AMX DAS-T0808-SIG, DAS-T0804-SIG manual Connecting and Positioning the Sirius Antenna, Module

Page 59

rear of Controller (side view)

Slot 1 connector (connect to DAS-SIRIUS

Module)

DAS-AMFM

Slot 2 connector

(shown connected to DAS-AMFM Module)

FIG. 74 Tuner 1 / 2 Module Connections (side view of Controller)

Tuner Modules

Tuner Ribbon

Cable

Verify that all of the 20-pin connectors of the Tuner Ribbon Cable are securely plugged into their respective boards.

While it is recommended that you use the Slot 2 connector on the ribbon cable to connect the Tuner installed in Slot 2 (in this case, the DAS-AMFM Tuner), the ribbon cable itself does not determine which Tuner is Tuner 1 and Tuner 2. This determination is set by the jumper settings on each Tuner Module (see “Tuner 1 Jumper Settings” and “Tuner 2 Jumper Settings” above. Therefore, it is not required that the connections indicated in FIG. 10 are followed exactly, as long as the Tuner Jumper Settings are set correctly for each installed Tuner Module.

The Controller should only be powered back on once all Tuners are installed and the cover is replaced on the chassis.

Connecting and Positioning the SIRIUS Antenna

1.Connect the provided SIRIUS Antenna to the DAS-SIRIUS (see FIG. 56 on page 39).

2.Verify the Signal strength

a.Access the programming menus via the front of the Controller.

b.Select Setup\SIRIUS.

c.Select "Status".

d.Select "SAT" to determine the Satellite Signal Strength. Ensure the signal strength is at a minimum of "weak". Adjustments may need to be made to the position of the Antenna in order to get a better signal.

Tango / Mi-Series Audio Controllers

47

 

 

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Tango AMX Limited Warranty and Disclaimer Important Safety Instructions Important Safety Instructions Table of Contents System Integration Drawings Tuner Modules IR Commands By Source Type Mdrg Troubleshooting No Keypad Activity At All Table of Contents Viii Tango Series Audio Controllers Overview Tango Series Audio ControllersRear Panel Components Product SpecificationsTango Audio Controllers Product Specifications Front Panel ComponentsDAS-TRMK Rack Mount Kit for Tango Audio Controllers and Zone Tango Series Audio Controllers Ventilation InstallationRack-Mounting Cable Type Speaker Wire Technology SWTCabling Installation Instructions Connector Layout Rear PanelConnecting Zone Outputs Connecting Sources Audio Inputs/OutputsConnecting IR Outputs Connecting SWT Speakers to SWT Keypads SWT ConnectorsConnecting SWT Keypads to the Tango Controller Connecting Tango Zone Expanders Connecting Paging Inputs/OutputsFrom Audio Device L/R To Zones DAS-T0804-SIG 4-Zone Controller Zone Expander AddressingDAS-T0808-SIG 8-Zone Controller RS-232 Cable Connecting the RS-232 Serial PortAntenna Installation On-Board AM/FM Tuner ModuleWiring Diagram Connecting a Tango AmplifierMIO R-1 Audio Specifications MIO-R1 Audio Tango Distributed Audio Remote ControlSpecifications Installing Custom Buttons Inserting Batteries into The MIO R-1 Audio Programming The MIO R-1 Audio Using KeypadBuilderBattery Low Indicator Zone Control Tone Control & SRS SettingSRS Bass Boost, Focus, 3D and WOW Settings Satellite and Other Source ControlInternal Tuner and Audio Server CD and DVDConfiguration Mode Direct Numeric AccessAdditional Documentation Battery TypeLED Sleep Mode Brightness LED Awake BrightnessSWT Distributed Audio Systems Using Four Conductor Speaker WireUsing the Audio Zone Expander System Integration DrawingsRF Interference SWT Special Wiring ConfigurationsDistribution Wiring Auxiliary Amplifier ConfigurationWire Configurations Keypad for Control Only Remote Amplifier ConfigurationSplit Zone / Analog Volume control Option 2 one Keypad Split Zone / Analog Volume Control Option 1 One KeypadProgramming Worksheets Setup and ConfigurationSource Documentation Key-By-Key ProgrammingProgramming Panel Programming the Tango ControllerMain Menu screen System Setup MRC Setup Mode screen System Setup Mode screenProgramming Source Equipment MRC Setup Mode Options screenIR OK 50 percent sure 1 command received Learn IR CommandsAdjusting Input Attenuation Setting Gain/AttenuationInput Attenuation Mode screen Adjusting Output GainPaging Setting Paging VolumeRoom Control Settings Selecting Stereo/Mono System Setup Tuner Setup Mode screenSetting Presets Selecting AM/FMSetting the Day of the week System Setup Clock Setup Mode screenSetting System Time Setting System DateBacklight Intensity Backlight OptionsDevice Status Backlight ModeAbout Options screen Program LCD KP System Setup Mode AboutSetup and Configuration Tango Series Audio Controllers DAS-SIRIUS Tuner Tuner ModulesDAS-AMFM Tuner Top = Slot Bottom = Slot Front Audio Controller Jumpers Location Setting the JumpersAudio Controller Jumpers ON/OFF Settings DAS-AMFM Tuner Module Jumpers Audio Controller Jumpers Dual Tuner SettingRemoving the Pre-Installed DAS-AMFM Tuner Module Rear Panel Tuner Slots 1 Installing a Second DAS-AMFM Tuner ModuleRibbon Cable Tuner Cable Routing Installing the DAS-SIRIUS Tuner ModuleModule Connecting and Positioning the Sirius AntennaActivating Your Sirius Subscription Mi-Series & Tango Controllers Port Mapping AMX Duet Module Interface SpecificationsPort Mapping ChannelsTango Controllers Channels Mi-Series & Tango Controllers Levels Command ControlMi-Series & Tango Controllers Command Control LevelsPassback ?FWVERSION?INPUT Input?VERSION Tunerpresetsave?PROPERTY ReinitFwversion Command FeedbackMi-Series & Tango Controllers Command Feedback BandVersion ProductidProperty TunemodeOther External Source Commands Referenced by Source TypeInput Source Types CD CD IR Commands By Source TypeLearn IR by Source Type SAT Satellite DVD DVDOther Other AudioAudio Server = Seek Down Matrix OnboardNetwork Communication Serial Control StringsGeneral Information Serial Port CommunicationMgcf Command MessagesCommand Messages MverBdlo AMXMgbd BdhiMGTRr MSBSr,bMGBSr MSTRr,tMSSRr,s MSAOsMSSCr,s MGSCrMGGLs MGSRrMSGLs,i,o MGPVr MSPGr,sMGPGr MSPVr,vMGSTr MCMDs,x, y MSSTs,xMGPRr MSBLr,xMGBLr MSPRr,xMARGg,r MSRGs,b8,b7B6,b5,b4,b3 B2,b1MGRGr MRRGrMdrg MDRGzMSFVr,s,f MDGVr,iMSGVr,v MGRSsMglo MGFVr,sMSLOr MCLOrMSTPs MGPSs,nMRPSs,n MSSDs,d Satellite Receiver ‘ssss’ where ‘ssss’ is the station numberCCALr MGSSsCSSTh,m,s CgstSgid Status Codes for Sirius Tuner Mcmd Command CodesMcmd Command Codes Status Codes for Sirius TunerStatus Messages Status MessagesMASOFF0 MRGSz,s,b8,b7,b6 MBALr,xMPRVr,x MGSTr,v,bb,t,s,r,z,l,pMSTPs,t MFAVr,s,fMLOTb8,b7,b6 MPRSs,n,pRSIDx,y CSTv,h,m,sCALMr,s,v,h,m RSSTx,y,zSource Unit Connections TroubleshootingPower Connections Symptom Possible Causes SectionSource Connections Zone Connection ProblemsDead Zones LED Does Not lightKeypad Lights, No Sound No Keypad Activity At AllProgramming Troubleshooting Tango Series Audio Controllers It’s Your World Take Control

DAS-T0808-SIG, DAS-T0804-SIG specifications

The AMX DAS-T0804-SIG and DAS-T0808-SIG are the forefront of advanced data distribution systems, designed to cater to the dynamic needs of commercial audio-visual installations. These models provide exceptional performance in managing and distributing various signals efficiently, ensuring seamless integration with a wide array of multimedia components.

One of the standout features of the DAS-T0804-SIG is its ability to support up to four output signals, while the DAS-T0808-SIG extends this capability to eight outputs. This scalability makes both units ideal for projects requiring flexible signal routing, whether for corporate environments, educational institutions, or entertainment venues.

Both models leverage cutting-edge digital signal processing (DSP) technologies to enhance audio quality and ensure fidelity during signal transmission. The units are equipped with advanced signal management features, including automatic gain control and equalization, which help maintain consistent audio levels and optimize playback across different environments. This ensures that users experience high-quality sound without the hassle of manual adjustments.

Connectivity options are plentiful, with support for both HDMI and analog inputs. The HDMI ports allow for seamless integration with high-definition video sources, while the analog inputs cater to older equipment, making the DAS-T0804-SIG and DAS-T0808-SIG versatile choices for mixed-system setups. The ability to handle diverse input types helps manage the challenges of modern AV environments, where devices can vary widely.

Another notable characteristic is the intuitive user interface that facilitates easy configuration and operation. The models come equipped with LED indicators for monitoring signal status, which provide real-time feedback and help troubleshoot issues swiftly. This user-centric design is particularly beneficial for installation professionals who require efficient workflows.

The DAS-T0804-SIG and DAS-T0808-SIG are also built with robust security features to protect against unauthorized access and ensure integrity in signal transmission. This is increasingly crucial in settings where sensitive information may be communicated.

In summary, the AMX DAS-T0804-SIG and DAS-T0808-SIG systems are powerful, flexible, and secure solutions for modern AV installations, characterized by their advanced signal processing, versatile connectivity, and intuitive design. Their ability to accommodate a variety of applications makes them an essential tool for any professional seeking to optimize audio-visual performance.
Top Page Image Contents