EdgeStar IB450SS owner manual Operation, Recessed installation, Built-in installation

Page 15

provided you have access to a water supply and a drain. You must follow the stated instructions for

a- Electrical requirements b- Water supply and drain c- Leveling the icemaker.

Recessed installation:

A recessed installation will allow you to install the ice maker under a counter, or in a kitchen cabinet provided the required clearance space around the ice maker is respected. This installation has the same requirements as a built-in installation.

Built-in installation:

If this method of installation is chosen, it will still be necessary to allow adequate ventilation space around the unit (make sure there is at least some ventilation room for the back of the unit). The following additional items must be observed.

1.Place ice maker in front of installation location. Remove the feet and place the unit flat on the floor or on a platform depending on your installation requirements.

2.The water supply pipe must be plumbed before connecting to the ice maker. Install the drain line into your drain.

3.Turn on main water supply and tap. Check for water supply connection leaks. Tighten any connections (including connections at the tie-in).

4.If electrical outlet for the ice maker is behind the cabinet, plug in the ice maker.

5.Push the ice maker into position.

6.Seal all around the cabinet to the floor with an approved caulking compound.

OPERATION

Final Check List before Operation

1.Have all packing materials and tape been removed from the interior and exterior of the ice maker?

2.Did you clean the ice storage bin?

3.Have the installation instructions been followed, including connecting the machine to water and electricity? Does the unit have proper drainage?

4.Has the machine been leveled?

5.Is the ice maker in a site where the ambient temperature is between 50º F and 100ºF and the water temperature between 41º F and 90º F all year round?

6.Has the water supply pressure been checked to ensure a minimum of 15 psig with a static pressure not to exceed 80 psig?

7.Is there a clearance of at least 2/5” at the rear, 1” at the top and 1/5” at the sides for proper air circulation?

8.Has the power supply voltage been checked or tested against the nameplate rating? And has proper grounding been installed for the ice maker?

9.Is the ice maker plugged in?

10.Have you turned on the main water supply and the tap?

15

Image 15
Contents IB450SS Clear Ice Maker use, and maintenanceBe sure to stand the ice maker upright for at least 24 hours Installation only by a licensed plumberClear Ice Maker User’s ManualFor Your Records Page ICE MAKER SAFETY………………………………………………………………… TABLE OF CONTENTSICE MAKER SAFETY Your safety and the safety of others are very importantIMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFEGUARDS Extension Cord Power consumptionUnit weight Ice cube dimensionsNote on ice storage COMPONENT LOCATIONSUnpacking ICE MAKER INSTALLATIONExcessive Weight Hazard Remove tape and glue from your icemaker before usingCleaning before use z This icemaker should be installed by a licensed plumber onlyLocation Requirements Never use an extension cord Electrical RequirementsElectrical Shock Hazard Plug into a grounded 3-prong outlet Never remove the grounding prong from the plug. Never use an adapterLeveling the Ice Maker IMPORTANT Before you begin, unplug the ice maker or disconnect powerReversing the Door Swing Recommended grounding methodWater Supply Connections To remove door from hingesTo replace door on hinges Drain Installation TypesConnecting the water line Free-standing installationFinal Check List before Operation Recessed installationBuilt-in installation OPERATIONHow the machine Makes Ice Never turn the water supply tap off when the ice maker is workingNever touch the evaporator when the machine is running Operating MethodNormal Sounds How the machine uses the waterPreparing the Icemaker for Long Storage CLEANING AND MAINTENANCEDo not touch the power plug when your hands are wet What should be kept cleanInterior Cleaning Exterior CleaningCondenser Cleaning Water Distribution Tube cleaningIce-making system Cleaning Control Panel rear of unit Descriptions of LEDs and buttons Do not let water contact the control box TROUBLESHOOTINGBefore Calling for Service Major FunctionsProblem Possible CauseProbable Correction Plug the ice maker in. Replace fuse DESCRIPTION OF WARRANTY SERVICE LIMITED WARRANTYWHAT IS COVERED WHAT IS NOT COVEREDPage EdgeStar Products Box Austin, TX Toll Free