GE TPX24PBDAA, TPX24PBDCC Shut Off the Main Water Supply, Operating, Instructions Installation

Page 27

Shut Off the Main Water Supply

Turn on the nearest faucet long enough to clear the line of water.

Safety Instructions

Install the Shutoff Valve

1 Install the shutoff valve on the nearest frequently used drinking water line.

Do not overtighten or you may crush the copper tubing.

Washer

Pipe Clamp

Inlet End

2 Choose a location for the valve that is easily accessible. It is best to connect into the side of a vertical water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from

Saddle-Type

Vertical Cold Water Pipe

Operating

the water pipe.

3 Drill a 1/4″ hole in the water pipe, using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe.

4 Fasten the shutoff valve to the cold water pipe with the pipe clamp.

5 Tighten the clamp screws until the sealing washer begins to swell.

Shutoff Valve

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

Instructions Installation

Route the Copper Tubing and Connect It to the Shutoff Valve

Route the copper tubing between the cold water line and the refrigerator.

Route the tubing through a hole drilled in the wall or floor (behind the refrigerator or adjacent base cabinet) as close to the wall as possible.

Be sure there is sufficient extra tubing [about 8 feet (244 cm) coiled into 3 turns of about 10(25 cm) diameter] to allow the refrigerator to

Saddle-Type Shutoff Valve

Packing Nut

Outlet Valve

Compression Nut

Ferrule (sleeve)

move out from the wall after installation.

Place the compression nut and ferrule (sleeve) onto the end of the tubing and connect it to the shutoff valve.

Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely.

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

Instructions Troubleshooting Tips

Turn On the Water and Flush Out the Tubing

1

Turn the main water supply on and flush out the

2

Shut the water off at the water valve after about

tubing until the water is clear.

one quart (1 L) of water has been flushed

through the tubing.

27

Customer Service

Image 27
Contents Manuel d’utilisation Manual del propietarioPart No D9617P009 Pub. No -60064 11-99 JR GE & You, a Service Partnership Customer ServiceCongratulations You Are Now Part of the GE Family CFC Disposal Troubleshooting TipsOperating Instructions Installation Instructions Before You Throw Away Your Old Refrigerator or FreezerTroubleshootingTips CustomerServiceOperatingInstructions To test the freezer Testing and Adjusting TemperaturesAbout the controls on the refrigerator Freezer Control Fresh FoodR M a L Monitor and Diagnostic SystemHow to Set the Door Alarm SafetyTips Customer Service When Your Refrigerator Is First PluggedWhat the Codes Mean Filter Bypass Plug Installing the Filter CartridgeAbout the water filter cartridge About the shelves and basketsAbout the refrigerator bins and dishes About the storage drawers Safety Instructions OperatingRefrigerator Doors About storage drawer removalAbout the refrigerator doors Drawer RemovalAbout the refreshment center Refreshment Center Compartment stores frequently used itemsBottom of Frame Automatic Icemaker TroubleshootingTips CustomerServiceAbout the automatic icemaker About the ice and water dispenserTo replace Ice Storage BinImportant Facts About Your Dispenser To removeCleaning the Decorator Door Panels Care and cleaning of the refrigeratorCleaning the Outside Cleaning the InsideUnder the Refrigerator Troubleshooting Tips Preparing to MoveInstructions Installation Instructions Behind the RefrigeratorReplacing the light bulbs TroubleshootingTips InstallationInstructionsLeveling Rollers Preparing to install the refrigeratorRefrigerator Location Clearances24″ Door Alignment24″ Cabinet 701/4″ 36″ Water Electrical ″ Airspace Wall Plates 25″ 24″ Side PanelsHandle Side 19 mm Appearance PanelRefrigerator Door Trim kits and decorator panelsPanels less than 1/4″ 6 mm thick ″ 19 mm or Raised PanelWith Refreshment Center Dimensions for Custom Wood PanelsTrim kits Freezer PanelTighten the two screws on the Top Trim to 30 in-lbs torque Inserting the door panelsLoosen the Top Trim on the Freezer and Fresh Food Doors Insert the Freezer Panel and Fresh Food PanelInstall the Side Trim Secure the Side TrimTop Trim Side Tape Liner Bottom Trim Top Trim Screws Bracket Screws Buttons Slots Installing the HandlesRemoving the Handles Inserting the Door PanelsWhat You Will Need Installing the water linePower drill Before You BeginInstructions Installation Shut Off the Main Water SupplyOperating Refrigerator Connection ″ Copper Tubing Connect the Tubing to the RefrigeratorStart the Icemaker Compression NutNormal operating sounds Before you call for service…Operating Instructions Installation Instructions Problem Possible Causes What To DoOn frozen food Fresh food or freezerCompartment too warm Frost or ice crystalsWater spurting from Cube dispenser doesNot work Water dispenser doesRefrigerator Hot air from bottomWhat GE Will Not Cover Safety Instructions Operating Instructions InstallationInstructions GE Will ReplaceNSF International Standards Operating SpecificationsGeneral Installation/Operation/Maintenance Requirements Special NoticesTurbidity Contaminants State of California Department of Health ServicesTrademark/Model Designation Replacement Elements Microbiological ContaminantsCustomerService We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Page Félicitations Désormais vous faites partie de la famille GE GE et vous, un partenariat de serviceDe dépannage Service La clientèleSe débarrasser du CFC Conseils de dépannage Raccordement ÉlectriqueLes commandes du réfrigérateur Réglage des commandesMesures de sécurité Installation Service à la clientèle Conseils de dépannage Système de contrôle et de diagnosticPourquoi le voyant Warm Temp température élevée s’allume Comment régler l’alarme des portesDe sécurité MesuresFonctionnement du système de contrôle et de diagnostic System CHECK-RESET vérification etSignification des codes Dépannage La cartouche du filtre à eauLes clayettes et les paniers MesuresInstallation Dépannage Service à la clientèle Conseils deLes balconnets et les récipients Bacs à humidité réglable Les bacs de rangementSystème Quick ServeTM Bacs de rangementPortes du réfrigérateur Enlèvement des bacs de rangementLes portes du réfrigérateur Enlèvement des bacsLe Centre de rafraîchissements Pour utiliser le distributeur Machine à glaçons automatiqueLe distributeur d’eau et de glaçons Machine à glaçons automatiqueRetrait du bac Conseils de dépannage Service à la clientèleBac à glaçons Renseignements importants concernant votre distributeurEntretien et nettoyage du réfrigérateur SécuritéMesures de Départ en vacances Service à la clientèleDerrière le réfrigérateur Sous le réfrigérateurCompartiment congélateur-modèles avec distributeur Remplacement des ampoulesCompartiment réfrigérateur-lampe supérieure Compartiment congélateur-modèles sans distributeurDégagements Emplacement du réfrigérateurPréparation Alimentation en eau de la machine à glaçonsDimensions et spécifications pour les modèles «CustomStyle» La clientèle Conseils de dépannageAlignement des portes Panneau de 3/4 po 19 mm ou surélevé Ensembles de moulures et de panneaux décoratifsAvant de commencer Panneaux de moins de 1/4 po 6 mm d’épaisseurDimensions pour les panneaux de bois sur mesure Ensembles de mouluresDe dépannage Insérez les panneaux du congélateur et du réfrigérateur Installation des panneaux de porteMoulure inférieure Installez la moulure latéraleFixez la moulure latérale Moulure SupérieureVis de la moulure supérieure Vis du support Support Boutons Installation des panneaux de porteInstallation des poignées Enlèvement des poignéesInstallation de la conduite d’eau Matériel nécessairePerceuse électrique Mesures de sécurité Installez le robinet d’arrêtConseils de Ouvrez le robinet et rincez le tuyauMettez la machine à glaçons en marche Mesures de FonctionnementOuvrez le robinet d’arrêt de la conduite d’eau principale Branchez le réfrigérateurAvant d’appeler un réparateur… Sécurité Fonctionnement InstallationDe dépannage Service à la clientèle Bruits de fonctionnement normauxMesures Fonctionnement Mesures de sécurité Fonctionnement Installation Air chaud à la base du Du congélateurLa porte ne se referme Pas entièrementGarantie DU Client Numéros de service Un service satisfaisantPour les besoins particuliers Aux États-Unis Normes internationales NSF Exigences générales d’installation/opération/entretienSpécifications d’opération Avis spéciauxGE y usted, una asociación de servicio ¡Felicidades Ahora usted es parte de la familia GEAntes de deshacerse de su viejo refrigerador o congelador Solucionar problemas ServicioAl consumidor InstalaciónComo Conectar LA Electricidad Solucionar problemasLos controles del refrigerador El ajuste de los controlesSeguridad Monitor electrónico y sistema de diagnóstico Instalación Servicio al consumidor Solucionar problemasNormal brilla Cómo fijar la alarma de la puertaAl enchufar por primera vez su refrigerador Por qué brilla la luz de Warm Temp temperatura elevadaAl oprimir System CHECK-RESET Cómo funciona el monitor y el sistema de diagnósticoSignificado de los códigos Tapón de derivación del filtro El cartucho del filtro de aguaEntrepaños y canastas Instalar el cartucho del filtroPortavinos detachable Servicio al consumidor Solucionar problemasRecipientes y fuentes del refrigerador Entrepaño ajustableGavetas para guardar Solucionar problemas Servicio al consumidorPuertas del refrigerador Sacar la gaveta para guardarPuertas del refrigerador Como sacar las gavetasEl centro de refrescos Para usar el dispensador El dispositivo automático para hacer hieloEl dispensador de agua y de hielo Dispositivo automático para hacer hieloPara volver a colocar El recipiente de almacenamiento de hieloDatos importantes de su dispensador Para sacarLimpiar el interior Cuidado y limpieza del refrigeradorLimpiar el exterior Limpiar los paneles de decoración de las puertasPreparación para vacaciones Solucionar problemasAtrás del refrigerador Debajo del refrigeradorCongelador-modelos sin dispensador de hielo ProblemasReemplazo de bombillas Compartimiento de alimentos frescos-Luz superiorEspacios libres Preparación para instalar el refrigeradorSuministro de agua al dispositivo para hacer hielo Ubicación del refrigeradorAlineación de las puertas Dimensiones y especificaciones para modelos de CustomStyleConsumidor Solucionar problemas Servicio alPanel de 3/4 ″ 19 mm o panel levantado Molduras y paneles decorativosAntes de que empiece Paneles de menos de 1/4 ″ 6 mm de espesorCon dispensador MoldurasCuidado de los paneles precortados Sin dispensador Congelador Alimentos frescosMoldura superior Corte ProblemasCómo insertar los paneles de la puerta Tornillos de laMoldura inferior Instalación de la moldura lateralAsegure la moldura lateral Moldura SuperiorTornillos de la moldura superior Remoción de las manijasInserción de los paneles de la puerta Instalación de la manijasInstalación de la línea de agua Lo que se necesitaTaladro eléctrico Corte el paso de agua del abastecimiento principal Instale la llave de pasoHaga pasar el tubo de cobre y conéctelo a la llave de paso Enchufe el cable eléctrico del refrigerador Servicio al consumidor SolucionarConecte el tubo de cobre al refrigerador Abra el agua en la llave de pasoSeguridad Sonidos normales de la operaciónAntes de solicitar un servicio… Operación InstalaciónCálido Compartimiento deAlimentos frescos o Congelador demasiadoSeguridad Operación Instalación Aire caliente a la base La puerta no se cierreCorrectamente o sólo ParcialmenteDurante GE reemplazará Lo que GE no cubriráGarantidor General Electric Company. Louisville, KY Números de servicio Especificaciones de Operación Avisos EspecialesEstándares Internacionales NSF Service Satisfaction Service Telephone Numbers

TPS24PBDBS, TPX24PBDBB, TPX24PBDAA, TPX24PBDWW, TPX24PBDCC specifications

The GE TPX24PBDCC, TPX24PBDWW, TPX24PBDAA, TPX24PBDBB, and TPS24PBDBS are part of General Electric's innovative line of refrigerators that focus on energy efficiency, spacious design, and advanced technology. Each model offers unique features catering to modern households and varying individual preferences.

One of the standout characteristics of the TPX series is its ample storage capacity, designed to accommodate the needs of families by providing flexible shelving options, adjustable bins, and spacious compartments. This ensures that users can easily organize their groceries, making meal prep more convenient.

The refrigerators are equipped with GE's advanced cooling technology, which maintains optimal temperatures and humidity levels to preserve food freshness longer. This is particularly beneficial in enhancing the shelf life of fruits and vegetables, keeping them crisp and flavorful.

Energy efficiency is a prominent feature across these models. They meet Energy Star guidelines, helping to reduce electricity bills while simultaneously minimizing environmental impact. The TPX series incorporates advanced insulation materials that contribute to lower energy consumption, ensuring that the refrigerators operate efficiently even during peak usage.

In terms of user experience, the TPX24 models offer features like adjustable temperature controls and LED lighting, which enhances visibility and makes it easier for users to find items stored inside. The ice and water dispensers, available in select models, provide convenience by allowing access to chilled water and ice without opening the fridge.

Aesthetic appeal is another consideration with the TPX series. They come in various finishes, such as fingerprint-resistant stainless steel, which not only enhances their appearance but also simplifies cleaning. This feature is particularly appreciated in busy kitchens where appearance matters.

Another remarkable aspect is the integration of modern technology. Some models may offer smart features that allow users to monitor their refrigerator from their smartphones, enabling them to adjust settings, receive alerts about temperature changes, and track food inventories, thus enhancing the overall convenience and functionality of the kitchen.

Overall, the GE TPX24PBDCC, TPX24PBDWW, TPX24PBDAA, TPX24PBDBB, and TPS24PBDBS combine cutting-edge technology, ample storage, and efficient cooling to meet diverse consumer needs. They exemplify GE's dedication to innovation and consumer satisfaction in the realm of kitchen appliances.