Thermador PRG304, PRDS36, PRDS48, PRDS304 installation instructions Final Check List, GAS Supply

Page 25

FINAL CHECK LIST

aPlacement of unit.

Specified clearances maintained to cabinet surfaces.

LJ Unit Level - front to back - side to side.

Burner caps positioned properly on sealed burner bases.

All packaging material removed.

QBackguard attached (if horizon tal clearance to combustible materials behind cooking surface is less than 12").

Zl Ceramic briquettes bag placed in grill unit (if equipped) per instructions enclosed.

_) The stainless steel grill housing (if equipped) is in place. The ceramic briquettes are placed on grill tray per instruction enclosed.

GAS SUPPLY

aConnection: 1/2" N.P.T. with a minimum 5/8" diameter flex line.

rJ The appliance is connected only to the type of gas for which it is certified for use.

Manual gas shut off valve installed in an accessible location (without requiring removal of range).

Unit tested and free of gas leaks.

Gas supply pressure does not exceed 14" (37mb) W.C.

ELECTRICAL

QReceptacle with correct over- current protection is provided for service cord connection.

Proper ground connection.

QProper polarity at receptacle.

Kick panel in place and two (2)

screws secure.

OPERATION

QAll internal packing materials removed. Check below grates and grill pans and within oven(s).

If used on propane gas, verify that the propane gas supply is equipped with its own high pressure regulator in addition to the pressure regulator supplied with the appliance.

INSTALLER CHECKLIST

QBurner caps properly seated into burner bases with align ment pins engaged.

QGrill components properly seated (not all models). Refer to Use & Care Manual for Grill details.

QBezels centered on burner knobs, and knobs turn freely.

QEach burner lights satisfacto rily, both individually and with other burners operating.

QAir Shutter adjustment for proper flame made for Grill. Griddle and Gas Oven. See Step 8 and Fig.23.

Griddle is level or tilted slightly forward and does not rock (not all models).

QOven door hinges seated and hinge locks in proper position. Door opens and closes properly. CTwo doors on Model PRDS48.)

QBurner grates correctly posi tioned, level, and do not rock.

Page 23

Image 25
Contents Gas Supply CorporationDo not try to light any appliance What to do If YOU Smell GASIf you cannot reach your gas supplier, call Fire department Small electric oven with a breadAvertissement Danger DE Renversement Avertissements EN FrancaisCE QUI Faire SI Vous Avertissement LES Degats DE LA ProtrieteTouteslescuisinieres Risques D* ElectrocutionIsland Installation Wall InstallationVentilation Requirements VTrim. See Steps 2Wan Cabinet ClearancesSide View 30, 36 and 48 Ranges Cabinet PreparationGrounding plug. IT Must be Plugged GAS and Electric Supply ZonesModel Electrical SUPPLY, Dual Fuel Ranges Power Cord & Receptacle Junction Box & ConduitAll Ranges Removal UNPACKING, Moving and Placing the RangeUNPACKING, Moving and Placing the Range Range Tipping Hazard Installing ANTI-TIP DeviceALL Ranges can TIP PRG36 All-Gas Ranges Important Installation InformationPrepare holes at fastener locations as identified below Plan View Step B Set the bracket on the floor and turn itSide View PRDS304 and PRDS36 Dual-Fuel Ranges Figures 11, 14 Prds Floor Mount Prds Wall MountHook UP GAS Requirements and HookupManifold Pressure 10 water column 24.9 mb Phase Unit and remove cover. Refer to For P*RDS304 rangeGround Wire Wire Lead ConnectionWire Connection Cupped WasherPRG48 Grounding MethodUnder ANY CIRCUMSTANCES, be CUT or Removed PROS36 and PRDS48 Case 2 Electrical Connections and Grounding Backguard Installation Backguard must be attached PRDS36/PRG36Test and Adjustment Griddle 3/4 4to Grill 1/4 1/2 To Clean and Protect Exterior SurfacesGAS Supply Final Check ListPage Page Corporation Thermador
Related manuals
Manual 28 pages 24.58 Kb