Bakers Pride Oven ALF-FC service manual Initial Test and Adjustment

Page 12

Automatic Lift Fryer	Installation

Initial Test and Adjustment

1. Fill pot with shortening to about one inch below the mark.

Risk of fire exists if the oil level drops below the minimum oil level. The level of oil within the pot must not fall below 5mm of the maximum oil level.

Use of oil/shortening older than the manufacturers recommendations for life of the oil is prone to surge boiling and flash fires. Follow the oil manufacturers guidelines for lifecycle of oil/shortening.

Overfilling the fryer pot with shortening could lead to serious injury. Ensure that the fryer pot is filled with shortening only to the fill mark when shortening is hot. Do not use any shortening other than what is specified in this manual and do not overfill the fryer pot.

The fryer has a maximum temperature setting of 375º F/190º C (for ALF and ALF-F) or 390º F/200º C (for ALF-FC). Do not use oil/shortening with a flashpoint less than 554º F (290º C)

Use only high-quality shortening that has low moisture content, a high smoke point and no additives.

2.Place the FILTER/OFF/FRY switch to the FRY position. The shortening should begin to heat and begin to reach the fill mark inside the pot. Add more shortening as required to reach the fill mark. Refer to the troubleshooting section if this does not occur.

10

Image 12

Contents Automatic Lift Fryer Warranty Information Limited ONE Year WarrantyTable of Contents Safety Precautions Safety Signs and MessagesIntroduction Specific Precautions Equipotential ground planeFull Disconnection Noncombustible Floors Only Safe Work PracticesDo Not Overload The Basket With Food Keep this manual with the Equipment Be Prepared for Emergencies Safety Labels Installation Assembly and MountingWiring Unpacking and HandlingInitial Test and Adjustment Controls and Indicators OperationCanceling The Stir OIL Function Pressing this button cancels Item # Description FunctionAutomatic Lift Fryer Operation Care of the Shortening ALF-F OperationStart-Up KEY Display Mode Description Cooking ALF-FC Operation System ProgrammingStep Action Display Comments Product Programming Product Programming SequenceProgram Product # Step Action Display Comments ALF and BLF AutomaticStart-Up Automatic Lift Fryer Operation Maintenance Scheduled MaintenanceDaily WeeklyFiltering Procedure To refill the pot automatically, use the steps belowBoil-Out Procedure Automatic Lift Fryer Maintenance Filter Pad Replacement Troubleshooting Problem Cause Possible Solution Shortening Heating TooSlowly Filter System Not WorkingReplacement Parts Description Assembly #Assemblies Item # QTY Description Door Assembly SB1289 Door Assembly SB1289 Parts Drain/Motor/Piping Assembly Item # QTY Description Control Panel ALF-F KNOB, S/S Strat T0075 Control Panel ALF-FC Control Panel ALF-FC Parts Oil Vat Assembly AN86202800 Quik Disconnect Bracket Weldment Components Description Component #Components Accessories Description Accessory #Storage Cover Assembly Optional Storage Cover Assembly Parts Wiring Diagrams Wiring Diagram Diagram #ALF-F 208V 3 Phase or ALF-F 240V 3 Phase ALF-F 208V/240V, 1/3 Phase ALF-FC 208V 1/3 Phase or ALF-FC 240V 1/3 Phase Sheet 1 ALF-FC 208V 1/3 Phase or ALF-FC 240V 1/3 Phase Sheet 2 ALF-FC 208V 1/3 Phase or ALF-FC 240V 1/3 Phase Sheet 3 ALF-FC 208V/240V/3 Phase sheet 1 ALF-FC 208V/240V/3 Phase sheet 2 ALF-FC 208V/240V/3 Phase sheet 3 Automatic Lift Fryer Automatic Lift Fryer Automatic Lift Fryer Automatic Lift Fryer LI0228/0808