Andrew ATC200-Lite manual Example of ATC200 System Diagram

Page 13

ATC200-Lite Teletilt® Remote Control Downtilt System

Section 1–Controller Setup

 

 

Antenna

 

 

 

Field Installed

 

 

 

Actuator

 

 

 

ATM200-001

 

 

Cable Assembly

 

Junction Box

ATCB-B01-006

Additional Products:

ATJB200-A01-007

Cable Ground

 

ATS-A01-002 Two-Way Splitter

(Up to 32 antennas

 

 

ATS-B01-003 Three-Way Splitter

602299

 

can be daisy-chained

 

 

 

 

 

by using multiple

Cable Assembly

 

 

junction boxes.)

Lightning Protection Unit

ATCB-B01-060

 

ATLP200-001

 

 

 

 

Cable Assembly

Hanger Kit Accessories

 

ATCB-B01-002

 

 

 

or Cable Ties (40417)

 

Equipment

 

 

 

Cabin

 

Cable Ground

 

 

Local Control Interface

Antenna Control Unit

RS-232 Not Supplied

602299

ATC200-1000-00XX

 

 

 

 

or ATC200-Lite-00XX

 

 

 

Ethernet

Example Cable

dc

 

(10 Base T)

 

 

Lengths Shown

Power

 

 

Figure 1-2. Example of ATC200 System Diagram.

Bulletin 639510

May 2005

1-

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Telecom Parkway Richardson, Texas Tel 214 Fax 214 Andrew Corporation Base Station AntennasPage Revision No Date Description of Changes None May Released Revision HistoryATC200-Lite Teletilt Remote Control Downtilt System Iii ESD Wrist Strap ATC200-Lite Teletilt Remote Control Downtilt System This page intentionally left blank Contents Part Numbering Scheme and Ordering Guide 10-1 ATC200-Lite Series Controller Setup Controller SetupSystem Description ATC200-Lite Series Controller CommunicationATC200-Lite Controller with RS-232 Serial Cable Attached Example of ATC200 System Diagram This page intentionally left blank Program Download and Installation Program InstallationSetup Introduction Screen Completing Setup Screen Software Upgrades and Antenna Definition File UpdatesMay Bulletin Preparing for Program Startup Program Startup and ConfigurationATC200-Lite Application Icon Serial Port Selection at Program StartupSelecting a Serial Port Antenna Definition File Selection Beginning Program OperationSelecting ‘Antenna Files’ from Main Menu This page intentionally left blank Device Search Device Discovery and AddressingClick ‘OK’ Bulletin May Click ‘Remove Device’ AddressingConfirmation of Device Removal 10. Assigning a New Address 13. Closing ‘Manual Addressing’ Screen This page intentionally left blank Selecting Device to be Configured Device ConfigurationMake appropriate selections and text entries Bulletin May If satisfied with new configuration data, click ‘Yes’ Bulletin May This page intentionally left blank Changing the Electrical Downtilt on a Single Antenna Selecting Device for Electrical Downtilt AdjustmentClick ‘Activate’ Enter a new electrical tilt angle Click ‘OK’ May Bulletin Selecting an Antenna Within a Sector Changing the Electrical Downtilt on a Group of AntennasAdding Devices to be Included in the Sector Move Entering New Electrical Tilt Setting for Sector Move Click ‘OK’ Saving/Viewing a Site Report Formatted to Open in Word Saving a Site Report or Site ConfigurationsClick ‘Save’ Assign a filename to the report Select the ‘txtrpt’ file Go to ‘ATC200SiteFiles’ directory Report File Opened in Word Selecting the File Format for Excel Saving/Viewing a Site Report Formatted to Open in ExcelSelect the ‘tabrpt’ file Go to ‘ATC200SiteFiles’ directory Report File Opened in Excel Saving Site Configurations to Hard Drive for Future Use Saving Configurations for Future UseDevice Status and Test Options Device Test, Alarm Status and Device InformationObtaining Device Information Retrieving Current Alarm StatusExecuting a Self Test Movement for a Device Clearing All Alarms on a DeviceSelf Test Results Part Numbering Scheme Part Numbering Scheme and Ordering GuideQuantity Part Number Description Ordering GuideElectrical Control System SpecificationsThis page intentionally left blank Bulletin Bulletin Antennas For ATC200-Lite Series System Appendix BThis page intentionally left blank
Top Page Image Contents