Beverage-Air 3311 manual Installation, Shipment Transit

Page 6

INSTALLATION

Shipment Transit

1.The freezer has been operated and tested at the factory. Upon arrival the complete freezer must be thoroughly checked for any damage which may have occurred in transit.

Note: A Tip (N) Tell warning device is placed on each shipping carton at the factory. If the indicator is red, the carton has been tipped in transit. (See Figure B)

2.THE CARRIER IS RESPONSIBLE FOR ALL DAMAGE IN TRANSIT WHETHER VISIBLE OR CONCEALED. DO NOT PAY THE FREIGHT BILL until the freezer has been checked for damage. Have the carrier note any visible damage on the freight bill. If concealed damage and/or shortages are found later, advise the carrier within 10 days and request inspection. The customer must place any claim for damage and/or shortage with the carrier. Grindmaster cannot make any claims against the carrier.

Installing Your Unit

1.Place the self-sealing rubber pad (shipped with the freezer) on a level counter that is stable and strong enough to safely support the freezer’s weight (200 lbs / 90.7 kg), or if equipped with legs instead of pad, install legs by screwing them into the four leg holes on the bottom of the unit. (Leg Kit Part # W0890220 (4) 4” Legs)

2.Make sure freezer is to be placed in a location that is within 6’ of a properly grounded circuit and allows adequate space at each side and above for proper air circulation. Air Cooled Units Only: Minimum clearance is 6” (15 cm) on both sides and 0” at back and open above the freezer. (See Figure C)

Water Cooled Units Only: 3 - 6” of clearance are required at the rear of the unit, 0” of clearance are required on both sides and open at top.

NOTE: Failure to allow adequate ventilation will void the warranty and reduce freezer performance.

NOTE: Locating the unit in high ambient temperatures (over 100°F / 37.8°C) will significantly reduce the performance of your machine.

3.Remove the side panels and supporting all four sides, lift machine up (by the frame) and place in appropriate area on top of rubber pad.

Figure B

Figure C

!

!

CAUTION: If equipped with spinner do not lift unit up by spinner shaft. It will cause serious damage to spinner.

CAUTION: Beverage freezers are heavy pieces of equipment. It is

recommended that moving or lifting the unit be done by two people toFigure D avoid injury.

4.The side panels should still be removed. Cut the cable tie used to secure motor during shipment. Make sure motor rocks freely. (Figure D)

5.Water Cooled Units Only: Hook water to inlet (3/8” flare fitting). Hook the drain line to the fitting on the out port. The out port will go to a drain or recirculating pump (reservoir with recirculating pump is recommended).

6.220V/50Hz Units: These units come with a plugless cord that requires the appropriate plug configuration be connected. This must be determined by the power outlets at the specified location. See wiring diagram at back of manual for assistance. It is recommended that a service technician performs this operation.

Page 4

Model 3311

 

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model 3311 Beverage Freezer Manual Page Table of Contents Model OPERATOR’S Safety PrecautionsFreezer Application and Specifications Product TipsCarburetor Assembly Freezer SpecificationsMix Considerations General Installation Shipment TransitReview hopper contents to make sure all parts are available How to Operate Operation and AdjustmentsAccessory Installation Mix Low FunctionConsistency Adjustment Figure JCare and Cleaning Disassembly and CleaningDrain and Rinse Tight. Do not use tools to tighten knobs Sanitizing and Refilling Figure CC Insert Retaining PinSuggested Daily Maintenance MaintenanceClean-In-Place Procedure Daily Cleaning Parts Replacement SchedulePreventative Maintenance Procedure Every 6 to 12 Months How to Adjust Belt How to Clean Exposed Filter Air-Cooled Unit OnlyHow to Clean Concealed Filter Air-Cooled Unit Only How to Change Back Lit Sign Merchandiser BulbGeneral Troubleshooting Problem Probable Cause RemedyCheck List Exploded View Model 115V Air-Cooled Model Item no DescriptionExploded View Model 220V Air-Cooled Model Part Number DescriptionExploded View Model 115V Water-Cooled Model Model Base Assembly 115V Air-Cooled Model Part Description NumberModel Base Assembly 220V Air-Cooled Model Part Number DescriptionModel Base Assembly 115V Water-Cooled Model Model Electrical Box Assembly 115V Model AC/WC Units Model Electrical Box Assembly 220V Air-Cooled Model Model Wiring Diagram 115V Air-Cooled Model Model Wiring Diagram 220V Air-Cooled Model Model Wiring Diagram Water-Cooled Model Model 3311 Compressor Wiring Model Ladder Diagram 115V Air-Cooled Model Model Ladder Diagram 220V Air-Cooled Model Model Ladder Diagram 115V Water-Cooled Model Model 3311 AC/WC Units Spinner Hook-Up 115V Model 220V Model Model Refrigeration 115V Air-Cooled Model Model Refrigeration 220V Air-Cooled Model Model Refrigeration 115V Water-Cooled Model Model Refrigeration Schematic AC Units 115V & 220V Models Model Refrigeration Schematic Water-Cooled Model Model Grindmaster Corporation Form # WH-312-02 W0600110

3311 specifications

The Beverage-Air 3311 is a top-tier commercial refrigerator meticulously designed to meet the demanding needs of foodservice establishments. Known for its reliability and efficiency, this model is a favorite among restaurant owners, bars, and cafés. The primary focus of the Beverage-Air 3311 is to provide optimal storage conditions for beverages, including soft drinks, juice, and bottled water, ensuring they are kept at ideal temperatures for maximum freshness.

One of the standout features of the Beverage-Air 3311 is its spacious interior, which provides ample storage for a variety of beverages. Measuring 33 inches wide, this unit can accommodate multiple shelves, each adjustable to suit the specific height requirements of various bottles and containers. The unit typically comes with sturdy, epoxy-coated wire shelves that not only ensure uniform cooling but also provide resistance against spills and easy cleaning.

Equipped with a powerful refrigeration system, the Beverage-Air 3311 utilizes environmentally friendly refrigerants, aligning with modern standards for sustainability. The compressor is designed for efficiency, providing rapid cooling and maintaining consistent temperatures across the unit while minimizing energy consumption. This feature is particularly valuable for businesses aiming to reduce operating costs while maintaining high product quality.

The Beverage-Air 3311 also includes a self-closing door with magnetic gaskets, which helps maintain the internal temperature and prevents cold air loss, thereby enhancing energy efficiency. Additionally, the doors are equipped with locks to ensure the security of valuable beverages during off-hours.

For enhanced visibility, the Beverage-Air 3311 can feature a glass door option, allowing customers and staff to easily view the stored products without opening the door. This feature not only improves accessibility but also adds an aesthetic appeal to the display.

In terms of durability, the exterior of the Beverage-Air 3311 is crafted from high-quality stainless steel, providing resistance against rust and corrosion while ensuring an easy-to-clean surface. The interior is designed with seamless construction, which further reduces the chances of bacteria buildup and makes maintenance straightforward.

Overall, the Beverage-Air 3311 combines advanced technology with thoughtful design features, making it an ideal choice for those looking to enhance their beverage service. With its capacity, efficiency, and durability, this commercial refrigerator stands out as a reliable partner in the fast-paced environment of food and beverage service.
Top Page Image Contents