GE 197D4613P004 Replacing the light bulb, Operating Troubleshooting Tips Consumer Support

Page 8

Instructions

Care and cleaning.

Safety

In the Event of a Power Failure

If the power fails, open the door as infrequently as possible to maintain the temperature. A gradual rise in temperature should not have any adverse effect on the wine.

If it is extremely hot, you may want to unload the wine from the beverage center/wine chiller and move the wine

to a cooler location until power is restored.

The controls may maintain your temperature settings when the power has been restored. If your settings are not correct, reset according to the Control Settings section.

Instructions

Care and Cleaning

Operating

Troubleshooting

Tips

Consumer Support

Preparing to Move

Unload the wine, then secure the racks by

Be sure the beverage center/wine chiller

taping them in place to prevent damage.

stays in an upright position during the move.

Replacing the light bulb.

Unplug the beverage center/wine chiller.

Remove any beverages and shelves as needed for access.

The light bulb is located behind a light shield in the ceiling of the beverage center/wine chiller near the back. To remove the light shield, remove the screw on the right side of the light shield.

Pull down on the back of the light shield to release the two front tabs.

Light Shield

Unscrew the light bulb from the socket.

Screw

Replace with a 15 watt, 120 volt bulb. This type of bulb is available at most hardware and automotive parts stores.

WARNING: Using a bulb rated higher than 15 watts may damage the electronic controls on the beverage center/wine chiller.

Reinstall the light shield.

Replace the top shelf and beverages.

Plug in the beverage center/wine chiller.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Beverage Center and Wine Chiller Write the model and serial numbers here Model # Serial #Safety Precautions Care and Cleaning Troubleshooting Tips Consumer SupportUSE of Extension Cords Operating InstructionsHOW to Connect Electricity Tips Troubleshooting Consumer SupportOperating Ge.comInstalling the beverage center/wine chiller Safety InstructionsAbout the control and settings Instructions InstallationCleaning Tips Troubleshooting Consumer Support CareInstallation Instructions Care and CleaningTroubleshooting Tips Consumer Support About the interior spaceTips Troubleshooting Care and cleaningSafety Operating Troubleshooting Tips Consumer Support Event of a Power FailureReplacing the light bulb Preparing to MoveReversing the Door Before you call for service… Safety Instructions Installation Care and Cleaning OperatingTips Troubleshooting Page GE Service Protection Plus General Electric CompanyConsumer Product Ownership Registration Ownership Registration Page Instructions Operating For The Period GE Will ReplaceWhat GE Will Not Cover One YearCustomer Warranty Page Mesures DE Sécurité Mise AU Rebut Appropriée DE L’APPAREILUtilisation DE Cordons Prolongateurs Conseils de dépannageRaccordement Électrique Entretien et nettoyage Conseils de dépannageInstallation du refroidisseur à boissons et à vin Directives d’installationDéballage Pieds de mise à niveauLampe intérieure Commandes et réglagesLorsque l’appareil est branché Disposition des boissons et des bouteilles de vin Espace intérieurClayettes en bois Entretien et nettoyage Entretien de l’extérieurEntretien de l’intérieur DégivrageLors d’une panne de courant Remplacement de l’ampoulePréparation pour un déplacement de l’appareil Inversion du sens d’ouverture de la porte De sécuritéAvant de contacter un service de dépannage… Entretien et nettoyageMesures de sécurité Installation Fonctionnement Conseils de Entretien et Dépannage NettoyageGarantie DU Client 800.561.3344 Soutien au consommateur Service de réparationsProlongation de garantie Soporte al consumidor Refrigerantes Precauciones DE SeguridadAntes de desechar su antiguo refrigerador USO DE Cables DE Extensión Cómo Conectar LA ElectricidadLEA Y Siga Cuidadosamente Esta Información DE Seguridad Operación Cuidado y limpiezaCuidado y Cómo instalar el centro de bebidas y enfriador de vinosLimpieza Operación Acerca de los controles y ajustes LimpiezaAl conectar el centro de bebidas y enfriador de vinos Luz interiorSobre el espacio interior Cuidado y limpiezaEstantes de madera Carga de vino y de bebidasCuidado y limpieza Limpieza del exteriorLimpieza del interior DescongelaciónCómo prepararse para un traslado Cómo reemplazar la bombillaEn el evento de una falla de energía Cómo invertir el vaivén de la puerta Antes de solicitar un servicio… Cuidado y limpieza OperaciónProblemas Solucionar Notas Operación SolucionarUn año Por el período de GE reemplazaráLo que GE no cubrirá Soporte al consumidor Página Web de GE Appliances Solicite una reparaciónGarantías ampliadas Piezas y accesoriosSchedule Service Consumer Support

197D4613P004 specifications

The GE 197D4613P004 is a highly advanced component designed for specific industrial applications, particularly in the realm of power generation and distribution systems. This electronic device is recognized for its robustness, reliability, and exceptional performance under demanding conditions.

One of the main features of the GE 197D4613P004 is its versatility, as it can be integrated into various systems, including those used in turbines, generators, and other key components in the energy sector. The device is engineered to provide accurate monitoring, control, and protection for these systems, ensuring optimal performance and safety.

The technology behind the GE 197D4613P004 includes state-of-the-art microprocessor-based control systems. This allows for real-time data processing and analysis, enhancing the capability to respond to dynamic operational conditions. The microprocessor also enables advanced communication protocols, ensuring seamless interaction with other devices and systems within the network.

In terms of characteristics, the GE 197D4613P004 is built to withstand harsh environments. It features a rugged housing that protects against dust, moisture, and vibration, making it suitable for installation in challenging locations. Furthermore, the device is designed with fail-safe mechanisms, which contribute to its reliability and longevity, critical factors in industrial applications where downtime can result in significant financial losses.

Additionally, the GE 197D4613P004 supports various input and output configurations, accommodating a wide range of sensors and actuators. This flexibility enables it to tailor its functionality to specific operational requirements. With built-in diagnostics and troubleshooting capabilities, the device simplifies maintenance procedures, allowing for quicker identification of issues and reducing the risk of unexpected failures.

In conclusion, the GE 197D4613P004 stands out for its combination of advanced technology and rugged design, making it a preferred choice for professionals in the power generation and distribution sectors. Its ability to provide precise control and monitoring, along with its adaptability to various systems, makes it a vital component in enhancing operational efficiency and reliability in challenging industrial environments.
Top Page Image Contents