Bakers Pride Oven Care of the Shortening, LGF and LGF-F Operation, Start-Up LGF and LGF-F

Page 17

Gas Pressure Fryer

Operation

 

 

Care of the Shortening

Solid shortening should always be returned to the filter vat while in the liquid state. If this is not done, it will have to be heated to a liquid state. When using solid shortening, the fryer must be equipped with a pump heater. After filtering with solid shortening, the filter lines must be completely emptied of shortening. The pump heater will take care of any residual shortening in the pump, but cannot melt all of the shortening in the filter lines. The pump heater accessory may be purchased separately from BKI.

To extend the life of your shortening, for the best possible flavor in your products, and for economy and efficiency of operation, we urge you to follow these recommendations:

1.Use only high-quality frying shortening without additives, of low moisture content and with a high smoke point.

2.Press excess moisture from products before breading. The more moisture released in the shortening, the quicker it will break down.

3.Filter at least once a day or once every three loads during frequent cooking.

4.Clean any residue or crust formations from the sides and bottom of the pot each time you filter the shortening.

5.Add fresh shortening as needed to maintain the proper shortening level TO THE FILL MARK ON THE POT WALL.

6.DO NOT HOLD SHORTENING AT HIGH TEMPERATURE when the fryer is not in use. If you expect an elapsed time of one hour or more between cooking, close the lid and press the “0” button on the LGF-FC model. On Models LGF and LGF-F, set the thermostat to 150º F.

7.Shortening changes are determined by the quantity and type of food prepared. Excessive boiling and foaming are definite signs of shortening breakdown.

8.After you have finished frying for the day, filter the shortening and replace the filter pad. Also, thoroughly clean the pot of sediment and crumbs and empty the condensate pan.

LGF and LGF-F Operation

Start-Up (LGF and LGF-F)

1.Make sure the main drain valve is closed.

2.Fill pot with shortening to about one inch below the fill mark.

Risk of fire exists if the oil level drops below the minimum oil level. The level of oil within the pot must not fall below 5mm of the maximum oil level.

Use of oil/shortening older than the manufacturers recommendations for life of the oil is prone to surge boiling and flash fires. Follow the oil manufacturers guidelines for lifecycle of oil/shortening.

Overfilling the fryer pot with shortening could lead to serious injury. Ensure that the fryer pot is filled with shortening only to the fill mark when shortening is hot. Do not use any shortening other than what is specified in this manual and do not overfill the fryer pot.

15

Image 17
Contents Gas Pressure Fryer Warranty Information Table of Contents Safety Signs and Messages SafetyFull Disconnection Specific PrecautionsEquipotential ground plane Safe Work Practices Do Not Store Or Use Anything Flammable Near FryerKeep The Floor Around Your Fryer Clean Shortening Do Not Over-Tighten The Spin Handle Keep Away From The Vent Be Prepared for Emergencies Safety Labels Gas Pressure Fryer Introduction Installation Operation Controls and IndicatorsFunction Item DescriptionGas Pressure Fryer Operation Start-Up LGF and LGF-F Care of the ShorteningLGF and LGF-F Operation Cooking LGF and LGF-F KEY Display Mode DescriptionGas Pressure Fryer Operation System Programming LGF-FC OperationStep Action Display Comments Product Programming Sequence Product ProgrammingComments Step Action Display Step Action Display Cooking LGF-FC Start-Up LGF-FCGas Pressure Fryer Operation Recipes Whole Duckling Whole Turkey 12 to 14 poundsPork Chops Cube Or Minute SteaksNormal Shutoff Operation After Gas or Power OutageMaintenance Assemblies Description Assembly #Lid/Arm Assembly, AN3211350S Sheet 1 Lid/Arm Assembly, AN3211350S Sheet 2 Lid/Arm Assembly, AN3211350S Sheet 3 Lid/Arm Assembly, AN3211350S Sheet 4 Item # QTY Description Item # QTY Description Drain/Motor/Piping Assembly COUPLING, 5/8 45 Flare to Burner Tray Assembly LP GAS Burner Tray Assembly Control/Insulation Panel LGF & LGF-F BEZEL, Robertshaw Thermostat Control/Insulation Panel LGF -FC CONTROLLER, VFD Less Harness HINGE, DOOR, LH, PIN Side FRY.DOORS Oil Vat Assembly AN32112800 Filter Screen ASSY, LGF Solenoid Valve Assembly Solenoid Valve Assembly Parts BALL, 11/16 Steel Bearing Drain Valve Replacement Description Accessory # AccessoriesDescription Component # ComponentsFigure # Wiring Diagram Diagram #LGF-F 120V/60HZ/1 Phase LGF-FC 120V/60HZ/1 Phase LGF-FC 220V/50HZ/1 Phase LGF-FC 220V/60HZ/1 Phase LGF-FC 240V/50HZ/1 Phase LI0196/0808