AMX DAS-T0804-SIG Tango Audio Controllers Product Specifications, Front Panel Components

Page 14

Tango Series Audio Controllers

Product Specifications

The following table provides technical specifications for the Tango Audio Controllers. Unless otherwise noted, these specifications apply to both the DAS-T0804-SIG and DAS-T0808-SIG models.

Tango Audio Controllers Product Specifications

Models Available:

• DAS-T0804-SIGTango 8-Source, 4-Zone Audio Controller (FG1103-01)

 

• DAS-T0808-SIGTango 8-Source, 8-Zone Audio Controller (FG1103-02)

 

 

Stereo Output:

25 Watts/CH stereo (20Hz to 20Khz @ .1% THD)

 

 

Power:

960W max (Actual average usage = 300W)

 

 

Zone Support:

DAS-T0804-SIG - Four independent audio Zones.

 

DAS-T0808-SIG - Eight independent audio Zones.

 

• Each Zone is protected thermally.

 

• Zone grouping.

 

• Independent Volume, Bass, Treble, Balance and SRS® controls in each

 

zone.

 

 

Stereo Amplifiers:

• 40 Watts/CH stereo amplifiers (20Hz to 20Khz @ .1% THD).

 

• Amplifiers are protected from overload and thermal runaway.

 

 

SRS/WOW®:

Standard SRS/WOW® audio enhancement technology by SRS Labs, on all

 

zones.

 

Note: SRS/WOW is a registered trademark of SRS labs, Inc.

 

 

Front Panel Components:

 

 

 

• Light Bar

Blue light bar indicates power status.

 

 

• LEDs

Blue LEDs indicate level status.

 

 

• Function/Navigation Buttons

5 pushbuttons allow for front panel programming, selection of sources, tun-

 

ing AM/FM radio stations, or Sirius satellite radio stations (when equipped

 

with the optional Sirius and/or AM/FM Tuner Card).

 

 

• IR Receiver

This is where you must aim the remotes from your audio source components

 

so the Controller can learn and emulate those commands.

 

 

• LCD Display

Displays information necessary during the programming steps and afterward

 

is the display to indicate information about the source input and zone activity.

 

 

Rear Panel Components:

 

 

 

• Power Switch & Receptacle

The master power switch will remain in the ON position normally.

 

 

• Paging In/Out Ports

RCA jacks to connect to Paging devices (any audio input can be used as a

 

paging device). The Paging device connects to the Controller via the "Paging

 

In" connector. The “Paging Out” connector is used to carry the page to Zone

 

Expander(s).

 

 

• RJ 45 Port

Ethernet Port for future expansion

 

 

• RS-232 Port

DB9 connector allows the Tango Audio Controller to receive Controller Com-

 

mand Messages and provide status messages. This port is intended

 

primarily for troubleshooting purposes.

 

 

• AM/FM Antenna Inputs

Connections for the AM and FM Antennas.

 

 

• Audio Inputs

Stereo Inputs, 47K impedance, buffered.

 

 

• Audio Outputs

Stereo Looping Outputs, buffered.

 

 

• IR Outputs

• DAS-T0804-SIG: Four IR 3.5mm mono output jacks.

 

• DAS-T0808-SIG: Eight IR 3.5mm mono output jacks.

 

 

• Zone Outputs

• DAS-T0804-SIG: 4 zone output connectors (connect to Metreau keypads)

 

• DAS-T0808-SIG: 8 zone output connectors (connect to Metreau keypads)

 

 

• Expansion Port

RJ-11 Port connects main Tango Controller with Tango Zone Expanders.

 

 

Dimensions (HWD):

• 4" x 17" x 13.5"

(including feet)

• 10.16 cm x 43.18 cm x 34.29 cm

 

 

Weight:

Max. weight with 8 zones - 31 lbs (14.06 kg)

 

 

2

Tango Series Audio Controllers

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Tango AMX Limited Warranty and Disclaimer Important Safety Instructions Important Safety Instructions Table of Contents System Integration Drawings Tuner Modules IR Commands By Source Type Mdrg Troubleshooting No Keypad Activity At All Table of Contents Viii Tango Series Audio Controllers Tango Series Audio Controllers OverviewFront Panel Components Product SpecificationsTango Audio Controllers Product Specifications Rear Panel ComponentsDAS-TRMK Rack Mount Kit for Tango Audio Controllers and Zone Tango Series Audio Controllers Ventilation InstallationRack-Mounting Connector Layout Rear Panel Speaker Wire Technology SWTCabling Installation Instructions Cable TypeConnecting Zone Outputs Connecting Sources Audio Inputs/OutputsConnecting IR Outputs Connecting SWT Speakers to SWT Keypads SWT ConnectorsConnecting SWT Keypads to the Tango Controller Connecting Paging Inputs/Outputs Connecting Tango Zone ExpandersFrom Audio Device L/R To Zones DAS-T0804-SIG 4-Zone Controller Zone Expander AddressingDAS-T0808-SIG 8-Zone Controller On-Board AM/FM Tuner Module Connecting the RS-232 Serial PortAntenna Installation RS-232 CableConnecting a Tango Amplifier Wiring DiagramMIO R-1 Audio Specifications MIO-R1 Audio Tango Distributed Audio Remote ControlSpecifications Installing Custom Buttons Inserting Batteries into The MIO R-1 Audio Programming The MIO R-1 Audio Using KeypadBuilderBattery Low Indicator Zone Control Tone Control & SRS SettingSRS Bass Boost, Focus, 3D and WOW Settings CD and DVD Source ControlInternal Tuner and Audio Server Satellite and OtherDirect Numeric Access Configuration ModeLED Awake Brightness Battery TypeLED Sleep Mode Brightness Additional DocumentationSystem Integration Drawings Using Four Conductor Speaker WireUsing the Audio Zone Expander SWT Distributed Audio SystemsAuxiliary Amplifier Configuration SWT Special Wiring ConfigurationsDistribution Wiring RF InterferenceRemote Amplifier Configuration Wire Configurations Keypad for Control OnlySplit Zone / Analog Volume Control Option 1 One Keypad Split Zone / Analog Volume control Option 2 one KeypadKey-By-Key Programming Setup and ConfigurationSource Documentation Programming WorksheetsProgramming Panel Programming the Tango ControllerMain Menu screen System Setup Mode screen System Setup MRC Setup Mode screenMRC Setup Mode Options screen Programming Source EquipmentLearn IR Commands IR OK 50 percent sure 1 command receivedSetting Gain/Attenuation Adjusting Input AttenuationAdjusting Output Gain Input Attenuation Mode screenPaging Setting Paging VolumeRoom Control Settings Selecting AM/FM System Setup Tuner Setup Mode screenSetting Presets Selecting Stereo/MonoSetting System Date System Setup Clock Setup Mode screenSetting System Time Setting the Day of the weekBacklight Options Backlight IntensityDevice Status Backlight ModeAbout Options screen System Setup Mode About Program LCD KPSetup and Configuration Tango Series Audio Controllers DAS-SIRIUS Tuner Tuner ModulesDAS-AMFM Tuner Top = Slot Bottom = Slot Front Audio Controller Jumpers Location Setting the JumpersAudio Controller Jumpers ON/OFF Settings Audio Controller Jumpers Dual Tuner Setting DAS-AMFM Tuner Module JumpersRemoving the Pre-Installed DAS-AMFM Tuner Module Installing a Second DAS-AMFM Tuner Module Rear Panel Tuner Slots 1Ribbon Cable Tuner Installing the DAS-SIRIUS Tuner Module Cable RoutingConnecting and Positioning the Sirius Antenna ModuleActivating Your Sirius Subscription Channels AMX Duet Module Interface SpecificationsPort Mapping Mi-Series & Tango Controllers Port MappingTango Controllers Channels Levels Command ControlMi-Series & Tango Controllers Command Control Mi-Series & Tango Controllers LevelsInput ?FWVERSION?INPUT PassbackReinit Tunerpresetsave?PROPERTY ?VERSIONBand Command FeedbackMi-Series & Tango Controllers Command Feedback FwversionTunemode ProductidProperty VersionOther External Source Commands Referenced by Source TypeInput Source Types CD CD IR Commands By Source TypeLearn IR by Source Type DVD DVD SAT SatelliteOther Other AudioAudio Server Matrix Onboard = Seek DownSerial Port Communication Serial Control StringsGeneral Information Network CommunicationMver Command MessagesCommand Messages MgcfBdhi AMXMgbd BdloMSTRr,t MSBSr,bMGBSr MGTRrMGSCr MSAOsMSSCr,s MSSRr,sMGGLs MGSRrMSGLs,i,o MSPVr,v MSPGr,sMGPGr MGPVrMGSTr MSSTs,x MCMDs,x, yMSPRr,x MSBLr,xMGBLr MGPRrB2,b1 MSRGs,b8,b7B6,b5,b4,b3 MARGg,rMDRGz MRRGrMdrg MGRGrMGRSs MDGVr,iMSGVr,v MSFVr,s,fMCLOr MGFVr,sMSLOr MgloMSTPs MGPSs,nMRPSs,n Satellite Receiver ‘ssss’ where ‘ssss’ is the station number MSSDs,dCgst MGSSsCSSTh,m,s CCALrSgid Status Codes for Sirius Tuner Mcmd Command CodesMcmd Command Codes Status Codes for Sirius TunerStatus Messages Status MessagesMASOFF0 MGSTr,v,bb,t,s,r,z,l,p MBALr,xMPRVr,x MRGSz,s,b8,b7,b6MPRSs,n,p MFAVr,s,fMLOTb8,b7,b6 MSTPs,tRSSTx,y,z CSTv,h,m,sCALMr,s,v,h,m RSIDx,ySymptom Possible Causes Section TroubleshootingPower Connections Source Unit ConnectionsLED Does Not light Zone Connection ProblemsDead Zones Source ConnectionsNo Keypad Activity At All Keypad Lights, No SoundProgramming Troubleshooting Tango Series Audio Controllers It’s Your World Take Control

DAS-T0808-SIG, DAS-T0804-SIG specifications

The AMX DAS-T0804-SIG and DAS-T0808-SIG are the forefront of advanced data distribution systems, designed to cater to the dynamic needs of commercial audio-visual installations. These models provide exceptional performance in managing and distributing various signals efficiently, ensuring seamless integration with a wide array of multimedia components.

One of the standout features of the DAS-T0804-SIG is its ability to support up to four output signals, while the DAS-T0808-SIG extends this capability to eight outputs. This scalability makes both units ideal for projects requiring flexible signal routing, whether for corporate environments, educational institutions, or entertainment venues.

Both models leverage cutting-edge digital signal processing (DSP) technologies to enhance audio quality and ensure fidelity during signal transmission. The units are equipped with advanced signal management features, including automatic gain control and equalization, which help maintain consistent audio levels and optimize playback across different environments. This ensures that users experience high-quality sound without the hassle of manual adjustments.

Connectivity options are plentiful, with support for both HDMI and analog inputs. The HDMI ports allow for seamless integration with high-definition video sources, while the analog inputs cater to older equipment, making the DAS-T0804-SIG and DAS-T0808-SIG versatile choices for mixed-system setups. The ability to handle diverse input types helps manage the challenges of modern AV environments, where devices can vary widely.

Another notable characteristic is the intuitive user interface that facilitates easy configuration and operation. The models come equipped with LED indicators for monitoring signal status, which provide real-time feedback and help troubleshoot issues swiftly. This user-centric design is particularly beneficial for installation professionals who require efficient workflows.

The DAS-T0804-SIG and DAS-T0808-SIG are also built with robust security features to protect against unauthorized access and ensure integrity in signal transmission. This is increasingly crucial in settings where sensitive information may be communicated.

In summary, the AMX DAS-T0804-SIG and DAS-T0808-SIG systems are powerful, flexible, and secure solutions for modern AV installations, characterized by their advanced signal processing, versatile connectivity, and intuitive design. Their ability to accommodate a variety of applications makes them an essential tool for any professional seeking to optimize audio-visual performance.
Top Page Image Contents