Vermont Casting LHECDV20 Round Vent Termination Installation, Ceramic Refractory Installation

Page 11

Round Vent Termination Installation

Round Vent Termination Model HEDVRT is designed to be installed onto the LHECDV20, LHERDV20, LH- ECDV30 and LHERDV30 direct vent insert fireplaces. This round vent termination is built to be installed onto any type A-vent round chimney or B-vent round chim- ney. The minimum inside venting diameter must be at least 7" (178 mm) and the maximum outside diameter venting should not exceed 14" (356 mm).

The extended cap 14" (356 mm) wide is only to be used when the outside diameter of the round chim- ney is more than 11" (279 mm).

Install the extended cap 14" (356 mm) with the round vent termination by setting the vent termination on top of the extended cap, then secure it with three

(3) screws (provided) through the mounting bracket holes and seal around the edges of the vent termina- tion with the silicone provided. (Fig. 18)

Secure the Cap with

Three (3) Screws

Provided

Seal Around the Edges of the Cap with Silicone

FP1326

Fig. 18 Round vent termination with extended assembly.

LHEDV Series Direct Vent Insert

Ceramic Refractory Installation

1.Remove front glass.

2.Remove logs from unit.

3.Remove refractory from package.

Refractory are fragile and must be handled with care. Where at all possible, two hands should be used when handling.

4.Take center refractory and tilt so bottom edge seats onto the rear log bracket at the back wall of the fire- place. (Fig. 19)

5.Press center refractory to back side of fireplace and hold in place.

6.Take left or right refractory and align it so leading edge faces outward. (Place refractory in fireplace side and slide it back to support the center refrac- tory.)

7.Repeat step 6 for remaining side refractory.

8.Fasten bracket supports against refractory top to hold side in place.

When side refractory is installed correctly, the center refractory will be supported by the side refractory.

 

Leading Edge

Leading Edge

 

 

 

 

 

Bottom Edge

 

Left Side

Center

Right Side

 

 

 

FP1329

Fig. 19

Ceramic refractory.

 

10004894

11

Image 11
Contents LHERDV30 LHECDV20 LHECDV30 Table of Contents Please Read the Following Carefully Installation & Operating InstructionsLocating Your Gas Fireplace Insert With Zero Clearance Kit Insert ApplicationsMinimum Fireplace Insert Opening Fireplace & Trim DimensionsAn alternate air supply is recommended with this component MantelsFraming & Finishing Zero Clearance ApplicationsHigh Elevations Gas Line InstallationGas Specifications Gas Inlet & Manifold PressuresFan Removal Instructions Installation of Trim Switch For RN/RP Gas ValvesGas Supply Pressures Fan KitVenting Installation Exhaust Liner InstallationMinimum Vent Height Feet Maximum Vent Height Exhaust Ceramic Refractory Installation Round Vent Termination InstallationVenting Components Operating Instructions LHECDV30, LHERDV30 Fig Large Lava Rock PlacementFlame Adjustment RN/RP Models First Firing Flame CharacteristicsWhat to do if YOU Smell GAS To Turn Off Gas To HeaterSymptom Possible Causes Corrective Action Troubleshooting the Gas Control SystemHoneywell Millivolt Valve Instructions for RF Comfort Control Valve Shut Off ProcedureTransmitter Operation Off Mode On Manual ModeChange Between F/C Temperature Units Delay Timer ModeAuto Mode Fan Override During Auto ModeAuto Path LED Count Service Action Replace valveLocal Path On Path Burner and Burner Compartment MaintenanceTrim Cleaning Cleaning the Standing Pilot Control SystemLhedv Series LHERDV20 LHECDV20 LHERDV30 LHECDV30 DescriptionLHER20 LHEC20 LHER30 LHEC30 LHE SeriesOptional Accessories Lhedv Series Direct Vent Insert Lhedv Series Direct Vent Insert Lhedv Series Direct Vent Insert If Warranty Service is NEEDED… Product Covered by this WarrantyAFUE% Efficiency Ratings

LHECDV20, LHERDV30, LHECDV30, LHERDV20 specifications

Vermont Castings is renowned for its commitment to offering high-quality, efficient, and aesthetically pleasing gas fireplaces. Amongst its esteemed lineup, the LHECDV20, LHERDV20, LHECDV30, and LHERDV30 stand out for their exceptional features and innovative technologies that cater to a wide range of consumer needs.

The LHECDV20 and LHECDV30 models are designed for those seeking a compact yet powerful heating solution. Both units embody Vermont Castings' signature cast-iron construction, which not only enhances durability but also provides excellent heat retention. The LHECDV20 has a smaller footprint ideal for smaller spaces, while the LHECDV30 offers a broader heating range, making it suitable for larger areas. Each model features a stunning view of the flames, achieved through large glass doors that create a warm and inviting atmosphere.

Both models utilize advanced burner technology that maximizes efficiency and minimizes emissions. The unique design ensures uniform heat distribution, which is complemented by an adjustable flame height feature. This allows you to customize the ambiance according to your preference, whether you desire a roaring fire or a gentle warmth.

The LHERDV20 and LHERDV30, on the other hand, come equipped with a realistic log set and more intricate burner systems. These units replicate the organic look of a traditional wood fire, ensuring that aesthetics do not compromise performance. The radiant heat technology in these models ensures the warmth is felt throughout the room while maintaining an eco-friendly approach to heating.

Safety features are a paramount consideration in the design of all Vermont Castings models. Each unit is equipped with an advanced safety pilot system that provides peace of mind for homeowners. Additionally, the easy-to-use remote control allows users to operate the fireplaces from the comfort of their chair, making heating your space convenient and hassle-free.

Installation is made easy with top-venting options available for each model, allowing flexibility in settings. Vermont Castings also offers an array of customizable options, enabling you to personalize your fireplace to match your home’s decor.

In summary, the Vermont Castings LHECDV20, LHERDV20, LHECDV30, and LHERDV30 gas fireplaces offer a harmonious blend of efficiency, beauty, and technology. Their commitment to quality ensures that you not only enjoy the warmth but also the elegance that these fireplaces bring to your living environment. Whether you have a cozy cabin or a spacious home, these models offer a solution to meet your heating needs while enhancing the aesthetic appeal of your space.