Smeg STA4645 Adding the rinse-aid, Adjusting the rinse-aid dispenser setting, User Instructions

Page 35
4.2.1Adding the rinse-aid

EN

USER INSTRUCTIONS

4.2.1Adding the rinse-aid

The rinse aid helps the dishes dry faster and prevents the formation of scale de- posits and staining; it is automatically added to the water during the fi nal rinse cycle, from the container situated on the inner side of the door.

B

A

C

Fig. 4-04

To add rinse aid:

Open the door.

Rotate the container cover (ref. A fi g. 4-04) anticlockwise by ¼ of a turn and remove it.

Add the rinse aid until the container is full (approximately 140 ml). The optical level indicator (ref. B fi g. 4-04), on the side of the cap should be completely obscured. Refi ll the rinse aid when the optical level indicator becomes clear again, or when the rinse aid warning light on the panel illuminates (see “De- scription of controls” manual).

Replace the cover (ref. A fi g. 4-04) by turning it in a clockwise direction until it is fully closed.

Use a cloth to remove any spillage of rinse aid which might lead to the forma- tion of excess foam.

4.2.2 Adjusting the rinse-aid dispenser setting

The rinse-aid dispenser can be set to one of 6 different levels. The dishwasher is factory set for medium water hardness (selector set to “3”). To change the setting, turn the dispenser selector (ref. c fi g. 4-04) to the desired position: the amount of rinse-aid dispensed is proportional to the position of this selector. Make sure that the minimum amount of rinse-aid (selector turned to “1”) is approximately 1 ml and the maximum amount (selector turned to “6”) is ap- proximately 6 ml.

18

Rev 0.0

Image 35
Contents INSTRUCTION MANUAL GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMSCONTENTS CONTENTSPage Nomenclature of figures and tables INTRODUCTION1 INTRODUCTION This symbol highlights general information and warnings Tab Symbols used in this manual see tab2 DESCRIPTION AND USE OF THE CONTROLS 2.1 Upper panel USER INSTRUCTIONSUSER INSTRUCTIONS 2.2 Setting the washing program and switching on and offLISTED ETL SANITATIONBefore starting a washing program, make sure that 2.2.1 Switching on2.2.2 Selecting and starting the program 2.2.3 End of program2.2.5 Changing the current program 2.2.6 Canceling the current program2.2.4 Interrupting a program PROGRAM DELAY 2.2.7 Options3., 4., 5., 0., 1 2.2.8 Switching off2.3.1 Adjusting the water softener 2.3 Additional functionsWATER HARDNESS Water hardness table see tab3 ENERGY SAVING AND ENVIRONMENTAL RESPECT 4 REMOVING THE DISHES 5 TROUBLESHOOTING Alarms E1, E3, E4, immediately terminate the current program Contents Page Thank you for choosing one of our products. To use this dishwasher correctly and safely, please read this manual carefully. The manual is divided into sections giving you a step-by-step guide to all your appliance’s functions. The texts are easy to understand and are complete with detailed illustrations. Following the cleaning instruc- tions provided here will keep dishwasher performance at peak levels in the long term. This user-friendly manual will provide answers to all your questions about use of the dishwasher This manual comprises the following sectionsINTRODUCTION Save this instructions 2 IMPORTANT SAFETY INSTRUCTIONWARNINGS WARNINGS ONLY USE RINSE-AID SPECIALLY FORMULATED FOR DOMESTIC DISHWASHERS DO NOT LEAN AGAINST OR STAND ON THE DISHWASHER RACKS DO NOT INTRODUCE ANIMALS INTO THE DISHWASHERATTEMPT TO REPAIR THE APPLIANCE THE MANUFACTURER DECLINES ALL RESPONSIBIL- ITY FOR DAMAGE TO PERSONS, ANIMALS OR PROPER- TY RESULTING FROM FAILURE TO OBSERVE THE ABOVE PRECAUTIONS, FROM TAMPERING WITH EVEN A SINGLE COMPONENT OF THE APPLIANCE, OR FROM THE USE OF UNORIGINAL SPARE PARTS 3 INSTALLATION AND HOOK-UP INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS add the rinse-aid and detergent 4 OPERATING INSTRUCTIONSadjust the water softening system add the regenerating salt 4.1 Using the water softening system When using the dishwasher for the fi rst time, in addition to the salt it is also necessary to add one liter of water to the container ED AS REQUIRED 4.2 Using the rinse-aid and detergent dispensers4.2.1 Adding the rinse-aid 4.2.2 Adjusting the rinse-aid dispenser setting4.2.3 Adding the detergent When a program with hot prewash is selected see program table in the “De- scription of Controls” manual, extra detergent must be placed in the cavity ref. A or B fi g. 4-06, depending on models 4.3 General warnings and recommendations Dishes and objects in copper, tin, zinc or brass these tend to stain MAKE SURE that the items being washed are dishwasher-safeItems which are not dishwasher-safe 4.4 Using the racks Con supporti fissi 4.4.1 Lower rackLoading examples Loading the lower rack see fi gEsempi di caricamento 4.4.2 Cutlery basket see fi g 4.4.3 Upper rack vedi fi g. 4-12 EsempiLoading caricamentoexamples Loading the upper rack vedi fi gAdjusting the upper rack NEVER USE ABRASIVE AND/OR CORROSIVE DETERGENTS TO CLEAN THE APPLIANCE 5 CLEANING AND USER-MAINTENANCE5.1 General warnings and recommendations Removing the spray arms 5.2 Cleaning the water intake filter only some models5.3 Cleaning the spray arms USER INSTRUCTIONS 5.4 Cleaning the filter unit 5.5 General warnings and recommendations for correct maintenance Before starting the dishwasher after prolonged disuse 5.6 Troubleshooting minor problemsIf the dishes do not come out clean, check that Prolonged disuseIf there are visible traces of rust inside the tank If the dishes fail to dry or remain dull, check thatIf the dishes show signs of streaking, staining, etc., check that 6 TECHNICAL DATA SEE TAB CONTENTS Page INTRODUCTION INTRODUCTION WARNINGS 2 SAFETY INFORMATIONREPAIR THE APPLIANCE TWO PEOPLE WEARING SAFETY GLOVES ARE REQUIRED TO LIFT THE DISHWASHERWARNINGS B A D C F E H G I L 3 INSTALLATION MATERIALINSTALLATION INSTRUCTIONS models sta4645/sta8743 INSTALLATION INSTRUCTIONS3.1 Kit supplied with dishwasher A B D E F G H I 3.2 Kit supplied with dishwasher models pla8743DIMENSIONS OF DISHWASHER See fi g Only for free-standing models 5 INSTALLATION AND HOOK-UP5.1.1 Mounting the feet only for some models 5.1 Leveling5.1.2 Levelling the appliance FIRE HAZARD DO NOT COVER OR CRUSH THE CORD PLUG 5.2 Connections5.2.1 Connecting to the water supply 5.2.1.1 Connecting to the water tap Do not cut the inlet hose see fi g min O4 cm 5.2.1.2 Connecting the drain hose Connecting to a drainMAX 100 cm 3-59/64”D fi g. 5-11 do not cut the corrugated section Connecting to a “T” union of the drain circuitConnecting to a waste disposal unit with an air gap Connecting to the air gap no waste disposal unit A D C B Connecting to a waste disposal unit no air gapGrounding instructions 5.2.2 Electrical connections and warnings5.3 Commissioning 5.3.1 Installation procedure all modelsINSTALLATION INSTRUCTIONS Mount the door panel 5.3.2 Procedure for mounting the door panelN.B. the screws are not supplied Insert the door spacers contained in the accessory bag see fi gsee fi g Attach the door panel fi t the hooks into their slots on the dishwasher and allow the panel to slide downwards and slip in to place see fi g 4.2” models pla8743 5.3.3 Procedure for mounting the door panelIf a gap is created between the control panel and the door panel ref. A fi g. 5-29, use the supplied strips ref. B fi g. 5-29 to fi ll it. The number of strips depends on the size of the gap INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 5.3.4 Completion of installation all models Remove the adhesive band on the gasket see fi g INSTALLATION INSTRUCTIONS 5.4 Testing 19 570 0074