Gladiator Garageworks GARF19XXVK manual Refrigerator Doors, Reverse Doors optional, Final Steps

Page 4

Refrigerator Doors

TOOLS NEEDED: ⁵⁄₁₆" hex-head socket wrench, #2 Phillips screwdriver, flat-blade screwdriver, ⁵⁄₁₆" open-end wrench, flat 2" putty knife.

IMPORTANT:

■All graphics referenced in the following instructions are included later in this section after “Final Steps.” The graphics shown are for a right-hand swing door (hinges factory installed on the right).

■If you only want to remove and replace the doors, see the “Remove Doors and Hinges” and “Replace Doors and Hinges.”

■Before you begin, turn the control OFF, and remove food and adjustable door or utility bins from doors.

Remove Doors and Hinges

Replace Doors and Hinges

NOTE: Graphic may be reversed if door swing is reversed.

1.Replace the parts for the bottom hinge as shown and tighten screws. See Bottom Hinge graphic. Replace the refrigerator door.

NOTE: Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

2.Assemble the parts for the center hinge as shown and tighten all screws. See Center Hinge graphic. Replace the freezer door.

3.Assemble the parts of the top hinge as shown in the Top Hinge graphic. Do not tighten the screws completely.

4.Line up the doors so that the bottom of the freezer door aligns evenly with the top of the refrigerator door. Tighten all screws.

⁵⁄₁₆" Hex-Head Hinge Screw

1.Unplug refrigerator or disconnect power.

2.Open refrigerator door and remove base grille from the bottom front of the refrigerator. See Base Grille graphic.

3.Close the refrigerator door and keep both doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

4.Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the freezer door free from the cabinet.

5.Remove the parts for the center hinge as shown in the Center Hinge graphic. Lift the refrigerator door free from the cabinet.

6.Remove the parts for the bottom hinge as shown in the Bottom Hinge graphic.

Reverse Doors (optional)

IMPORTANT: If you want to reverse your doors so that they open in the opposite direction, continue with “Reverse Doors (optional)” instructions. If you are not reversing the doors, see “Replace Doors and Hinges.”

Cabinet

1.Remove the ⁵⁄₁₆" hex-head hinge screws from handle side and move them to the opposite side. See Graphic 1.

2.Remove the cabinet hinge hole plugs from the cabinet top and move them to the opposite side hinge holes as shown in Graphic 2.

Doors

1.Remove the door stops from both the freezer and the refrigerator doors and move them to the opposite side. See Graphics 3 and 4.

Final Steps

1.Check all holes to make sure that hole plugs and screws are in place. Reinstall top hinge cover. See Top Hinge graphic.

2.Replace the base grille. See Base Grille graphic.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

3.Plug into a grounded 3 prong outlet.

4.Reset the controls. See “Using the Controls.”

5.Return all removable door parts to doors and food to refrigerator.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Refrigerator Safety User InstructionsInstallation Instructions Clean Before UsingUnpack the Refrigerator Before You Throw Away Your Old Refrigerator or FreezerElectrical Requirements Location RequirementsRecommended Grounding Method Refrigerator Doors Remove Doors and Hinges Replace Doors and HingesReverse Doors optional Final StepsDoor Swing Reversal optional Adjust the Doors Caster InstallationDoor Closing Door AlignmentLower Front Corner Complete the InstallationLower Rear Corner Using the Controls CleaningRefrigerator USE Refrigerator CareTemperature and Moisture TroubleshootingRefrigerator Operation Gladiator Garageworks Major Appliance Warranty Refrigerador Para Garage Chillerator Seguridad DEL RefrigeradorInstrucciones DE Instalación Desempaque el RefrigeradorAntes de tirar su viejo refrigerador o congelador Quitar los materiales de empaqueRequisitos de ubicación Requisitos eléctricosMétodo de conexión a tierra recomendado ImportantePuertas del refrigerador Cómo quitar las puertas y las bisagrasCómo volver a poner las puertas y las bisagras en su lugar Pasos finalesCómo quitar y volver a poner la puerta en su lugar Ajuste las puertas Instalación de las ruedecillasCierre de la puerta Alineamiento de la puertaEsquina inferior trasera Bisagra superior Bisagra centralContratuerca Perno de cabeza Soporte de ruedecilla RuedecillaUso de los controles Cuidado DE SU RefrigeradorLimpieza Cómo cambiar los focos Solución DE ProblemasFuncionamiento del refrigerador Temperatura y humedad La puerta no cierra completamenteEs difícil abrir la puerta La temperatura está demasiado calienteGladiator Garageworks Garantía Limitada DE UN AÑOSécurité DU Réfrigérateur Votre sécurité et celle des autres est très importanteInstructions Dinstallation Déballage du réfrigérateurEnlèvement des matériaux d’emballage Nettoyage avant l’utilisationMéthode recommandée de mise à la terre Exigences demplacementSpécifications électriques Réinstallation Portes et charnières Portes du réfrigérateurDémontage Portes et charnières Inversion des portes facultatifAjustement des portes Fermeture des portesInstallation des roulettes Alignement des portesOutils Nécessaires Pièces FourniesUtilisation des commandes Angle inférieur/avant Achever linstallationUtilisation DU Réfrigérateur Angle inférieur/arrièreRemplacement des ampoules d’éclairage Ajustement des réglages de commandesNettoyage Nettoyage de votre réfrigérateurFonctionnement du réfrigérateur DépannageTempérature et humidité Garantie DES Gros Appareils Ménagers Gladiator Garageworks Garantie Limitée DE UN ANW10131416A EN/FR PN W10131408A

W10131416A, GARF19XXVK specifications

The Gladiator Garageworks GARF19XXVK, W10131416A is a cutting-edge storage solution designed for both functionality and aesthetic appeal in any garage or workspace. This versatile garage storage unit is engineered to withstand the rigors of daily use while maintaining an organized and neat environment.

One of the standout features of the GARF19XXVK is its robust construction. Made from heavy-duty steel, the unit promises durability and resistance to rust and corrosion. With a powder-coated finish, it not only enhances the visual appeal but also adds an extra layer of protection against wear and tear.

The GARF19XXVK is equipped with various shelves and compartments that can be easily adjusted to accommodate items of different sizes. The ability to personalize the shelf heights makes this unit exceptionally practical for storing everything from small tools to larger equipment. This customization feature is essential for maximizing space efficiency, making it ideal for garages of all sizes.

Another notable aspect of the GARF19XXVK is its innovative locking mechanism, which ensures the security of your tools and valuables. This feature is particularly important for homeowners who want to protect their investments from theft or unauthorized access. The unit also includes rubberized feet to prevent slipping, enhancing both stability and safety.

The design of the GARF19XXVK emphasizes both style and functionality, featuring an attractive black finish that can seamlessly integrate into any décor. The sleek look is complemented by its modern profile, making it not just a storage solution but a stylish addition to your garage or workspace.

Technologically, the GARF19XXVK incorporates precision engineering for ease of assembly. It requires minimal tools for setup, allowing users to put together the unit quickly and efficiently. The thoughtful design also includes cutouts to facilitate cable management, promoting a clean and organized environment.

Finally, the GARF19XXVK is compatible with the Gladiator system, allowing for easy integration with other Gladiator products. This compatibility opens up the possibility for extensive customization, letting users create their ideal storage solutions tailored to individual needs.

In summary, the Gladiator Garageworks GARF19XXVK, W10131416A stands out due to its durability, versatile storage options, security features, and stylish design, making it a must-have for anyone looking to optimize their garage space.
Top Page Image Contents