U-Line ADA15IM manual Leveling Information, Grille Installation

Page 17

12 Install

Leveling Information

ADA15IM & BI2115

It is recommended that the unit is level.

1. Use a level to check the levelness of the unit from front to back and from side to side. Level should be placed along top edge and side edge as shown

2. If the unit is not level, adjust

 

the feet on the corners of

1

the unit as necessary (not

 

available in all models).

Turn Foot to Adjust

3.Check the levelness after each adjustment and repeat the previous steps until the unit is level.

INSTALLATION TIP

If the room floor is higher than the floor in the cut-out opening, adjust the rear feet to achieve a total unit rear height of 1/8" less than the opening’s rear height. Shorten the unit height in the front by adjusting the front feet. This allows the unit to be gently tipped into the opening. Readjust the front feet to level the unit after it is correctly positioned in the opening.

All Other Models

IMPORTANT

It is extremely important that these units sit on a level surface, as they do not have feet levelers. If they are not level, the ice mold will not fill evenly.

Use a level to check the levelness of the unit from front to back and from side to side. Level should be placed along top edge and side edge as shown.

1

Installation

1.Open the water supply valve in the main water source.

2.Plug in the powercord.

3.Gently push the unit into position. Be careful not to kink the water supply line or entangle the electrical cord.

4.Re-check the leveling, from front to back and side to side. Make any necessary adjustments. The unit’s top surface should be approximately 1/8" below the countertop.

Grille Installation

BI95, BI98, WH95TP, BCM95BTP, BCM95

1.Locate and remove the grille screw from the cabinet, using a standard blade screwdriver (or a 1/4" nut driver).

2.Identify the grille screw hole on the grille itself. It is located toward the top of the middle recessed section of the grille.

3.Place the two hook-hinges (located on the rear bottom side of the grille) onto the front lip of the unit base. Swing the grille up into position, aligning the grille screw hole on the grille to the grille screw hole on the cabinet. See Below.

4.Insert the screw. Do not overtighten.

Grille Screw

Grille

Hook-Hinge

Unit Base

Front Lip

SS1095 Models

SS1095NF & SS1095FC models: Place the bottom lip of the grille on the inside of the base pan and swing grille up into position.

SS1095FD model: Align the tabs on the bottom of the grille with the slots in the flange and swing grille up into position.

Model:

SS109FD

Models:

SS1095NF & SS1095FC

Align Tab

With Slots

Insert This Lip Behind Base Plate Lip

Align the grille and cabinet screw holes.

Insert the grille screw and tighten. Do not over-tighten

Level & Install Unit

16

Image 17
Contents Install Guide Table of Contents Safety Precautions Safety Alert DefinitionsGeneral Precautions Product Registration Models Covered Exterior CleaningTools / Material Required Inspect & PlanPrepare Site Cut-Out DimensionsUnits can not be installed behind a closed cabinet door BI95BTP ADA15IM Series Product DimensionsADA15IM Stainless Series BI95B & BI95WH BI98 BI2115SS1095FC SS1095FDSP18 SS1095NFPower Supply Door Swing DimensionsWater Supply Environmental RequirementsReversing the Door BI95 & BI98Door Reversal See Figure WH95TP, BI95BTP, BCM95 & SP181213 16172324 SS1095Underneath the hinge to the opposite hole in top cap Page Door Panel Installation 98, SP18, & ADA15 Panel DimensionsDoor Panel Installation Door Panel PreparationElectrical Specifications Adjusting Door AlignmentAdjust Door Power SupplyPlumbing Water Supply ConnectionGrille Installation InstallationInstall Leveling InformationBI-2115 Specific Installation TroubleshootingInstallation Guide
Related manuals
Manual 2 pages 62.78 Kb Manual 66 pages 37.32 Kb