Creda R010E, E010E Conduit Box to Mains Terminal Block, Final Installation, List of Loose Items

Page 32

Installation Instructions

Any spare cable must be coiled either behind the oven (not more than 30cm above the base of the oven recess) or pushed into the air gap below the oven after installation.

Where a hob is fitted adjacent to or above an oven a 30 amp or 45 amp double pole switch with a minimum contact clearance of 3mm should be used to feed both units via separate suitably rated cables.

Where a hob unit is fitted above the oven unit we recommend that 85oC High Temperature PVC with insulated 3 core flexible cord to table 15 of BS 6141:1991 with a conductor size of 2.5mm2 must be used to connect the hob to the control unit.

Where a hob unit is fitted adjacent to the oven unit, then 4mm2 twin and earth cable to BS 6004 is recommended to connect the hob unit to the control unit.

In all cases adhere to routing details (see fig. 5).

Your cooker should have been checked to ensure that the voltage corresponds with your supply voltage, this is stated on the rating plate which is located on the oven front frame (lower).

Conduit Box to Mains Terminal Block

(a)The oven unit should be placed on the floor on its carton base in front of the housing cabinet. The rear of the unit should be in line with the conduit box.

(b)Ensure there is sufficient cable for any future servicing.

(c)Remove the terminal cover. Prepare the cable, pass it through the cable entry hole in the oven rear panel and fit to terminal block. Secure the cable clamp and replace the terminal cover.

4.Final Installation

(a)Using a spirit level, check that the housing cabinet is level from side to side and from front to back in its installed position.

(b)Correct any unevenness by placing spacers under the bottom of the cabinet. Make sure that the cabinet rests firmly on the floor without rocking.

(c)Before the oven is fitted the cabinet must be firmly secured to the backing wall for stability.

(d)The oven unit should now be lifted (this requires two people) into the cabinet and pushed fully home.

(e)Finally the oven unit must be secured to the cabinet. Position the oven side trims equally about the cabinet sides. This should give an overlap of approx. 1.5mm per side (see Fig. 2). Secure the oven unit to the cabinet, through the side trims, by means of the four screws provided, two each side trim.

(f)Remove all packing material from the grill and oven interior.

List of Loose Items:

4 x No.6 Pozi Head screws

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents E010E / R010E Installation & User Instructions Creda Answer Centre 08701 54 64 Creda Answer Centre 08701 54 64Contents Introduction Disposal of your productAlways Safety InformationSafety Advice Safety Information Never Features Controls Control markingsOven Timer Operation Know Your Timer SymbolsTimer Function Buttons ClockfaceSetting the Time of DAY Setting the Minute MinderAuto Cooking Programmes Electronic Clock and Automatic Oven Timer Operation Other Notes on Timer Operation Solarplus Grill Step Grill Pan and HandleGrill Pan Food Grid and Anti-Splash Tray Grilling Procedure Door Position for GrillingGrill Chart FoodUsing the Oven for Fan Cooking Temperature and timeEasy Glide Shelf Oven shelf positioning for fan ovenFan oven operation Using the Oven for other Functions Oven Temperature Conversion ChartConventional Fan Oven Temperature Chart Meat If Using Aluminium FoilOven Temperature Chart Baking Baking Fan Oven CookingBaking General Cooking Results Not SatisfactoryGrill Care and Cleaning Credaclean Oven Liners E010EHow Credaclean works CleaningCleaning the Oven Base of Main OvenMeat b Grill/Meat Pan & Oven Shelves Solarplus GrillControl Panel / Trims / Inner Door Panel & Glass Replacement of the Oven LampHOW to Clean the Lamp Lens Refit the door inner glass as follows Cleaning the DoorsRemove the door inner glass as follows Installation Instructions GeneralMains Supply Oven Unit Housing CabinetsElectrical Installation Final Installation Conduit Box to Mains Terminal BlockList of Loose Items All cases adhere to routing details see fig560mm 550mm Problem Check Something Wrong?Key Contacts

E010E, R010E specifications

The Creda R010E and E010E are advanced electric heating solutions designed to provide efficient warmth and convenience for homes and commercial spaces. These units stand out due to their modern design, user-friendly features, and energy-saving technologies, making them ideal choices for individuals looking to optimize their indoor climate.

One of the main features of the Creda R010E and E010E is the advanced heating element, which ensures rapid warmth while maintaining low energy consumption. This efficiency is largely due to the incorporation of ceramic technology, which allows the units to store heat and release it gradually even after they have been turned off. This feature not only enhances comfort but also reduces energy bills, making them economically viable choices over traditional heating methods.

Both models are equipped with a precise electronic thermostat that ensures consistent and accurate temperature control. Users can easily set their desired comfort levels, and the heating units will intelligently adjust their output to maintain those temperatures. This sophisticated temperature management is complemented by programmable timers, enabling users to schedule heating times according to their needs, ensuring warmth is available when needed while avoiding unnecessary energy use.

The design of the Creda R010E and E010E reflects modern aesthetics, featuring sleek lines and a compact profile that allows for flexible placement in various settings. The lightweight construction means they can be easily mounted on walls, freeing up floor space while integrating seamlessly into any room’s décor.

Safety is also a critical consideration in the design of these units. Both models come with built-in overheat protection, ensuring that the heaters automatically switch off if they reach unsafe temperatures. Additionally, the sturdy build quality and high-grade materials enhance their durability, ensuring reliable performance over years of use.

Finally, the Creda R010E and E010E are also easy to maintain, with features designed to minimize dust and dirt buildup. Users can easily clean the external surfaces, ensuring optimal hygiene and a healthy living environment. With these technologies and characteristics, the Creda R010E and E010E represent some of the leading options for electric heating solutions in today's market, combining efficiency, safety, and modern aesthetics.
Top Page Image Contents