Select Blower Option and Install Ductwork

1. SELECT BLOWER OPTION AND INSTALL DUCTWORK

Either an interior or exterior blower or in-line blower may be used with this insert. The insert model RMIP33 or RMIP45 must be installed with blower models P5, P8, HLB3, HLB6, HLB9, HLB11, 331H, 332H, 335 or 336 only. Other blowers cannot be substituted. (Blowers sold separately).

Plan where and how the ductwork will be installed. Access to the top of the hood is preferred for connection of ductwork. As an alternative, flexible metal ductwork may be used.

If installing in-line blower, refer to instructions packed with in-line blower and follow steps 1 up to 8, 13, 14, 16, 17, 19 and up of this manual.

Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. Use round ductwork, with a short section (about 4’ expanded) of flexible metal duct (optional) for attachment to the transition. Use screws to attach flexible metal duct to the rigid duct. Use 2” duct tape to seal duct joints.

The minimum hood distance above cooktop must not be less than 24”. A maximum of 30” above cooktop is highly recommended for best capture of cooking impurities.

Distances over 30” are at the installer and users discretion.

Wall cap

HH0038A

Roof cap

7” or 8” round ducts with 7” or 8” round metal flex. duct (optional)

31/4”x 10”to 7”or 8”transition or 3 1/4”x 14”to 8”transition

Insert with interior blower

24” minimum

above cooking surface

Exterior blower

10” round duct

10” round metal flex. duct (optional)

Insert with exterior blower

24” minimum above cooking surface

HH0039A

Roof cap

10” round duct

In-line blower

10” round metal flex.duct

(optional)

Wall cap

Insert

24” minimum above cooking surface

HH0058A

MODEL P5 (SINGLE) OR	MODEL 331H, 332H, 335 OR	MODEL HLB3, HLB6, HLB9 OR HLB11
P8 (DOUBLE) INTERIOR BLOWER	336 EXTERIOR BLOWER	IN-LINE BLOWER
TYPICAL DUCTWORK	TYPICAL DUCTWORK	TYPICAL DUCTWORK

2. PREPARE THE INSTALLATION

Make sure that the following items are included:

-Insert

-Accessories:

•Filters (3 for RMIP33 model, 4 for RMIP45 model)

•Bag of parts including:

(4)lock nuts, (1) wire clamp, (8) no. 8 x 3/4” standard screws, (2) wire connectors,

(2)no. 6 x 1/2” standard screws, (8) no. 8 x 3/8” screws. Discard items not used. Parts sold separately:

-Interior blower Model P5 includes blower, rough-in kit, flow deviator and 3¼” x 10” adapter

-Interior blower Model P8 includes blower, rough-in kit, flow deviator and 3¼” x 10” adapter and 3¼” x 14” adapter

-In-line blower assembly HLB3, HLB6, HLB9 or HLB11 (all include transition)

-In-line blower rough-in plate model 332KR, required for all In-line or Exterior Blowers

-Exterior blower assembly 331H, 332H, 335 or 336

-Halogen lights 120 V, 50 W, PAR 20 (2 for RMIP33 model and 3 for RMIP45 model)

-Custom hood liner Model RML3336S, RML3342S, RML4548S, RML4554S or RML4560S (optional)

-Backsplash RMP Series (optional)

-RMIPWC Remote control (optional)

-Baffle filters RBFIP Series (optional)

-Transitions, ducts (rigid and flexible), elbows, dampers, wall and roof caps. Refer to page 3 and 4 for a complete list of venting options and model numbers.

NOTE : During installation, protect countertop and/or cooktop.

- 5 -