwasher TopGlass YES What YOU can Usually Wash Safely Your DishwasherYES BUILT-IN Dishwasher Installation Instructions Materials YOU will NeedPrepare Drain Plumbing Follow local codes and ordinancesPrepare Electrical Wiring InstallationDishwasher Sold With Power Cord Do not install receptacle in cabinet opening for dishwasherRemove leveling legs and wood base Install Leveling legs Figure H Remove access panel and toekickPosition water line and power supply Align water and electrical linesLevel dishwasher Position dishwasher and fasten to cabinetInstaller Oxidant compound and aluminum-to-copper connectorsConnect drain line Follow all local codes and ordinancesPre-test check list „ Check to be sure power is off Replace access panel and toekick„ Turn on water supply Dishwasher wet test check listQUESTIONS? USE this Problem Solver Problem Solver To remove stubborn spots and film from glasswareProblem Possible Cause Small Amount of Water Standing in the BottomTUB Water Wonõt Pump OUT TUBCamco Service Problem Solver Camco ServiceTo continue installation go to Prepare Enclosure for AN Undersink Dishwasher

500A200P047 specifications

The GE 500A200P047 is a notable component within General Electric's extensive portfolio of innovative technologies. Widely recognized for its robust design and high performance, this device plays a pivotal role in various applications, particularly in industrial automation and power systems.

One of the standout features of the GE 500A200P047 is its exceptional reliability. Engineered for demanding environments, it is built to withstand extreme temperatures, vibrations, and other challenging conditions that are common in industrial settings. This reliability ensures that the component maintains optimal performance over time, reducing downtime and maintenance costs for operators.

The GE 500A200P047 also incorporates state-of-the-art technology aimed at enhancing efficiency and functionality. It features advanced digital controls, which allow for precise monitoring and management of electrical systems. This technological integration not only optimizes power distribution but also contributes to energy savings, making it an eco-friendly choice for enterprises looking to reduce their carbon footprint.

Furthermore, this component is designed with versatility in mind. It supports a range of applications, from low-voltage distributions to high-power industrial machinery. This adaptability makes the GE 500A200P047 a preferred choice among engineers and designers who require flexibility in their designs while ensuring top-tier performance.

Another notable characteristic of the GE 500A200P047 is its user-friendly interface. The design includes intuitive controls and diagnostic tools, facilitating easier operation and troubleshooting. This user-centric approach simplifies the complexity often associated with industrial systems, enabling quicker resolution of issues and enhancing overall productivity.

In terms of safety, the GE 500A200P047 is equipped with multiple safety features designed to protect both the system and its operators. These safety technologies prevent overload, short circuits, and other hazardous conditions, ensuring that operations run smoothly and securely.

In conclusion, the GE 500A200P047 stands out as a powerhouse in the industrial technology sector. With its impressive reliability, advanced digital controls, versatility, user-friendly interface, and robust safety features, it serves as a crucial component in modern industrial networks. Organizations looking to enhance efficiency and reliability in their operations will find the GE 500A200P047 to be an invaluable addition to their technological arsenal.
Top Page Image Contents