Beverage-Air 3311 manual Maintenance, Clean-In-Place Procedure Daily Cleaning

Page 13

Clean-In-Place Procedure (Daily Cleaning)

This equipment has been approved for a Clean-In-Place procedure that does not require complete disassembly on a daily basis. The unit still requires regular complete disassembly for cleaning and sanitizing. To perform the C-I-P procedure follow the instruction below:

1.Empty any product in the machine and turn to OFF.

2.Disassemble the dispensing valve assembly following the instructions in Disassembly and Cleaning. NOTE: Leave the valve block in place. Only disassemble the plunger, handle, spring, o-rings and pin.

3.Remove carburetor assembly from hopper and remove o-rings.

4.Take all components to the cleaning area.

5.Carefully inspect the o-rings for cracks, chips or cuts and replace if necessary.

6.Prepare 1 gallon solution of hot tap water and a good grade of dishwashing detergent.

7.Thoroughly wash all parts including handle, pin, valve plunger, spring, carburetor assembly and all o-rings in detergent solution.

8.Use a medium sized brush to clean the bottom of the valve body and the inside of the plunger bore with detergent solution taking care to remove any remaining lubricant.

9.Reassemble following the instructions under Sanitizing and Refilling.

NOTE: Run the unit with sanitizer on “CLEAN” for 20 minutes before draining and refilling.

MAINTENANCE

!WARNING: Disconnect power for maintenance. Do not attempt to perform maintenance on the freezer until electrical power has been disconnected.

Suggested Daily Maintenance

1.Clean, lubricate and sanitize the freezer following guidelines.

2.Clean the exterior of the freezer using a soft wet cloth. (Wipe down spinner if attached)

3.Empty drip tray.

Parts Replacement Schedule

Part

Monthly

Every 3

Every 6

Annually

Quantities to

Description

Months

Months

be Replaced

 

 

Shaft Seal

 

 

 

Replace

1

(W0340201 or W0340210)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Drive Shaft

 

 

 

Inspect & replace if

1

(W0451067)

 

 

 

necessary

 

 

 

 

 

 

 

 

 

 

Drive Belts

 

 

 

Inspect & replace if

1

(W0450209)

 

 

 

necessary

 

 

 

 

 

 

 

 

 

 

Scraper blades on dasher

 

 

 

 

 

(if equipped)

 

 

Replace

 

2

(W1431084)

 

 

 

 

 

 

 

 

 

 

 

Square cut o-ring on valve

 

 

 

Inspect & replace if

 

body/face plate

 

 

 

1

 

 

 

necessary

(W0340055)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Front stator flange bearing

 

 

 

Replace

1

(W0430032)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Rear stator flange bearing

 

 

 

Replace

1

(W0430024)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Thick Product

Dispense valve o-rings

 

Replace

 

 

Plunger: 2

(W0340022)

 

 

 

Standard Product

 

 

 

 

 

 

 

 

 

Plunger: 3

Carb tube o-rings

 

Replace

 

 

2 or 3

(W0340011)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Condenser

Inspect & clean

 

 

 

1

if necessary

 

 

 

 

(Air-cooled units only)

 

 

 

 

 

 

 

 

 

 

Refer to the Crathco Parts Price List when ordering the above parts

Model 3311

Page 11

 

 

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model 3311 Beverage Freezer Manual Page Table of Contents Freezer Application and Specifications OPERATOR’S Safety PrecautionsModel Product TipsFreezer Specifications Carburetor AssemblyMix Considerations General Shipment Transit InstallationReview hopper contents to make sure all parts are available Accessory Installation Operation and AdjustmentsHow to Operate Mix Low FunctionFigure J Consistency AdjustmentDisassembly and Cleaning Care and CleaningDrain and Rinse Tight. Do not use tools to tighten knobs Figure CC Insert Retaining Pin Sanitizing and RefillingClean-In-Place Procedure Daily Cleaning MaintenanceSuggested Daily Maintenance Parts Replacement SchedulePreventative Maintenance Procedure Every 6 to 12 Months How to Clean Concealed Filter Air-Cooled Unit Only How to Clean Exposed Filter Air-Cooled Unit OnlyHow to Adjust Belt How to Change Back Lit Sign Merchandiser BulbProblem Probable Cause Remedy General TroubleshootingCheck List Item no Description Exploded View Model 115V Air-Cooled ModelPart Number Description Exploded View Model 220V Air-Cooled ModelExploded View Model 115V Water-Cooled Model Part Description Number Model Base Assembly 115V Air-Cooled ModelPart Number Description Model Base Assembly 220V Air-Cooled ModelModel Base Assembly 115V Water-Cooled Model Model Electrical Box Assembly 115V Model AC/WC Units Model Electrical Box Assembly 220V Air-Cooled Model Model Wiring Diagram 115V Air-Cooled Model Model Wiring Diagram 220V Air-Cooled Model Model Wiring Diagram Water-Cooled Model Model 3311 Compressor Wiring Model Ladder Diagram 115V Air-Cooled Model Model Ladder Diagram 220V Air-Cooled Model Model Ladder Diagram 115V Water-Cooled Model Model 3311 AC/WC Units Spinner Hook-Up 115V Model 220V Model Model Refrigeration 115V Air-Cooled Model Model Refrigeration 220V Air-Cooled Model Model Refrigeration 115V Water-Cooled Model Model Refrigeration Schematic AC Units 115V & 220V Models Model Refrigeration Schematic Water-Cooled Model Model Grindmaster Corporation Form # WH-312-02 W0600110

3311 specifications

The Beverage-Air 3311 is a top-tier commercial refrigerator meticulously designed to meet the demanding needs of foodservice establishments. Known for its reliability and efficiency, this model is a favorite among restaurant owners, bars, and cafés. The primary focus of the Beverage-Air 3311 is to provide optimal storage conditions for beverages, including soft drinks, juice, and bottled water, ensuring they are kept at ideal temperatures for maximum freshness.

One of the standout features of the Beverage-Air 3311 is its spacious interior, which provides ample storage for a variety of beverages. Measuring 33 inches wide, this unit can accommodate multiple shelves, each adjustable to suit the specific height requirements of various bottles and containers. The unit typically comes with sturdy, epoxy-coated wire shelves that not only ensure uniform cooling but also provide resistance against spills and easy cleaning.

Equipped with a powerful refrigeration system, the Beverage-Air 3311 utilizes environmentally friendly refrigerants, aligning with modern standards for sustainability. The compressor is designed for efficiency, providing rapid cooling and maintaining consistent temperatures across the unit while minimizing energy consumption. This feature is particularly valuable for businesses aiming to reduce operating costs while maintaining high product quality.

The Beverage-Air 3311 also includes a self-closing door with magnetic gaskets, which helps maintain the internal temperature and prevents cold air loss, thereby enhancing energy efficiency. Additionally, the doors are equipped with locks to ensure the security of valuable beverages during off-hours.

For enhanced visibility, the Beverage-Air 3311 can feature a glass door option, allowing customers and staff to easily view the stored products without opening the door. This feature not only improves accessibility but also adds an aesthetic appeal to the display.

In terms of durability, the exterior of the Beverage-Air 3311 is crafted from high-quality stainless steel, providing resistance against rust and corrosion while ensuring an easy-to-clean surface. The interior is designed with seamless construction, which further reduces the chances of bacteria buildup and makes maintenance straightforward.

Overall, the Beverage-Air 3311 combines advanced technology with thoughtful design features, making it an ideal choice for those looking to enhance their beverage service. With its capacity, efficiency, and durability, this commercial refrigerator stands out as a reliable partner in the fast-paced environment of food and beverage service.
Top Page Image Contents