Smeg LVS1449B Troubleshooting, User instructions, E1 E2 E3 E4 E5 E6 E7 E8 E9, Fault, Description

Page 36
6. Troubleshooting

User instructions

6. Troubleshooting

The dishwasher is equipped with a self-diagnostics system that is capable of detecting and signalling a number of possible faults.

TABLE OF FAULTS DETECTED BY THE SELF-DIAGNOSTICS SYSTEM

FAULT

E1

E2

E3

E4

E5

E6

E7

E8

E9

DESCRIPTION

The anti-flooding system (where present) has been tripped service. The water level limitation system has tripped.

The appliance cannot heat the water. The temperature sensor is disconnected. The appliance cannot take in the water.

The appliance cannot drain the water from the tank.

The dishwasher cannot measure the precise water quantity that has been loaded.

Problem on the water distribution system to the baskes. Water intake system malfunction.

The E1, E2, E3, E4, E8, E9 alarms provoke the “forcing” to end cycle of the running program.

The E5, E6 alarms interrupts the running program once the cause is resolved, it will bring bach the execution of the program.

The alarm E7 is visualized at the end of the cycle that comes, however, brought to the end since the operation of the dishwasher is not harmed.

To “reset” an alarm is necessary:

Open and close the door, or turn off and on the machine. At this point is possible to program the dishwasher again.

If the fault persists, call the authorised Technical Service Centre.

35

Image 36
Contents GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents Safety instructions 1. Safety and operating instructionsTHIS DISHWASHER MUST BE USED BY ADULTS AQUASTOP MODELS Installation instructions 2. Installation and hook-upFor free-standing models only CONNECTING TO THE WATER SUPPLY 2.1 Water supply connectionDRAIN CONNECTION 2.2 Electrical connection and precautions IF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORDFuse replacement FOR GREAT BRITAIN ONLYUser instructions 3. Description of the controls6 START/STOP BUTTON 7 POWER ON LIGHT 3.1 Front panelOnly run the soak program with half loads 3.3 Washing programs Before starting a washing program make sure thatThe correct amount of detergent has been added to the dispenser LIGHTINGSELECTION PROGRAM START PROGRAMEND PROGRAM INTERRUPTING A PROGRAMTO CHANGE A PROGRAM STOPPING A PROGRAMParticularly, on the display it will have the following indications HALF LOAD WASH FUNCTION on some models only TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENTREMOVING THE DISHES 4. Operating instructions 4.1 Using the water softening systemUser instructions 4.2 Using the rinse aid and detergent dispensers WATER HARDNESS TABLEADJUSTING THE RINSE AID DISPENSER SETTING ADDING THE RINSE AIDADDING THE DETERGENT During the washing cycle, the dispenser will be opened automaticallyUser instructions 4.3 General warnings and recommendations Correct loading of the dishes helps ensure optimal washing resultsMAKE SURE that the items being washed are dishwasher-safe Items which are not dishwasher-safe Dishes and objects in copper, tin, zinc or brass these tend to stain4.4 Using the baskets LOWER BASKETLOADING THE LOWER BASKET Loading examples ½ LOADCUTLERY BASKET UPPER BASKET LOADING THE UPPER BASKETADJUSTING THE UPPER BASKET Version BUser instructions 5. Cleaning and maintenance CLEANING THE WATER INTAKE FILTERCLEANING THE SPRAY ARMS 5.1 General warnings and recommendationsCLEANING THE FILTER UNIT GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCEPROLONGED DISUSE Fill the rinse aid dispenser Shut off the water supply tapTROUBLESHOOTING MINOR PROBLEMS If the dishes are not being cleaned properly, check thatBEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE Reconnect the water intake hose and open the tap againIf the dishes fail to dry or remain dull, check that If the dishes show signs of streaking, staining, etc., check thatIf there are visible traces of rust inside the tank 6. Troubleshooting TABLE OF FAULTS DETECTED BY THE SELF-DIAGNOSTICS SYSTEMFAULT E1 E2 E3 E4 E5 E6 E7 E8 E9TECHNICAL DATA Electrical characteristicsWidth Capacitymollelaterali primadell’installazione des ressortslateraux avant l’installationMontare la porta e regolarelatensione delle einstellen