Daewoo frs20 manual Join connector to water tap Get ready to install water line

Page 83

11-4. Water Line Installation

How to install Water Line

1.The water pressure should be 3kgf/cm2 or more to run the automatic icemaker.

※Checkup your tap water pressure ; if a cup of 180cc is full within 10 seconds, the pressure is OK.

2.When installing the water tubes, ensure they are not close to Any hot surface.

3.The water filter only “filters” water ; it does not eliminate any bacteria or microbes.

4.If the water pressure is not so high to run the icemaker, call the local plumber to get an additional water pressure pump.

5.The filter life depends on the amount of use. We recommend you replace the filter at least once every 6months.

※When attaching the filter, place it for easy access (removing & replacing)

6.After installation of refrigerator and water line system, select [WATER] on your control panel and press it for 2~3 minutes to supply water into the water tank and dispense water.

7.Use sealing tape to every connection of pipes/tubes to ensure there is no water leak.

8.The water tube should be connected to the cold water line.

Installation Procedure

1. Join connector to water tap

2.Get ready to install water line

1)Measure an approximate distance between the filter and the Water Tube and cut the tube off filter vertically.

2)Connect the tubes to the filter as the figure shows.

Leave a sufficient distance when cutting the tubes.

82

Image 83

Contents Refrigerator N T E N T S Page External Views FRSN-U20DB / EB FRSN-U20FB / GB Name of Each Parts Freezer Compartment Refrigerator Compartment Freezer Compartment Refrigerator Specification AC220V / 192W Specification 220~240V Models onlyDoor Switch , F / R Basic Model Dispenser ModelDisplay Operation and FunctionsFront PCB button Dispenser ModelReference Please wait Defrosting Cycle Fan Heater Defrost ModeComp Flow Chart of Defrosting Start Voltage Forced Defrosting ModeFan Voltage of Control Mode Sensor FAN, R-FAN, C-FANControl of Interior Lights FRSN-U20DA Buzzer or Alarm ControlLouver Heater Control Basic Model DemonstrationMain PCB Resistance of R-sensor Mid ON/OFF Point Compensation of R-sensor ON/OFF PointBasic Model LED Display of Inner Control Error DisplayRT-S Dispenser Model Cled Display of Front PCB Error Code ContentsBasic Model Dispenser Model Eierror Dispenser Model Front PCB Summary of FunctionBasic Model Inner Control Automatic Icemaker Dispenser Model Back up Function Basic ModelStart Ice separating drop mode Dispenser Control Function Lamp Water S/V ※ Voltage of every part Power Circuit DiagramCircuit Operation Basic Model Dispenser ModelMicom Function of Each SensorDispenser Model How it works Relay FunctionIC8 Fan Function Wiring Diagram DiagramDispenser Model Circuit Diagram of Main PCB Page Dispenser Model Page Inner View Component Locate WiewFront View Dispenser + Home bar Model Machine Compartment EvaporatorHow to check Hose Ice Maker Tube As HOW to Check Each PartsHose Ice Maker Tube Assembly Disassembling ProcedureHow to Check Hose Ice Maker Tube Assembly Bracket Geared Motor AssemblyHow to Check Micro Switch Dispenser Micro Switch▷Check Change Flap Heater AS Dispenser Solenoid Valve▷ Good 215Ω±10% SOL2003-01B 193 ~ 236Ω 88 ~ DC 12V,1.5WCheck Point Remark Main PCBCompensation Used when making R-temp. down ▷ Remove 2 screws on top front of ice maker Ice MakerOn Close How to Check Ice MakerIce Dropping Motor ▷ Good RS-360RH-14250 ~ 14Ω Blue CircleStart Faulty Start F/R lights OFF , F-PCB Power OFF※ How to replace Front PCB Trouble DiagnosisDefrost Heater 192W 252 Ω Freezer Compartment4th pipe from buttom Removing and replacing Freezer parts Removing and replacing Freezer parts Defrost Heater Ice Formation on F-Louver Start Cover and pull forward Disconnection / breaking of Freezer Lights Wires StartSwitch to pull forward Light coverRefrigerator Compartment Bulbs Disconnection / Breaking of Refrigerator Lights Wires StartRemove screws of light cover Hold the bottom Cover and pull Change the lightDoor is open too long ? Sensor is OK ? +screw driver Removing of Check ValveOperation Noise of Refrigerator Page Attach a absorber on point ③ accumulator Troubleshooting of Evaporator SoundFan Noise Start Fan is damaged Or transformed ? Troubleshooting of Fan Noise Pipe Noise Start Door Cooling Cycle Heavy Repair Contents ToolsDrier part with a nipper and then cut low pressure side Precautions During Heavy RepairBe sure to replace drier when repairing pipes Use special parts and tools for R-134a or R-600aRemove residual refrigerant more than 5 minutes later after Practical Work for Heavy RepairBe sure to charge To the low pressure sideClose valve ① An evacuated bombeElectronic leakage tester Take a leakage test on the welded or suspicious area with anCompressor Suction Pipe HighLow Brazing Reference DrawingsWidth*Depth*Height 903mm X 734.5mm X 1790mm Installation GuideInstallation Preparation Dimensions including Door Handles※Remove front bottom cover first, if it is attached If the refrigerator can not enter the doorReplacing Freezer Door Case freezer door is lower Than refrigerator door Refrigerator Leveling & Door AdjustmentLeave a sufficient distance when cutting the tubes Join connector to water tap Get ready to install water line2Insert the fastening ring into the Water tube Remove any substance from filterAttach the filter box Connect water tubeDispenser Water Flow Cabinet Machine Room / Eva Part Refrigerator Room Freezer Room Freezer Door Refrigerator Door Reference