Whirlpool W10531342A Installation Instructions, Unpack Range, Install Anti-Tip Bracket

Page 7

Burner Input Requirements

Input ratings shown on the model/serial rating plate are for elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a rate of 4% for each 1,000 ft (304.8 m) above sea level.

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least 1" water column pressure above the manifold pressure shown on the model/serial rating plate.

Line pressure testing above ½ psi gauge (14" WCP)

The range and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ psi (3.5 kPa).

Line pressure testing at ½ psi gauge (14" WCP) or lower

The range must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psi (3.5 kPa).

INSTALLATION INSTRUCTIONS

Unpack Range

WARNING

Excessive Weight Hazard

Use two or more people to move and install range. Failure to do so can result in back or other injury.

1.Do not use oven door handle to lift or move the range

2.Remove shipping materials, tape and film from range. Keep cardboard bottom under range.

3.Remove oven racks and parts package from inside oven.

4.To place range on its back, take 4 cardboard corners from the carton. Stack one cardboard corner on top of another. Repeat with the other 2 corners. Place them lengthwise on the floor behind the range to support the range when it is laid on its back.

5.Using 2 or more people, firmly grasp the range and gently lay it on its back on the cardboard corners.

6.Pull cardboard bottom firmly to remove.

7.Use an adjustable wrench to loosen the leveling legs. Adjust the leveling legs to the correct height. Leveling legs can be loosened to add up to a maximum of 1" (2.5 cm). A minimum of ³⁄₁₆" (0.5 cm) is needed to engage the anti-tip bracket.

NOTE: If height adjustment is made when range is standing, tilt the range back to adjust the front legs, then tilt forward to adjust the rear legs.

8.Place cardboard or hardboard in front of range. Using 2 or more people, stand range back up onto cardboard or hardboard.

Install Anti-Tip Bracket

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

1.Remove the anti-tip bracket from where it is attached inside the oven with a wire tie.

2.Determine which mounting method to use: floor or wall.

If you have a stone or masonry floor, you can use the wall mounting method. If you are installing the range in a mobile home, you must secure the range to the floor.

7

Image 7
Contents Installation Instructions 20 50.8 CM Freestanding GAS Range Your safety and the safety of others are very important Range SafetyAnti-Tip Bracket Range Foot Tools and Parts Installation RequirementsLocation Requirements Mobile home installations require Mobile Home Additional Installation RequirementsProduct Dimensions Freestanding Range Cabinet DimensionsGas Pressure Regulator Gas Supply RequirementsType of Gas Gas Supply LineUnpack Range Installation InstructionsInstall Anti-Tip Bracket Gas Supply Pressure TestingFloor Mounting Make Gas ConnectionTypical rigid pipe connection Typical flexible connectionComplete Connection Verify Anti-Tip Bracket Is Installed EngagedLevel Range Installing/Replacing the BatteryWhile a knob is Then Lite position, if Battery Status IndicatorInitial lighting and gas flame adjustments Electronic Ignition SystemCheck Operation of Oven/Broil Burner If the low flame needs adjustingIf the flame needs adjusting Check Operation of Cooktop BurnersIf you need Assistance or Service Complete InstallationIf range does not operate, check the following LP Gas Conversion GAS ConversionsTo Convert Gas Pressure Regulator To Convert Surface Burners Natural Gas Conversion Complete ConversionTo Convert Oven Burner Turn the cap over so that N or NAT is visible Natural gas oven orifice spud stamped with Page W10531342A