AMX DAS-T0808-SIG manual Tone Control & SRS Setting, SRS Bass Boost, Focus, 3D and WOW Settings

Page 29

Installation

Tone Control & SRS Setting

To access the Tone Control and SRS settings, press the TONE button. This enables the Tone Control Mode with BASS as the first mode selected. There are 3 Tone Control Modes available for adjustment, and 4 SRS options, as follows:

BASS: Increase / Decrease from -10dB to +10dB (Up/Down NAV buttons)

Treble: Increase / Decrease from -10dB to +10dB (Up/Down NAV buttons)

Balance: Left / Right (Up NAV button = right, Down NAV button = left)

SRS options: BASS Boost, Focus, 3D, WOW

The Source buttons on the Metreau keypad provides visual feedback as to which mode it is currently in. The following sources will light based on the current mode:

Source 1 = BASS Source 2 = Treble Source 3 = Balance Source 4 = SRS

When first entering Tone Control Mode, BASS mode is active (Source 1 LED is lit). To move from mode to mode, select the Center NAV button. This saves the setting and moves to the next mode.

Note: While in each of the modes, press and hold the Center NAV button to return to the default for that mode.

SRS (Bass Boost, Focus, 3D and WOW) Settings

Use the UP Nav button to cycle through the SRS Settings: BASS Boost, Focus, 3D, WOW (in that order).

Use the Down NAV button to cycle backwards to the previous SRS setting.

Press and hold the Center NAV button to disengage/clear the SRS settings (none of the SRS modes will be engaged).

Press the Center NAV button to save SRS Mode & exit from Tone Control set-up.

Only one SRS mode can be engaged per room/zone. Each room/zone, however, can have a different SRS mode.

The Volume LED's are used to provide feedback as to which SRS setting is active: No LED = SRS Off

LED1 = BASS boost LED 1&2 =Focus LED 1,2&3 =3D LED 1,2,3&4 =WOW

Moving from one SRS position to another disengages the original setting i.e. moving from WOW to BASS BOOST, disengages WOW.

Zone Control

To turn a single Zone ON, press any Source button (or press the Power Button).

Note: If the Power button is pressed, the zone will turn ON and will remember which source was previously ON.

To turn a single Zone OFF, press the Power button.

To turn a specific Source ON in all Zones, press and hold any Source button (the selected source will turn on and play in all zones).

To turn a specific Source OFF in all Zones, press and hold the active Source button.

To Turn All Zones OFF (System OFF), Press the "OFF" button. All zones will be turned off, and no sources will play.

Note: One minute after an ALL OFF has been performed, the Controller and all Sources will be powered down

Note: Pressing Source Buttons switches between sources and turns the Source On, but does not toggle between ON and OFF.

Tango Series Audio Controllers

17

 

 

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Tango AMX Limited Warranty and Disclaimer Important Safety Instructions Important Safety Instructions Table of Contents System Integration Drawings Tuner Modules IR Commands By Source Type Mdrg Troubleshooting No Keypad Activity At All Table of Contents Viii Tango Series Audio Controllers Overview Tango Series Audio ControllersTango Audio Controllers Product Specifications Product SpecificationsFront Panel Components Rear Panel ComponentsDAS-TRMK Rack Mount Kit for Tango Audio Controllers and Zone Tango Series Audio Controllers Ventilation InstallationRack-Mounting Cabling Installation Instructions Speaker Wire Technology SWTConnector Layout Rear Panel Cable TypeConnecting Zone Outputs Connecting Sources Audio Inputs/OutputsConnecting IR Outputs Connecting SWT Speakers to SWT Keypads SWT ConnectorsConnecting SWT Keypads to the Tango Controller Connecting Tango Zone Expanders Connecting Paging Inputs/OutputsFrom Audio Device L/R To Zones DAS-T0804-SIG 4-Zone Controller Zone Expander AddressingDAS-T0808-SIG 8-Zone Controller Antenna Installation Connecting the RS-232 Serial PortOn-Board AM/FM Tuner Module RS-232 CableWiring Diagram Connecting a Tango AmplifierMIO R-1 Audio Specifications MIO-R1 Audio Tango Distributed Audio Remote ControlSpecifications Installing Custom Buttons Inserting Batteries into The MIO R-1 Audio Programming The MIO R-1 Audio Using KeypadBuilderBattery Low Indicator Zone Control Tone Control & SRS SettingSRS Bass Boost, Focus, 3D and WOW Settings Internal Tuner and Audio Server Source ControlCD and DVD Satellite and OtherConfiguration Mode Direct Numeric AccessLED Sleep Mode Brightness Battery TypeLED Awake Brightness Additional DocumentationUsing the Audio Zone Expander Using Four Conductor Speaker WireSystem Integration Drawings SWT Distributed Audio SystemsDistribution Wiring SWT Special Wiring ConfigurationsAuxiliary Amplifier Configuration RF InterferenceWire Configurations Keypad for Control Only Remote Amplifier ConfigurationSplit Zone / Analog Volume control Option 2 one Keypad Split Zone / Analog Volume Control Option 1 One KeypadSource Documentation Setup and ConfigurationKey-By-Key Programming Programming WorksheetsProgramming Panel Programming the Tango ControllerMain Menu screen System Setup MRC Setup Mode screen System Setup Mode screenProgramming Source Equipment MRC Setup Mode Options screenIR OK 50 percent sure 1 command received Learn IR CommandsAdjusting Input Attenuation Setting Gain/AttenuationInput Attenuation Mode screen Adjusting Output GainPaging Setting Paging VolumeRoom Control Settings Setting Presets System Setup Tuner Setup Mode screenSelecting AM/FM Selecting Stereo/MonoSetting System Time System Setup Clock Setup Mode screenSetting System Date Setting the Day of the weekBacklight Intensity Backlight OptionsDevice Status Backlight ModeAbout Options screen Program LCD KP System Setup Mode AboutSetup and Configuration Tango Series Audio Controllers DAS-SIRIUS Tuner Tuner ModulesDAS-AMFM Tuner Top = Slot Bottom = Slot Front Audio Controller Jumpers Location Setting the JumpersAudio Controller Jumpers ON/OFF Settings DAS-AMFM Tuner Module Jumpers Audio Controller Jumpers Dual Tuner SettingRemoving the Pre-Installed DAS-AMFM Tuner Module Rear Panel Tuner Slots 1 Installing a Second DAS-AMFM Tuner ModuleRibbon Cable Tuner Cable Routing Installing the DAS-SIRIUS Tuner ModuleModule Connecting and Positioning the Sirius AntennaActivating Your Sirius Subscription Port Mapping AMX Duet Module Interface SpecificationsChannels Mi-Series & Tango Controllers Port MappingTango Controllers Channels Mi-Series & Tango Controllers Command Control Command ControlLevels Mi-Series & Tango Controllers Levels?INPUT ?FWVERSIONInput Passback?PROPERTY TunerpresetsaveReinit ?VERSIONMi-Series & Tango Controllers Command Feedback Command FeedbackBand FwversionProperty ProductidTunemode VersionOther External Source Commands Referenced by Source TypeInput Source Types CD CD IR Commands By Source TypeLearn IR by Source Type SAT Satellite DVD DVDOther Other AudioAudio Server = Seek Down Matrix OnboardGeneral Information Serial Control StringsSerial Port Communication Network CommunicationCommand Messages Command MessagesMver MgcfMgbd AMXBdhi BdloMGBSr MSBSr,bMSTRr,t MGTRrMSSCr,s MSAOsMGSCr MSSRr,sMGGLs MGSRrMSGLs,i,o MGPGr MSPGr,sMSPVr,v MGPVrMGSTr MCMDs,x, y MSSTs,xMGBLr MSBLr,xMSPRr,x MGPRrB6,b5,b4,b3 MSRGs,b8,b7B2,b1 MARGg,rMdrg MRRGrMDRGz MGRGrMSGVr,v MDGVr,iMGRSs MSFVr,s,fMSLOr MGFVr,sMCLOr MgloMSTPs MGPSs,nMRPSs,n MSSDs,d Satellite Receiver ‘ssss’ where ‘ssss’ is the station numberCSSTh,m,s MGSSsCgst CCALrSgid Mcmd Command Codes Mcmd Command CodesStatus Codes for Sirius Tuner Status Codes for Sirius TunerStatus Messages Status MessagesMASOFF0 MPRVr,x MBALr,xMGSTr,v,bb,t,s,r,z,l,p MRGSz,s,b8,b7,b6MLOTb8,b7,b6 MFAVr,s,fMPRSs,n,p MSTPs,tCALMr,s,v,h,m CSTv,h,m,sRSSTx,y,z RSIDx,yPower Connections TroubleshootingSymptom Possible Causes Section Source Unit ConnectionsDead Zones Zone Connection ProblemsLED Does Not light Source ConnectionsKeypad Lights, No Sound No Keypad Activity At AllProgramming Troubleshooting Tango Series Audio Controllers It’s Your World Take Control

DAS-T0808-SIG, DAS-T0804-SIG specifications

The AMX DAS-T0804-SIG and DAS-T0808-SIG are the forefront of advanced data distribution systems, designed to cater to the dynamic needs of commercial audio-visual installations. These models provide exceptional performance in managing and distributing various signals efficiently, ensuring seamless integration with a wide array of multimedia components.

One of the standout features of the DAS-T0804-SIG is its ability to support up to four output signals, while the DAS-T0808-SIG extends this capability to eight outputs. This scalability makes both units ideal for projects requiring flexible signal routing, whether for corporate environments, educational institutions, or entertainment venues.

Both models leverage cutting-edge digital signal processing (DSP) technologies to enhance audio quality and ensure fidelity during signal transmission. The units are equipped with advanced signal management features, including automatic gain control and equalization, which help maintain consistent audio levels and optimize playback across different environments. This ensures that users experience high-quality sound without the hassle of manual adjustments.

Connectivity options are plentiful, with support for both HDMI and analog inputs. The HDMI ports allow for seamless integration with high-definition video sources, while the analog inputs cater to older equipment, making the DAS-T0804-SIG and DAS-T0808-SIG versatile choices for mixed-system setups. The ability to handle diverse input types helps manage the challenges of modern AV environments, where devices can vary widely.

Another notable characteristic is the intuitive user interface that facilitates easy configuration and operation. The models come equipped with LED indicators for monitoring signal status, which provide real-time feedback and help troubleshoot issues swiftly. This user-centric design is particularly beneficial for installation professionals who require efficient workflows.

The DAS-T0804-SIG and DAS-T0808-SIG are also built with robust security features to protect against unauthorized access and ensure integrity in signal transmission. This is increasingly crucial in settings where sensitive information may be communicated.

In summary, the AMX DAS-T0804-SIG and DAS-T0808-SIG systems are powerful, flexible, and secure solutions for modern AV installations, characterized by their advanced signal processing, versatile connectivity, and intuitive design. Their ability to accommodate a variety of applications makes them an essential tool for any professional seeking to optimize audio-visual performance.
Top Page Image Contents