Multiquip WM-70P (Plastic), WM-70S (Steel) manual Suspension, Keep Hands, Mixer Storage

Page 34

WM-70 PLASTER/MORTAR MIXER — MAINTENANCE (MIXER)

Suspension

The rigid type axle and associated hardware (Figure 35) should be periodically inspected for signs of excessive wear, elon- gation of bolt holes, and loosening of fasteners. Replace all damaged parts immediately.

Figure 35. Axle Support Components

Mixer Cleaning

1.ALWAYS disconnect the spark plug wire (gasoline engines) before cleaning the inside of the drum. If mixer is equipped with an electric motor remove power cord from AC power receptacle. In addition make sure the clutch engagement lever is dis-engaged.

2.Make sure the rear section of the safety grate is connected to the mixing drum.

3.At the end of each day’s operation, place mixer drum in an upright position and spray inside of tub immediately with water to prevent lumps of dried mortar or plaster from forming and contamination of future batches, DO NOT allow a buildup of materials to form on the blades or anywhere inside the drum.

4.Rotate mixer to dump position and remove debris.

5.Thoroughly clean the entire mixer, wheels, cabinet and frame.

6.NEVER! pour or spray water over the engine or electric motor (Figure 36).

 

WARNING

Keep Hands

 

Clear of Drum!

 

 

When rotating the mixing drum from the dump position to the upright position, keep hands clear of safety grate. The possibility exists of hands or fingers being crushed (Figure 37).

Figure 37. Safety Grate (Crush Hazard)

7.When cleaning of the entire mixer is done, return mixing drum to an upright position.

Mixer Storage

For storage of the mixer for over 30 days, the following is recommended:

zDrain the fuel tank completely, or add STA-BIL to the fuel.

zRun the engine until the fuel is completely consumed.

zCompletely drain used oil from the engine crankcase and fill with fresh clean oil, then follow the procedures described in the engine manual for engine storage.

zClean the entire mixer and engine compartment.

zPlace the mixing drum in the down position (mouth facing downward).

zCover the mixer and place it a clean dry area, that is protected from harsh elements.

Figure 36. No Spraying of Water

PAGE 34 — WM-70 PLASTER/MORTAR MIXER — OPERATION MANUAL — REV. #1 (08/09/04)

Image 34
Contents Model WM-70S Steel Model WM-70P Plastic Page Heres HOW to GET Help WM-70 PLASTER/MORTAR Mixer -TABLE of Contents Direct TOLL-FREE access WM-70 PLASTER/MORTAR Mixer Specifications WM-70 PLASTER/MORTAR Mixer Dimensions Description Dimensions in. cmBurn Hazards WM-70 PLASTER/MORTAR Mixer Safety Message Alert SymbolsRespiratory Hazards WM-70 PLASTER/MORTAR Mixer Safety Message Alert Symbols Equipment DamageWM-70 PLASTER/MORTAR Mixer Rules for Safe Operation Read this manualMixer when in use Stand ClearTow Bar to Vehicle Connection Coupler Only Towing Safety Precautions Regularly InspectWM-70 PLASTER/MORTAR Mixer -TOWING Guidelines ReplacingAlways Tow with WM-70 PLASTER/MORTAR Mixer Safety Chain ConnectionWhen Towing Tow Bar to Mixer ConnectionWM-70 PLASTER/MORTAR Mixer Operation and Safety Decals Machine Safety DecalsWM-70 PLASTER/MORTAR Mixer General Information WM-70 PLASTER/MORTAR Mixer Major Components Mixer ComponentsExplosive WM-70 PLASTER/MORTAR Mixer Engine ComponentsInitial Servicing Burn HazardElectric Motor WM-70 PLASTER/MORTAR Mixer Electric MotorElectric Motor Connection Electric Motor Voltage Switch WM-70 PLASTER/MORTAR Mixer Electric MotorWM-70 Mixer Paddle Blade Adjustment Steel Drum WM-70 Mixer Paddle Blade Adjustment Poly Drum Inspection WM-70 PLASTER/MORTAR Mixer InspectionBefore Starting Engine Oil CheckWM-70 PLASTER/MORTAR Mixer Inspection Start-up ProcedureGasonline Engine WM-70 PLASTER/MORTAR Mixer START-UP ProcedureRespiratory Hazard Engine ON/OFF Switch Dump Handle Safety Mixing DumpingWM-70 PLASTER/MORTAR Mixer Operation OFF positionWM-70 PLASTER/MORTAR Mixer Maintenance Engine Engine Maintenance ScheduleMaintenance WM-70 PLASTER/MORTAR Mixer Maintenance EngineExplosive Hazard Drum Head Seals WM-70 PLASTER/MORTAR Mixer Maintenance MixerBall Socket and Clamp Face Maintenance Drum Bearing Bracket LubricationInspect Tooth Contact between Main Gear and Drive Pinion WM-70 PLASTER/MORTAR Mixer Maintenance MixerMain Gear and Drive Pinion Alignment Gear LubricationEyesight Hazard TiresWear/InflationTires/Wheels/Lug Nuts Lug NutTorque Requirements Wheel Lug NutsTightening SequenceKeep Hands SuspensionMixer Storage WM-70 PLASTER/MORTAR Mixer -TROUBLESHOOTING Engine Engine TroubleshootingWM-70 PLASTER/MORTAR Mixer -TROUBLESHOOTING Engine WhiteWM-70PLASTER/MORTARMIXER-TROUBLESHOOTINGMIXER/ELECTRICMOTOR WM-70 PLASTER/MORTAR Mixer -WIRING Diagram Electric Motor Page Multiquip INC