Beverage-Air 3311 manual Tight. Do not use tools to tighten knobs

Page 11
Figure U Re-assemble rotary
half of seal as shown

Disassembly and Cleaning (cont.)

4.Remove stationary half of the shaft seal assembly from the back end of the freezer cylinder. This is accomplished by reaching into the cylinder and pulling seal out with your index finger. (See Figure R)

5.Slide the rotary half of the seal off the dasher shaft. Inspect both seal components carefully for nicks or cracks. Replace seal if defective.

NOTE: To prevent leakage the surfaces of the rotary seal and the stationary seal must be smooth with no chips or cracks.

NOTE: All units are shipped with a standard ceramic seal (Part # W0340201) unless otherwise specified. Certain products contain coconut oil which requires a different sealing material. For these products use the coconut oil seal (Part # W0340210). The stationary half of the standard seal has a white polished surface. The stationary half of the coconut oil seal has a glossy black surface.

6.Remove carb tube from bottom of hopper and remove o-rings. (See Figure S).

7.Remove drip tray and empty contents.

8.Take all components to the cleaning area.

9.Prepare 1 gallon solution of hot tap water and a good grade of dishwashing detergent.

10.Thoroughly wash all components in a warm, mild detergent solution including the inside of the freezing cylinder and the mix storage hopper. DO NOT WASH COMPONENTS IN A DISHWASHER.

11.Use a medium sized brush to clean the bottom of the valve body and the inside of the plunger bore with detergent solution taking care to remove only remaining lubricant. (Figure T)

12.The exterior of the freezer should be cleaned as needed with a cloth towel.

CAUTION: Coarse rags, abrasive cleaners and excessive force can ! damage and/or scratch the surfaces of the freezer.

Figure R Installing the stationary half of seal

Figure S Carb Tube

Reassembly

 

NOTE: Allow all parts to dry completely before reassembly.

 

1. Reassemble drip tray and re-install on front of unit.

Figure T Clean Valve Body

 

2.Wet the inner rubber lip of the rotary half of the seal and the back end of

the dasher shaft with water. Slide rotary half of assembly onto the dasher shaft, RUBBER FIRST, with the smooth sealing surface facing the back of the dasher. (See Figure U). Be sure the rotary half is fully seated against the shoulder of the shaft.

3.Insert the stationary half of the seal into the ribbed rubber boot with the

polished surface facing out (forward). 4. Lightly lubricate the ribbed rubber boot of the stationary ceramic seal (taking care

not to get any lubricant on the polished surface) and insert it straight back into the recess at the back of the freezing cylinder, RUBBER FIRST. (See Figure V)

NOTE: The stationary half of the seal must be completely dry before reassembling. If the circular half of the seal is white, make sure that the grooved side is toward the rubber. If the circular half is black, be sure the glossy side is facing out.

5.Reassemble the dasher assembly, as shown in Figure W. Insert the larger front and smaller rear white plastic bearings into dasher, then slip in the stator rod.

6.Carefully and slowly guide the dasher into the freezing cylinder, taking care not to damage the seal assembly. Turn dasher shaft until it engages the square

drive coupling. Slide the dasher back into the cylinder so that the two smooth

Figure V Installing the

sealing surfaces meet. (See Figure X)

 

stationary half seal

7. Inspect and lightly lubricate the large square o-ring

 

 

and refit it into the back of the valve block

 

 

assembly. Install the valve assembly on the front

 

 

studs and tighten the knobs until they are finger

 

 

tight. Do not use tools to tighten knobs.

 

 

NOTE: Failure to lightly lubricate the large o-ring can

 

 

result in product leakage.

 

 

Figure W Dasher Assembly

Figure X Seal Assembly

 

 

 

 

Model 3311

Page 9

 

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model 3311 Beverage Freezer Manual Page Table of Contents Product Tips OPERATOR’S Safety PrecautionsFreezer Application and Specifications ModelMix Considerations General Carburetor AssemblyFreezer Specifications Shipment Transit InstallationReview hopper contents to make sure all parts are available Mix Low Function Operation and AdjustmentsAccessory Installation How to OperateFigure J Consistency AdjustmentDrain and Rinse Care and CleaningDisassembly and Cleaning Tight. Do not use tools to tighten knobs Figure CC Insert Retaining Pin Sanitizing and RefillingParts Replacement Schedule MaintenanceClean-In-Place Procedure Daily Cleaning Suggested Daily MaintenancePreventative Maintenance Procedure Every 6 to 12 Months How to Change Back Lit Sign Merchandiser Bulb How to Clean Exposed Filter Air-Cooled Unit OnlyHow to Clean Concealed Filter Air-Cooled Unit Only How to Adjust BeltProblem Probable Cause Remedy General TroubleshootingCheck List Item no Description Exploded View Model 115V Air-Cooled ModelPart Number Description Exploded View Model 220V Air-Cooled ModelExploded View Model 115V Water-Cooled Model Part Description Number Model Base Assembly 115V Air-Cooled ModelPart Number Description Model Base Assembly 220V Air-Cooled ModelModel Base Assembly 115V Water-Cooled Model Model Electrical Box Assembly 115V Model AC/WC Units Model Electrical Box Assembly 220V Air-Cooled Model Model Wiring Diagram 115V Air-Cooled Model Model Wiring Diagram 220V Air-Cooled Model Model Wiring Diagram Water-Cooled Model Model 3311 Compressor Wiring Model Ladder Diagram 115V Air-Cooled Model Model Ladder Diagram 220V Air-Cooled Model Model Ladder Diagram 115V Water-Cooled Model Model 3311 AC/WC Units Spinner Hook-Up 115V Model 220V Model Model Refrigeration 115V Air-Cooled Model Model Refrigeration 220V Air-Cooled Model Model Refrigeration 115V Water-Cooled Model Model Refrigeration Schematic AC Units 115V & 220V Models Model Refrigeration Schematic Water-Cooled Model Model Grindmaster Corporation Form # WH-312-02 W0600110

3311 specifications

The Beverage-Air 3311 is a top-tier commercial refrigerator meticulously designed to meet the demanding needs of foodservice establishments. Known for its reliability and efficiency, this model is a favorite among restaurant owners, bars, and cafés. The primary focus of the Beverage-Air 3311 is to provide optimal storage conditions for beverages, including soft drinks, juice, and bottled water, ensuring they are kept at ideal temperatures for maximum freshness.

One of the standout features of the Beverage-Air 3311 is its spacious interior, which provides ample storage for a variety of beverages. Measuring 33 inches wide, this unit can accommodate multiple shelves, each adjustable to suit the specific height requirements of various bottles and containers. The unit typically comes with sturdy, epoxy-coated wire shelves that not only ensure uniform cooling but also provide resistance against spills and easy cleaning.

Equipped with a powerful refrigeration system, the Beverage-Air 3311 utilizes environmentally friendly refrigerants, aligning with modern standards for sustainability. The compressor is designed for efficiency, providing rapid cooling and maintaining consistent temperatures across the unit while minimizing energy consumption. This feature is particularly valuable for businesses aiming to reduce operating costs while maintaining high product quality.

The Beverage-Air 3311 also includes a self-closing door with magnetic gaskets, which helps maintain the internal temperature and prevents cold air loss, thereby enhancing energy efficiency. Additionally, the doors are equipped with locks to ensure the security of valuable beverages during off-hours.

For enhanced visibility, the Beverage-Air 3311 can feature a glass door option, allowing customers and staff to easily view the stored products without opening the door. This feature not only improves accessibility but also adds an aesthetic appeal to the display.

In terms of durability, the exterior of the Beverage-Air 3311 is crafted from high-quality stainless steel, providing resistance against rust and corrosion while ensuring an easy-to-clean surface. The interior is designed with seamless construction, which further reduces the chances of bacteria buildup and makes maintenance straightforward.

Overall, the Beverage-Air 3311 combines advanced technology with thoughtful design features, making it an ideal choice for those looking to enhance their beverage service. With its capacity, efficiency, and durability, this commercial refrigerator stands out as a reliable partner in the fast-paced environment of food and beverage service.
Top Page Image Contents