Thermador 2327570A, KBUIT4275E Full-Overlay Custom Panels, Top Grille Panel Routing Requirements

Page 11

Top Grille Panel – Routing Requirements

Top and bottom edges of the top panel should be edge routed ¹⁄₂" (1.3 cm) and ³⁄₈" (9.5 mm), respectively. Both ends should be edge routed ⁷⁄₈" (2.2 cm) as shown.

Door Panel - Side View

 

¹⁄₄"

 

(6.35 mm)

Panel

max.

¹⁄₂" (1.3 cm)

 

min.

¹⁄₄" (6.35 mm) max.

⁷⁄₈"

(2.2 cm)

Top

Top

Grille

Grille

⁷⁄₈"

(2.2 cm)

¹⁄₄"

(6.35 mm) max.

NOTE: When creating a panel with face detail, the offsets will be hidden and must be accounted for in order to center the detail in the top grille.

 

 

 

 

 

 

¹⁄₄"

 

 

 

 

 

 

 

 

 

 

 

 

(6.35 mm) max.

¹⁄₂"

 

 

 

Top

 

 

 

(1.3 cm)

 

 

 

 

 

 

min.

 

 

 

 

 

 

Center face detail between offsets

Full-Overlay Custom Panels

Custom overlay panels allow you to blend the exterior of your refrigerator into the overall kitchen décor, and to use custom handles for additional design flexibility.

NOTE: To use full-overlay custom panels, a Trimless Trim Kit for Side by Sides is required (TRIMKITSXS). Full-overlay custom panels and handles are required but not included. Create the panels according to these specifications. You may order Thermador’s Handle Kit (HANDKIT) or select handles from another source. See the “Models” section under “Design Specifications” for additional information.

The custom panels must have backer panels attached in order to mount them to the refrigerator. It is most common to work with three panels, as shown in the following graphic: a decorative overlay panel, a ¹/" (3.18 mm) spacer panel or spacer strips and a ¹/" (6.35 mm) backer panel.

³⁄₈"

(9.5 mm)

 

 

 

 

 

 

min.

 

 

 

Bottom

 

 

 

 

 

 

 

 

 

 

¹⁄₄"

 

 

 

 

 

 

 

 

 

 

 

 

(6.35 mm) max.

 

 

 

 

 

 

Door Panels – Routing Requirements

Overlay Panel

Spacer Panel

 

 

 

 

Backer Panel

5/8" to 3/4"

 

1/4"

(15.88 to

 

1/8"

(6.35 mm)

19.05 mm)

(3.18 mm)

 

 

 

Spacer Panel

1/8"

(3.18mm)

1" minimum

(2.54 cm)

Door/Grille Trim

Offset Dimension

If an extended handle kit is used, then routing the handle side of the panels is not required. See “Handle and Door Clearances” for more information on ordering extended handles.

If the standard handle is used, rout the entire handle side of both panels 3¹⁄₄" (8.25 cm) to allow for finger clearance. Then rout the other sides 1" (2.54 cm).

Standard Handle – Top View

In some cases, your cabinet manufacturer may choose to work with one panel routed for the different dimensions. Follow these panel dimension and placement instructions to be sure that the custom overlay panels will fit properly.

IMPORTANT:

The total weight of the refrigerator door overlay panel cannot

 

exceed 50 lbs (23 kg).

The total weight of the freezer door overlay panel cannot

 

exceed 30 lbs (13.5 kg).

Handle

3¹⁄₄"

(8.25 cm) min.

¹⁄₄" (6.35 mm) max.

2" (5 cm)

min.

Hinge Side

Door

Door

Panel

Panel

1"

(2.54 cm)

The total weight of the top grille overlay panel cannot exceed

10 lbs (4.5 kg).

11

Image 11
Contents 2327570A Instructions D’INSTALLATIONTable DES Matières Table of ContentsÍndice Your safety and the safety of others are very important Refrigerator SafetyModels Side by Side Non-Dispensing Refrigerators Design SpecificationsModels Side by Side Dispensing Refrigerators Front View Product DimensionsSide View Top View42 106 cm Models Door Swing DimensionsTipping Radius Side Tipping RadiusCustom Panel Series Handle Optional Extended Door Handle and Door Clearances for Custom Panel SeriesDoor Door Panels for Dispenser Models Custom PanelsTop Grille Panel Door Panels for Non-dispenser ModelsDoor Panel Side View Full-Overlay Custom PanelsTop Grille Panel Routing Requirements Door Panels Routing RequirementsRefrigerator Refrigerator and Side Trim DimensionsStainless Steel Series Side Panels Custom Panel Series Side Panels Refrigerator Inset Installation DimensionsFlush Installation Dimensions Recessed Inset Installation DimensionsLocation Requirements Installation RequirementsTools and Parts Model Width a as shown above Electrical RequirementsRecommended Grounding Method Water Pressure Installation InstructionsWater Supply Requirements Unpack the RefrigeratorModel Reduced Tipping Radius Reduce Tipping RadiusMove the Refrigerator Into House Connect the Water Supply Install Anti-Tip BoardsTo Install Anti-tip Boards Style 2 Copper Line Connection Connecting to Water LineMove Refrigerator to Final Location Connecting to RefrigeratorPlug in Refrigerator Door Panels Install Custom PanelsLower Leveling Legs Level Refrigerator Adjust DoorsDoor Height Adjustment Door Swing Adjustment Install Side PanelInstall Base Grille Style 1 Non-Dispenser Models Style 2 Dispenser Models Complete InstallationWater System Preparation Su seguridad y la seguridad de los demás es muy importante Seguridad DEL RefrigeradorModelos Refrigeradores de dos puertas sin despachador Especificaciones DE DiseñoModelos Refrigeradores de dos puertas con despachador Vista frontal Medidas del productoVista lateral Vista superiorModelos de 42 106 cm Arco de vuelcoMedidas de oscilación de Las puertas Arco de vuelco lateralDimensiones de la agarradera Tamaño real Medida Paneles de puerta para modelos con despachador Paneles a la medidaPanel de la rejilla superior Paneles de puerta para modelos sin despachadorAgarradera común Vista superior Paneles a la medida totalmente RecubiertosRequisitos de contorneado de los paneles de la puerta Panel de la puerta Vista lateralPaneles de soporte Modelo 42 106 cm Paneles decorativos recubiertos Modelo 42 106 cmPaneles laterales de la serie de acero inoxidable Adornos laterales Requisitos DE InstalaciónPaneles laterales para la serie De paneles a la medida Piezas y herramientasModelo Anchura a como se muestra Requisitos de ubicaciónPiezas necesarias Medidas de la aberturaPresión del agua Requisitos eléctricos Requisitos del suministroDe agua Método de conexión a tierra recomendadoModelo Arco de vuelco reducido Instrucciones DE InstalaciónCómo desempacar su Refrigerador Cómo reducir el arco de vuelcoCómo instalar los tableros antivuelco Cómo hacer entrar el refrigerador en la casaCómo instalar los tableros Antivuelco Estilo 1 Conexión de la válvula de cierre Conexión del suministro de aguaConexión al refrigerador Cómo mover el refrigerador a su Ubicación finalCómo enchufar el refrigerador Baje las patas niveladorasPaneles de la puerta Cómo instalar los paneles a la medidaCómo ajustar la altura de la puerta Cómo nivelar el refrigeradorCómo ajustar las puertas Cómo ajustar la oscilación de las puertas Cómo instalar el panel lateralCómo instalar la rejilla de La base Cómo terminar la instalación Preparación del sistema De aguaVotre sécurité et celle des autres est très importante Sécurité DU RéfrigérateurModèles Réfrigérateurs côte à côte sans distributeur Spécifications DE DesignModèles Réfrigérateurs côte à côte avec distributeur Vue avant Dimensions du produitVue latérale Vue de dessusModèles de 42 106 cm Dimensions pour le pivotement Des portesRayon de basculement Rayon de basculement latéralDimensions de la poignée Taille réelle Panneau 3,2 cm Exigences dusinage du panneau de la grille supérieure Panneau de la grille supérieurePanneaux de porte pour modèles sans distributeur Panneaux de porte pour modèles avec distributeurPanneau de porte Vue latérale Panneaux de revêtement PersonnalisésExigences dusinage des panneaux de porte Poignée standard Vue supérieurePanneaux de soutien Modèle 42 106 cm Dimensions du réfrigérateur et des garnitures latéralesRéfrigérateur Panneaux de revêtement Modèle 42 106 cmPanneaux latéraux de la série de panneaux personnalisés Dimensions pour un panneau inséréDimensions pour un panneau en affleurement Dimensions pour un panneau inséré en retraitOutillage requis Exigences D’INSTALLATIONOutillage et pièces Pièces nécessairesModèle Largeur a tel quillustré ci-dessus Exigences d’emplacementDimensions de l’ouverture Méthode recommandée de mise à la terre Pression de leau Instructions D’INSTALLATIONDéballage du réfrigérateur Réduction du rayon de BasculementFaire entrer le réfrigérateur dans Le domicile Installation de planches AntibasculementStyle 1 Raccordement sur robinet darrêt Installation des planches antibasculementRaccordement à la canalisation Deau Raccordement au réfrigérateur Déplacement du réfrigérateur à Lemplacement finalBrancher le réfrigérateur Panneaux de porte Installation des panneaux PersonnalisésDéploiement des pieds de Nivellement Ajustement de la hauteur des portes Nivellement du réfrigérateurAjustement des portes Ajustement de l’ouverture des portes Installation du panneau latéralInstallation de la grille De la base Préparation du système d’eau Achever l’installationAll rights reserved 2327570A

2327570A, KBUDT4255E, KBUDT4855E, KBUDT4265E, KBUDT4875E specifications

Thermador is a name synonymous with luxury and innovation in the kitchen appliance industry. Among its premier offerings are a range of under-counter wine preservation and refrigeration units like the KBUIT4275E, KBUIT4855E, KBUDT4275E, KBUIT4255E, and others that promise to elevate both functionality and aesthetics in your home.

The KBUIT4275E and KBUIT4855E are designed with seamless integration in mind, offering a sleek, modern look that fits effortlessly into any kitchen decor. These units have adjustable shelving, allowing for customized storage options for various bottle sizes, accommodating everything from standard wine bottles to larger formats.

Featuring advanced cooling technologies, the Thermador wine units maintain optimal temperature and humidity levels, essential for preserving wine quality. With dual temperature zones available in models like the KBUIT4855E, wine enthusiasts can store both red and white wines at their ideal serving temperatures simultaneously.

One of the standout features across the KBUIT and KBUDT lines is the use of innovative whispering quiet technology, reducing noise levels to ensure that your wine storage remains a serene part of your culinary space. Additionally, their UV-blocking glass doors protect your wine from harmful light exposure, preserving its integrity for longer periods.

For those who prioritize convenience, models like the KBUDT4255E come equipped with a soft-close feature, ensuring the doors gently close without slamming, which not only adds to the longevity of the unit but also enhances the user experience.

Thermador also integrates Smart Home technology in some models, allowing users to control temperature settings through their smartphones. This kind of technological advancement appeals to tech-savvy homeowners seeking seamless connectivity in their kitchen.

The aesthetic design is equally compelling, with options for panel-ready finishes that enable these wine units to blend seamlessly with existing cabinetry, offering a custom look.

In conclusion, Thermador’s under-counter wine preservation and refrigeration units are not just appliances; they are a fusion of state-of-the-art technology, user-friendly features, and elegant design. Whether choosing the KBUIT4265E or the KBUDT4875E, wine lovers can appreciate the careful craftsmanship and attention to detail that goes into every model, ensuring an exquisite experience with wine storage and preservation.