Andrew ATC200-Lite manual Bulletin May

Page 27

ATC200-Lite Teletilt® Remote Control Downtilt System

Section 4–Device Discovery and Addressing

3.At completion of the search, a notification will appear showing the number of devices found (Figure 4-3).

NOTE: If it is known that devices are present and operational, but none were found by the device search, it is possible that the currently selected serial port is not communicating with the controller.

To check serial port communication, repeat the device search and watch the communica- tion light shown on the data LED of the controller. It should blink rapidly during the device search. If it does not, and particularly if the search completes very quickly, the serial port currently selected may not be functional. In this case, use the methods described in Sec- tion 3.2 to select a different serial port and repeat the search until you see activity on the controller data communication LED.

If attempts have been made on all eight serial ports without success, contact your IT department for assistance in determining the reason no serial port is available for use by the program.

4.Click OK on the device search results dialog box (Figure 4-3). Pre-configured and new devices found will display in the ‘Device Information’ list (Figure 4-4).

Note that a new device that has never been configured, will show a ‘Not Configured’ status with no configuration data present.

Figure 4-4. Antenna Information for Devices Found During Search Displayed.

Bulletin 639510

May 2005

4-

Image 27
Contents Telecom Parkway Richardson, Texas Tel 214 Fax 214 Andrew Corporation Base Station AntennasPage Revision No Date Description of Changes None May Released Revision HistoryATC200-Lite Teletilt Remote Control Downtilt System Iii ESD Wrist Strap ATC200-Lite Teletilt Remote Control Downtilt System This page intentionally left blank Contents Part Numbering Scheme and Ordering Guide 10-1 ATC200-Lite Series Controller Communication Controller SetupATC200-Lite Series Controller Setup System DescriptionATC200-Lite Controller with RS-232 Serial Cable Attached Example of ATC200 System Diagram This page intentionally left blank Program Download and Installation Program InstallationSetup Introduction Screen Completing Setup Screen Software Upgrades and Antenna Definition File UpdatesMay Bulletin Preparing for Program Startup Program Startup and ConfigurationATC200-Lite Application Icon Serial Port Selection at Program StartupSelecting a Serial Port Antenna Definition File Selection Beginning Program OperationSelecting ‘Antenna Files’ from Main Menu This page intentionally left blank Device Search Device Discovery and AddressingClick ‘OK’ Bulletin May Click ‘Remove Device’ AddressingConfirmation of Device Removal 10. Assigning a New Address 13. Closing ‘Manual Addressing’ Screen This page intentionally left blank Selecting Device to be Configured Device ConfigurationMake appropriate selections and text entries Bulletin May If satisfied with new configuration data, click ‘Yes’ Bulletin May This page intentionally left blank Changing the Electrical Downtilt on a Single Antenna Selecting Device for Electrical Downtilt AdjustmentClick ‘Activate’ Enter a new electrical tilt angle Click ‘OK’ May Bulletin Selecting an Antenna Within a Sector Changing the Electrical Downtilt on a Group of AntennasAdding Devices to be Included in the Sector Move Entering New Electrical Tilt Setting for Sector Move Click ‘OK’ Saving/Viewing a Site Report Formatted to Open in Word Saving a Site Report or Site ConfigurationsClick ‘Save’ Assign a filename to the report Select the ‘txtrpt’ file Go to ‘ATC200SiteFiles’ directory Report File Opened in Word Selecting the File Format for Excel Saving/Viewing a Site Report Formatted to Open in ExcelSelect the ‘tabrpt’ file Go to ‘ATC200SiteFiles’ directory Report File Opened in Excel Saving Site Configurations to Hard Drive for Future Use Saving Configurations for Future UseDevice Status and Test Options Device Test, Alarm Status and Device InformationObtaining Device Information Retrieving Current Alarm StatusExecuting a Self Test Movement for a Device Clearing All Alarms on a DeviceSelf Test Results Part Numbering Scheme Part Numbering Scheme and Ordering GuideQuantity Part Number Description Ordering GuideElectrical Control System SpecificationsThis page intentionally left blank Bulletin Bulletin Antennas For ATC200-Lite Series System Appendix BThis page intentionally left blank