AMX DAS-T0804-SIG manual Installing a Second DAS-AMFM Tuner Module, Rear Panel Tuner Slots 1

Page 56

Tuner Modules

Installing a Second DAS-AMFM Tuner Module

The following steps describe installing a second DAS-AMFM tuner module into Slot 1 (in addition to the DAS-AMFM module that comes pre-installed in Slot 2). In these instructions, the second tuner is referred to as “Tuner 2”.

1.Remove the cover from the controller.

2.With the back of the unit facing you, remove the screws from the Tuner Option cover plate at the right top corner of the rear panel (FIG. 65) and remove the plate. Retain the screws, as they will be used to install the tuner module.

Slot 1

(Tuner Option cover plate installed)

Slot 2

(DAS-AMFM module pre-installed)

FIG. 65 Rear Panel - Tuner Slots 1 and 2

3.Carefully insert the second DAS-AMFM tuner module into Slot 1, with the electronics facing up, and use the screws that attached the Tuner Option cover plate to secure the tuner to the controller.

Be careful not to damage the ribbon cable on the top of the Tuner module.

4.Place the Rear Panel connector at the end of the ribbon cable (FIG. 66) on the rear board pin-bus, keeping the red stripe at the top.

RED STRIPE (to Pin 1)

not used

 

 

Slot 2

 

Slot 1 (see Note below)

 

Rear Panel

 

 

FIG. 66 Tuner Ribbon Cable

5.Connect the "Slot 1" connector on the ribbon cable to the Tuner 2 module (FIG. 67).

The ribbon cable must be oriented so that the red stripe is connected to Pin 1 on the connector.

Rear of controller

20-pin connector on Tuner 2

FIG. 67 Tuner 2 Module Connection

Verify that both ends of the cable are securely plugged into their respective boards through the 20-pin connectors (FIG. 68).

44

Tango / Mi-Series Audio Controllers

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Tango AMX Limited Warranty and Disclaimer Important Safety Instructions Important Safety Instructions Table of Contents System Integration Drawings Tuner Modules IR Commands By Source Type Mdrg Troubleshooting No Keypad Activity At All Table of Contents Viii Tango Series Audio Controllers Tango Series Audio Controllers OverviewProduct Specifications Tango Audio Controllers Product SpecificationsFront Panel Components Rear Panel ComponentsDAS-TRMK Rack Mount Kit for Tango Audio Controllers and Zone Tango Series Audio Controllers Ventilation InstallationRack-Mounting Speaker Wire Technology SWT Cabling Installation InstructionsConnector Layout Rear Panel Cable TypeConnecting Zone Outputs Connecting Sources Audio Inputs/OutputsConnecting IR Outputs Connecting SWT Speakers to SWT Keypads SWT ConnectorsConnecting SWT Keypads to the Tango Controller Connecting Paging Inputs/Outputs Connecting Tango Zone ExpandersFrom Audio Device L/R To Zones DAS-T0804-SIG 4-Zone Controller Zone Expander AddressingDAS-T0808-SIG 8-Zone Controller Connecting the RS-232 Serial Port Antenna InstallationOn-Board AM/FM Tuner Module RS-232 CableConnecting a Tango Amplifier Wiring DiagramMIO R-1 Audio Specifications MIO-R1 Audio Tango Distributed Audio Remote ControlSpecifications Installing Custom Buttons Inserting Batteries into The MIO R-1 Audio Programming The MIO R-1 Audio Using KeypadBuilderBattery Low Indicator Zone Control Tone Control & SRS SettingSRS Bass Boost, Focus, 3D and WOW Settings Source Control Internal Tuner and Audio ServerCD and DVD Satellite and OtherDirect Numeric Access Configuration ModeBattery Type LED Sleep Mode BrightnessLED Awake Brightness Additional DocumentationUsing Four Conductor Speaker Wire Using the Audio Zone ExpanderSystem Integration Drawings SWT Distributed Audio SystemsSWT Special Wiring Configurations Distribution WiringAuxiliary Amplifier Configuration RF InterferenceRemote Amplifier Configuration Wire Configurations Keypad for Control OnlySplit Zone / Analog Volume Control Option 1 One Keypad Split Zone / Analog Volume control Option 2 one KeypadSetup and Configuration Source DocumentationKey-By-Key Programming Programming WorksheetsProgramming Panel Programming the Tango ControllerMain Menu screen System Setup Mode screen System Setup MRC Setup Mode screenMRC Setup Mode Options screen Programming Source EquipmentLearn IR Commands IR OK 50 percent sure 1 command receivedSetting Gain/Attenuation Adjusting Input AttenuationAdjusting Output Gain Input Attenuation Mode screenPaging Setting Paging VolumeRoom Control Settings System Setup Tuner Setup Mode screen Setting PresetsSelecting AM/FM Selecting Stereo/MonoSystem Setup Clock Setup Mode screen Setting System TimeSetting System Date Setting the Day of the weekBacklight Options Backlight IntensityDevice Status Backlight ModeAbout Options screen System Setup Mode About Program LCD KPSetup and Configuration Tango Series Audio Controllers DAS-SIRIUS Tuner Tuner ModulesDAS-AMFM Tuner Top = Slot Bottom = Slot Front Audio Controller Jumpers Location Setting the JumpersAudio Controller Jumpers ON/OFF Settings Audio Controller Jumpers Dual Tuner Setting DAS-AMFM Tuner Module JumpersRemoving the Pre-Installed DAS-AMFM Tuner Module Installing a Second DAS-AMFM Tuner Module Rear Panel Tuner Slots 1Ribbon Cable Tuner Installing the DAS-SIRIUS Tuner Module Cable RoutingConnecting and Positioning the Sirius Antenna ModuleActivating Your Sirius Subscription AMX Duet Module Interface Specifications Port MappingChannels Mi-Series & Tango Controllers Port MappingTango Controllers Channels Command Control Mi-Series & Tango Controllers Command ControlLevels Mi-Series & Tango Controllers Levels?FWVERSION ?INPUTInput PassbackTunerpresetsave ?PROPERTYReinit ?VERSIONCommand Feedback Mi-Series & Tango Controllers Command FeedbackBand FwversionProductid PropertyTunemode VersionOther External Source Commands Referenced by Source TypeInput Source Types CD CD IR Commands By Source TypeLearn IR by Source Type DVD DVD SAT SatelliteOther Other AudioAudio Server Matrix Onboard = Seek DownSerial Control Strings General InformationSerial Port Communication Network CommunicationCommand Messages Command MessagesMver MgcfAMX MgbdBdhi BdloMSBSr,b MGBSrMSTRr,t MGTRrMSAOs MSSCr,sMGSCr MSSRr,sMGGLs MGSRrMSGLs,i,o MSPGr,s MGPGrMSPVr,v MGPVrMGSTr MSSTs,x MCMDs,x, yMSBLr,x MGBLrMSPRr,x MGPRrMSRGs,b8,b7 B6,b5,b4,b3B2,b1 MARGg,rMRRGr MdrgMDRGz MGRGrMDGVr,i MSGVr,vMGRSs MSFVr,s,fMGFVr,s MSLOrMCLOr MgloMSTPs MGPSs,nMRPSs,n Satellite Receiver ‘ssss’ where ‘ssss’ is the station number MSSDs,dMGSSs CSSTh,m,sCgst CCALrSgid Mcmd Command Codes Mcmd Command CodesStatus Codes for Sirius Tuner Status Codes for Sirius TunerStatus Messages Status MessagesMASOFF0 MBALr,x MPRVr,xMGSTr,v,bb,t,s,r,z,l,p MRGSz,s,b8,b7,b6MFAVr,s,f MLOTb8,b7,b6MPRSs,n,p MSTPs,tCSTv,h,m,s CALMr,s,v,h,mRSSTx,y,z RSIDx,yTroubleshooting Power ConnectionsSymptom Possible Causes Section Source Unit ConnectionsZone Connection Problems Dead ZonesLED Does Not light Source ConnectionsNo Keypad Activity At All Keypad Lights, No SoundProgramming Troubleshooting Tango Series Audio Controllers It’s Your World Take Control

DAS-T0808-SIG, DAS-T0804-SIG specifications

The AMX DAS-T0804-SIG and DAS-T0808-SIG are the forefront of advanced data distribution systems, designed to cater to the dynamic needs of commercial audio-visual installations. These models provide exceptional performance in managing and distributing various signals efficiently, ensuring seamless integration with a wide array of multimedia components.

One of the standout features of the DAS-T0804-SIG is its ability to support up to four output signals, while the DAS-T0808-SIG extends this capability to eight outputs. This scalability makes both units ideal for projects requiring flexible signal routing, whether for corporate environments, educational institutions, or entertainment venues.

Both models leverage cutting-edge digital signal processing (DSP) technologies to enhance audio quality and ensure fidelity during signal transmission. The units are equipped with advanced signal management features, including automatic gain control and equalization, which help maintain consistent audio levels and optimize playback across different environments. This ensures that users experience high-quality sound without the hassle of manual adjustments.

Connectivity options are plentiful, with support for both HDMI and analog inputs. The HDMI ports allow for seamless integration with high-definition video sources, while the analog inputs cater to older equipment, making the DAS-T0804-SIG and DAS-T0808-SIG versatile choices for mixed-system setups. The ability to handle diverse input types helps manage the challenges of modern AV environments, where devices can vary widely.

Another notable characteristic is the intuitive user interface that facilitates easy configuration and operation. The models come equipped with LED indicators for monitoring signal status, which provide real-time feedback and help troubleshoot issues swiftly. This user-centric design is particularly beneficial for installation professionals who require efficient workflows.

The DAS-T0804-SIG and DAS-T0808-SIG are also built with robust security features to protect against unauthorized access and ensure integrity in signal transmission. This is increasingly crucial in settings where sensitive information may be communicated.

In summary, the AMX DAS-T0804-SIG and DAS-T0808-SIG systems are powerful, flexible, and secure solutions for modern AV installations, characterized by their advanced signal processing, versatile connectivity, and intuitive design. Their ability to accommodate a variety of applications makes them an essential tool for any professional seeking to optimize audio-visual performance.
Top Page Image Contents