GE 197D4613P004 Installing the beverage center/wine chiller, Safety Instructions

Page 4

Safety Instructions

Installing the beverage center/wine chiller.

Removing the Packaging

Before using the beverage center/wine chiller, be sure all packing materials and tape have been removed, including the protective film covering the control and any film protecting the cabinet.

If you are discarding an old refrigeration product, remove the doors to reduce the danger of children being trapped inside.

Operating Instructions

Installation Guidelines

■The beverage center/wine chiller can be freestanding or can be installed under the counter, with proper clearances.

■Allow the following clearances for ease of installation, proper air circulation and electrical connections:

Each side

1/2″ (12,7 mm)

Top

2″ (51 mm)

Back

2″ (51 mm)

■Before connecting the appliance

to the power source, let it stand upright for approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.

■Do not install the beverage center/ wine chiller where the temperature will go below 55°F (12,7°C) or above 90°F (32,2°C). If the room temperature is below the temperature setting, the beverage center/wine chiller will not operate (for instance, if the room is at 55°F (12,7°C) and the setting is 60°F (15,6°C), the unit will not run).

■Install it on a level floor.

■Do not install the beverage center/wine chiller where it will be subject to direct sunlight, heat or moisture.

■Do not store or install this appliance outdoors.

Care and Cleaning

Troubleshooting

Tips

Consumer Support

Leveling Legs

Adjustable legs at the front corners of the beverage center/wine chiller should be set so the beverage center/ wine chiller is firmly positioned on the floor, with a 1/8″ tilt to the back to help the door closure.

To adjust the leveling legs, turn the legs

To raise the appliancecounterclockwise to raise the beverage center/wine chiller, clockwise to lower it.

Door Handle

The door handle and screws are shipped in a hardware bag attached to one

of the shelves inside the cabinet.

 

Locate the door handle and two screws.

Screw

Secure the door handle to the side

of the door as shown.

 

Door

Handle

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Beverage Center and Wine Chiller Write the model and serial numbers here Model # Serial #Safety Precautions Care and Cleaning Troubleshooting Tips Consumer SupportUSE of Extension Cords Operating InstructionsHOW to Connect Electricity Tips Troubleshooting Consumer SupportOperating Ge.comInstalling the beverage center/wine chiller Safety InstructionsAbout the control and settings Instructions InstallationCleaning Tips Troubleshooting Consumer Support CareInstallation Instructions Care and CleaningTroubleshooting Tips Consumer Support About the interior spaceSafety Care and cleaningTips Troubleshooting Operating Troubleshooting Tips Consumer Support Event of a Power FailureReplacing the light bulb Preparing to MoveReversing the Door Before you call for service… Safety Instructions Installation Care and Cleaning OperatingTips Troubleshooting Page GE Service Protection Plus General Electric CompanyConsumer Product Ownership Registration Ownership Registration Page Instructions Operating For The Period GE Will ReplaceWhat GE Will Not Cover One YearCustomer Warranty Page Mesures DE Sécurité Mise AU Rebut Appropriée DE L’APPAREILUtilisation DE Cordons Prolongateurs Conseils de dépannageRaccordement Électrique Entretien et nettoyage Conseils de dépannageInstallation du refroidisseur à boissons et à vin Directives d’installationDéballage Pieds de mise à niveauLorsque l’appareil est branché Commandes et réglagesLampe intérieure Clayettes en bois Espace intérieurDisposition des boissons et des bouteilles de vin Entretien et nettoyage Entretien de l’extérieurEntretien de l’intérieur DégivragePréparation pour un déplacement de l’appareil Remplacement de l’ampouleLors d’une panne de courant Inversion du sens d’ouverture de la porte De sécuritéAvant de contacter un service de dépannage… Entretien et nettoyageMesures de sécurité Installation Fonctionnement Conseils de Entretien et Dépannage NettoyageGarantie DU Client Prolongation de garantie Soutien au consommateur Service de réparations800.561.3344 Soporte al consumidor Antes de desechar su antiguo refrigerador Precauciones DE SeguridadRefrigerantes USO DE Cables DE Extensión Cómo Conectar LA ElectricidadLEA Y Siga Cuidadosamente Esta Información DE Seguridad Operación Cuidado y limpiezaLimpieza Operación Cómo instalar el centro de bebidas y enfriador de vinosCuidado y Acerca de los controles y ajustes LimpiezaAl conectar el centro de bebidas y enfriador de vinos Luz interiorSobre el espacio interior Cuidado y limpiezaEstantes de madera Carga de vino y de bebidasCuidado y limpieza Limpieza del exteriorLimpieza del interior DescongelaciónEn el evento de una falla de energía Cómo reemplazar la bombillaCómo prepararse para un traslado Cómo invertir el vaivén de la puerta Antes de solicitar un servicio… Cuidado y limpieza OperaciónProblemas Solucionar Notas Operación SolucionarLo que GE no cubrirá Por el período de GE reemplazaráUn año Soporte al consumidor Página Web de GE Appliances Solicite una reparaciónGarantías ampliadas Piezas y accesoriosSchedule Service Consumer Support

197D4613P004 specifications

The GE 197D4613P004 is a highly advanced component designed for specific industrial applications, particularly in the realm of power generation and distribution systems. This electronic device is recognized for its robustness, reliability, and exceptional performance under demanding conditions.

One of the main features of the GE 197D4613P004 is its versatility, as it can be integrated into various systems, including those used in turbines, generators, and other key components in the energy sector. The device is engineered to provide accurate monitoring, control, and protection for these systems, ensuring optimal performance and safety.

The technology behind the GE 197D4613P004 includes state-of-the-art microprocessor-based control systems. This allows for real-time data processing and analysis, enhancing the capability to respond to dynamic operational conditions. The microprocessor also enables advanced communication protocols, ensuring seamless interaction with other devices and systems within the network.

In terms of characteristics, the GE 197D4613P004 is built to withstand harsh environments. It features a rugged housing that protects against dust, moisture, and vibration, making it suitable for installation in challenging locations. Furthermore, the device is designed with fail-safe mechanisms, which contribute to its reliability and longevity, critical factors in industrial applications where downtime can result in significant financial losses.

Additionally, the GE 197D4613P004 supports various input and output configurations, accommodating a wide range of sensors and actuators. This flexibility enables it to tailor its functionality to specific operational requirements. With built-in diagnostics and troubleshooting capabilities, the device simplifies maintenance procedures, allowing for quicker identification of issues and reducing the risk of unexpected failures.

In conclusion, the GE 197D4613P004 stands out for its combination of advanced technology and rugged design, making it a preferred choice for professionals in the power generation and distribution sectors. Its ability to provide precise control and monitoring, along with its adaptability to various systems, makes it a vital component in enhancing operational efficiency and reliability in challenging industrial environments.
Top Page Image Contents