Thermador KBUIT4855E, 2327570A Installation Requirements, Tools and Parts, Location Requirements

Page 14

Inset Installation Dimensions

1.Measure the distance from point A (as shown) to the back wall. Add ¹⁄₃₂" (0.8 mm) to this measurement to allow the side panel to fit into the trim.

2.If the panel is more than ³⁄₈" (9.5 mm) thick, rout the front edge to allow the side panel to fit into the trim.

A

Recessed Inset Installation Dimensions

1.Measure the distance from point A (as shown) to back wall.

2.Rout the front edge of the support board or attach a ³⁄₈" (9.5 mm) board to hold the panel in the cabinet side trim.

A

INSTALLATION REQUIREMENTS

Tools and Parts

IMPORTANT:

Installer: Leave Installation Instructions with the homeowner.

Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local electrical inspector’s use.

Tools needed:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Hand drill or electric drill

T27 Torx®† screwdriver

 

(properly grounded)

¹¹⁄₃₂" nut driver

 

Drill bits

³⁄₈" and ¹⁄₂" open-end

 

Adjustable wrenches (2)

 

wrenches

Phillips screwdriver

⁵⁄₃₂" Allen wrench

Small level

⁵⁄₁₆" socket wrench

Appliance dolly

Tape measure

Parts needed:

#8 x 3" (7.6 cm) or longer wood screws (6)

2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board (1 or 2)

Make custom or overlay panels or consult a qualified cabinetmaker or carpenter to make the panels. See “Design Specifications.”

If you are connecting the water line directly to copper tubing and not to a shutoff valve, you need a ferrule, a union, and a ¹⁄₄" (6.35 mm) compression fitting.

Location Requirements

The refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to enclose the refrigerator.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT:

Observe all governing codes and ordinances.

It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source.

Do not install in a location where the temperature will fall below 55°F (13°C).

Floor must support the refrigerator weight, more than 600 lbs (272 kg), door panels and contents of the refrigerator.

Ceiling height must allow for side tipping radius. See “Tipping Radius.”

Location should permit door to open fully. See “Door Swing Dimensions.”

Location must permit top grille removal. See “Opening Dimensions.”

Opening Dimensions

To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

†®TORX is a registered trademark of Textron Innovations Inc.

14

Image 14
Contents Instructions D’INSTALLATION 2327570ATable DES Matières Table of ContentsÍndice Refrigerator Safety Your safety and the safety of others are very importantDesign Specifications Models Side by Side Non-Dispensing RefrigeratorsModels Side by Side Dispensing Refrigerators Top View Product DimensionsSide View Front ViewSide Tipping Radius Door Swing DimensionsTipping Radius 42 106 cm ModelsHandle and Door Clearances for Custom Panel Series Custom Panel Series Handle Optional Extended DoorDoor Door Panels for Non-dispenser Models Custom PanelsTop Grille Panel Door Panels for Dispenser ModelsDoor Panels Routing Requirements Full-Overlay Custom PanelsTop Grille Panel Routing Requirements Door Panel Side ViewRefrigerator Refrigerator and Side Trim DimensionsStainless Steel Series Side Panels Recessed Inset Installation Dimensions Refrigerator Inset Installation DimensionsFlush Installation Dimensions Custom Panel Series Side PanelsLocation Requirements Installation RequirementsTools and Parts Model Width a as shown above Electrical RequirementsRecommended Grounding Method Unpack the Refrigerator Installation InstructionsWater Supply Requirements Water PressureModel Reduced Tipping Radius Reduce Tipping RadiusMove the Refrigerator Into House Style 2 Copper Line Connection Connecting to Water Line Install Anti-Tip BoardsTo Install Anti-tip Boards Connect the Water SupplyMove Refrigerator to Final Location Connecting to RefrigeratorPlug in Refrigerator Door Panels Install Custom PanelsLower Leveling Legs Level Refrigerator Adjust DoorsDoor Height Adjustment Door Swing Adjustment Install Side PanelInstall Base Grille Style 1 Non-Dispenser Models Style 2 Dispenser Models Complete InstallationWater System Preparation Seguridad DEL Refrigerador Su seguridad y la seguridad de los demás es muy importanteEspecificaciones DE Diseño Modelos Refrigeradores de dos puertas sin despachadorModelos Refrigeradores de dos puertas con despachador Vista superior Medidas del productoVista lateral Vista frontalArco de vuelco lateral Arco de vuelcoMedidas de oscilación de Las puertas Modelos de 42 106 cmDimensiones de la agarradera Tamaño real Medida Paneles de puerta para modelos sin despachador Paneles a la medidaPanel de la rejilla superior Paneles de puerta para modelos con despachadorPanel de la puerta Vista lateral Paneles a la medida totalmente RecubiertosRequisitos de contorneado de los paneles de la puerta Agarradera común Vista superiorPaneles decorativos recubiertos Modelo 42 106 cm Paneles de soporte Modelo 42 106 cmPaneles laterales de la serie de acero inoxidable Piezas y herramientas Requisitos DE InstalaciónPaneles laterales para la serie De paneles a la medida Adornos lateralesMedidas de la abertura Requisitos de ubicaciónPiezas necesarias Modelo Anchura a como se muestraMétodo de conexión a tierra recomendado Requisitos eléctricos Requisitos del suministroDe agua Presión del aguaCómo reducir el arco de vuelco Instrucciones DE InstalaciónCómo desempacar su Refrigerador Modelo Arco de vuelco reducidoCómo instalar los tableros antivuelco Cómo hacer entrar el refrigerador en la casaCómo instalar los tableros Antivuelco Conexión del suministro de agua Estilo 1 Conexión de la válvula de cierreBaje las patas niveladoras Cómo mover el refrigerador a su Ubicación finalCómo enchufar el refrigerador Conexión al refrigeradorCómo instalar los paneles a la medida Paneles de la puertaCómo ajustar la altura de la puerta Cómo nivelar el refrigeradorCómo ajustar las puertas Cómo ajustar la oscilación de las puertas Cómo instalar el panel lateralCómo instalar la rejilla de La base Preparación del sistema De agua Cómo terminar la instalaciónSécurité DU Réfrigérateur Votre sécurité et celle des autres est très importanteSpécifications DE Design Modèles Réfrigérateurs côte à côte sans distributeurModèles Réfrigérateurs côte à côte avec distributeur Vue de dessus Dimensions du produitVue latérale Vue avantRayon de basculement latéral Dimensions pour le pivotement Des portesRayon de basculement Modèles de 42 106 cmDimensions de la poignée Taille réelle Panneau 3,2 cm Panneaux de porte pour modèles avec distributeur Panneau de la grille supérieurePanneaux de porte pour modèles sans distributeur Exigences dusinage du panneau de la grille supérieurePoignée standard Vue supérieure Panneaux de revêtement PersonnalisésExigences dusinage des panneaux de porte Panneau de porte Vue latéralePanneaux de revêtement Modèle 42 106 cm Dimensions du réfrigérateur et des garnitures latéralesRéfrigérateur Panneaux de soutien Modèle 42 106 cmDimensions pour un panneau inséré en retrait Dimensions pour un panneau inséréDimensions pour un panneau en affleurement Panneaux latéraux de la série de panneaux personnalisésPièces nécessaires Exigences D’INSTALLATIONOutillage et pièces Outillage requisModèle Largeur a tel quillustré ci-dessus Exigences d’emplacementDimensions de l’ouverture Méthode recommandée de mise à la terre Réduction du rayon de Basculement Instructions D’INSTALLATIONDéballage du réfrigérateur Pression de leauInstallation de planches Antibasculement Faire entrer le réfrigérateur dans Le domicileStyle 1 Raccordement sur robinet darrêt Installation des planches antibasculementRaccordement à la canalisation Deau Raccordement au réfrigérateur Déplacement du réfrigérateur à Lemplacement finalBrancher le réfrigérateur Panneaux de porte Installation des panneaux PersonnalisésDéploiement des pieds de Nivellement Ajustement de la hauteur des portes Nivellement du réfrigérateurAjustement des portes Ajustement de l’ouverture des portes Installation du panneau latéralInstallation de la grille De la base Achever l’installation Préparation du système d’eau2327570A All rights reserved

2327570A, KBUDT4255E, KBUDT4855E, KBUDT4265E, KBUDT4875E specifications

Thermador is a name synonymous with luxury and innovation in the kitchen appliance industry. Among its premier offerings are a range of under-counter wine preservation and refrigeration units like the KBUIT4275E, KBUIT4855E, KBUDT4275E, KBUIT4255E, and others that promise to elevate both functionality and aesthetics in your home.

The KBUIT4275E and KBUIT4855E are designed with seamless integration in mind, offering a sleek, modern look that fits effortlessly into any kitchen decor. These units have adjustable shelving, allowing for customized storage options for various bottle sizes, accommodating everything from standard wine bottles to larger formats.

Featuring advanced cooling technologies, the Thermador wine units maintain optimal temperature and humidity levels, essential for preserving wine quality. With dual temperature zones available in models like the KBUIT4855E, wine enthusiasts can store both red and white wines at their ideal serving temperatures simultaneously.

One of the standout features across the KBUIT and KBUDT lines is the use of innovative whispering quiet technology, reducing noise levels to ensure that your wine storage remains a serene part of your culinary space. Additionally, their UV-blocking glass doors protect your wine from harmful light exposure, preserving its integrity for longer periods.

For those who prioritize convenience, models like the KBUDT4255E come equipped with a soft-close feature, ensuring the doors gently close without slamming, which not only adds to the longevity of the unit but also enhances the user experience.

Thermador also integrates Smart Home technology in some models, allowing users to control temperature settings through their smartphones. This kind of technological advancement appeals to tech-savvy homeowners seeking seamless connectivity in their kitchen.

The aesthetic design is equally compelling, with options for panel-ready finishes that enable these wine units to blend seamlessly with existing cabinetry, offering a custom look.

In conclusion, Thermador’s under-counter wine preservation and refrigeration units are not just appliances; they are a fusion of state-of-the-art technology, user-friendly features, and elegant design. Whether choosing the KBUIT4265E or the KBUDT4875E, wine lovers can appreciate the careful craftsmanship and attention to detail that goes into every model, ensuring an exquisite experience with wine storage and preservation.