Gladiator Garageworks GARF19XXVK, W10131416A Adjust the Doors, Caster Installation, Door Closing

Page 6

Adjust the Doors

NOTE: If you have the casters installed on your refrigerator, the leveling screws will not work. Shims can be placed under the casters to level a refrigerator that has casters installed.

Door Closing

Your refrigerator has two front adjustable rollers – one on the right and one on the left. If your refrigerator seems unsteady or you want the doors to close easier, adjust the refrigerator's tilt using the instructions below:

1.

Remove the base grille. See Base Grille graphic. The two leveling

 

screws are part of the front roller assemblies which are at the

 

base of the refrigerator on either side.

2.

Use a screwdriver to adjust the leveling screws. Turn the leveling

 

screw to the right to raise that side of the refrigerator or turn the

 

leveling screw to the left to lower that side. It may take several

Caster Installation

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Gather the required tools and parts before starting installation.

TOOLS NEEDED:

¹⁄₂" Socket wrench or nut

³⁄₈" Socket wrench or nut

driver

driver

turns of the leveling screws to adjust the tilt of the refrigerator.

NOTE: Having someone push against the top of the refrigerator

takes some weight off the leveling screws and rollers. This makes

it easier to adjust the screws.

¹⁄₂" Wrench

PARTS SUPPLIED:

Rigid Casters (2)

Swivel Casters (2)

⁵⁄₁₆—18 Self-locking hex-nuts (16)

⁵⁄₁₆—18 x ⁷⁄₈" Hex-head bolts (16)

¼—20 x 1¹⁄₄" Self-tapping hex-head bolts (4)

¼—20 x 1¹⁄₄" lock washers (4)

Caster brackets (located in FeaturePak) (2)

Plastic skids (shipped with the refrigerator)

3.Open both doors again and check to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.

4.Replace the base grille.

Door Alignment

If the space between your doors looks uneven, you can adjust it using the instructions below:

1.Pry off the top hinge cover.

2.Loosen the top hinge screws using a ⁵⁄₁₆" socket or wrench.

3.Have someone hold the door in place or put a spacer between the doors while you tighten the top hinge screws.

4.Replace the top hinge cover.

1.Before you begin, turn the refrigerator control OFF.

2.Unplug refrigerator or disconnect power.

3.Remove food and any adjustable shelves and bins from refrigerator.

4.Open the lower compartment door and remove the base grille. Remove the grille by grasping the grille with both hands, lifting up and pulling bottom of the grille toward you.

5.Place the plastic skids (shipped with the refrigerator) on the floor at least 3 ft (91.44 cm) apart. Lay a piece of cardboard or other protective material over the skids. This will elevate the refrigerator to allow for easier caster installation and also protect it from scratches.

NOTE: If the skids have been discarded or are not available, 2" x 4" boards may be used.

6.Place the refrigerator on its side on top of the cardboard or protective material. Make sure the door hinge is facing upward.

IMPORTANT: It is important that the door hinge face upward during the entire caster installation.

A

B

A. Top hinge

B. Center hinge

6

Image 6
Contents Refrigerator Safety User InstructionsUnpack the Refrigerator Installation InstructionsClean Before Using Before You Throw Away Your Old Refrigerator or FreezerLocation Requirements Electrical RequirementsRecommended Grounding Method Reverse Doors optional Refrigerator DoorsRemove Doors and Hinges Replace Doors and Hinges Final StepsDoor Swing Reversal optional Door Closing Adjust the DoorsCaster Installation Door AlignmentComplete the Installation Lower Front CornerLower Rear Corner Refrigerator USE Using the ControlsCleaning Refrigerator CareTroubleshooting Temperature and MoistureRefrigerator Operation Gladiator Garageworks Major Appliance Warranty Refrigerador Para Garage Chillerator Seguridad DEL RefrigeradorAntes de tirar su viejo refrigerador o congelador Instrucciones DE InstalaciónDesempaque el Refrigerador Quitar los materiales de empaqueMétodo de conexión a tierra recomendado Requisitos de ubicaciónRequisitos eléctricos ImportanteCómo volver a poner las puertas y las bisagras en su lugar Puertas del refrigeradorCómo quitar las puertas y las bisagras Pasos finalesCómo quitar y volver a poner la puerta en su lugar Cierre de la puerta Ajuste las puertasInstalación de las ruedecillas Alineamiento de la puertaContratuerca Perno de cabeza Soporte de ruedecilla Esquina inferior traseraBisagra superior Bisagra central RuedecillaCuidado DE SU Refrigerador Uso de los controlesLimpieza Solución DE Problemas Cómo cambiar los focosFuncionamiento del refrigerador Es difícil abrir la puerta Temperatura y humedadLa puerta no cierra completamente La temperatura está demasiado calienteGladiator Garageworks Garantía Limitada DE UN AÑOSécurité DU Réfrigérateur Votre sécurité et celle des autres est très importanteEnlèvement des matériaux d’emballage Instructions DinstallationDéballage du réfrigérateur Nettoyage avant l’utilisationExigences demplacement Méthode recommandée de mise à la terreSpécifications électriques Démontage Portes et charnières Réinstallation Portes et charnièresPortes du réfrigérateur Inversion des portes facultatifAjustement des portes Fermeture des portesOutils Nécessaires Installation des roulettesAlignement des portes Pièces FourniesUtilisation DU Réfrigérateur Utilisation des commandesAngle inférieur/avant Achever linstallation Angle inférieur/arrièreNettoyage Remplacement des ampoules d’éclairageAjustement des réglages de commandes Nettoyage de votre réfrigérateurDépannage Fonctionnement du réfrigérateurTempérature et humidité Garantie DES Gros Appareils Ménagers Gladiator Garageworks Garantie Limitée DE UN ANW10131416A EN/FR PN W10131408A

W10131416A, GARF19XXVK specifications

The Gladiator Garageworks GARF19XXVK, W10131416A is a cutting-edge storage solution designed for both functionality and aesthetic appeal in any garage or workspace. This versatile garage storage unit is engineered to withstand the rigors of daily use while maintaining an organized and neat environment.

One of the standout features of the GARF19XXVK is its robust construction. Made from heavy-duty steel, the unit promises durability and resistance to rust and corrosion. With a powder-coated finish, it not only enhances the visual appeal but also adds an extra layer of protection against wear and tear.

The GARF19XXVK is equipped with various shelves and compartments that can be easily adjusted to accommodate items of different sizes. The ability to personalize the shelf heights makes this unit exceptionally practical for storing everything from small tools to larger equipment. This customization feature is essential for maximizing space efficiency, making it ideal for garages of all sizes.

Another notable aspect of the GARF19XXVK is its innovative locking mechanism, which ensures the security of your tools and valuables. This feature is particularly important for homeowners who want to protect their investments from theft or unauthorized access. The unit also includes rubberized feet to prevent slipping, enhancing both stability and safety.

The design of the GARF19XXVK emphasizes both style and functionality, featuring an attractive black finish that can seamlessly integrate into any décor. The sleek look is complemented by its modern profile, making it not just a storage solution but a stylish addition to your garage or workspace.

Technologically, the GARF19XXVK incorporates precision engineering for ease of assembly. It requires minimal tools for setup, allowing users to put together the unit quickly and efficiently. The thoughtful design also includes cutouts to facilitate cable management, promoting a clean and organized environment.

Finally, the GARF19XXVK is compatible with the Gladiator system, allowing for easy integration with other Gladiator products. This compatibility opens up the possibility for extensive customization, letting users create their ideal storage solutions tailored to individual needs.

In summary, the Gladiator Garageworks GARF19XXVK, W10131416A stands out due to its durability, versatile storage options, security features, and stylish design, making it a must-have for anyone looking to optimize their garage space.