TC electronic SDN BHD SDN BHD user manual Important Safety Instructions

Page 26

IMPORTANT SAFETY INSTRUCTIONS

Please read, keep, and follow these instructions before connecting this unit. Heed all warnings and instructions. Retain this notice and the owner´s manual for future reference.

The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

Warning!

To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture.

Do not open the unit - risk of electric shock inside.

This apparatus must be earthed.

Use a three wire grounding type line chord like the one supplied with the product.

Be advised that different operating voltages require the use of different types of line cord and attachment plugs. If in doubt please contact your TC distributor.

Check the voltage in your area and use the correct type. See table below:

Voltage

Line plug according to standard.

 

 

110-125V

UL817 and CSA C22.2 no 42.

 

 

220-230V

CEE 7 page VII, SR section 107-2-D1/IEC 83 page C4.

 

 

240V

BS 1363 of 1984. Specification for 13A fused plugs and switched and un-switched socket outlets.

 

 

Mount in a well ventilated rack with a little space above and below.

This equipment should be installed near the socket outlet and disconnection of the device should be easily accessible.

Do not install near heat source, such as radiators, heat registers, stoves or other apparatus. (including amplifiers) that produce heat.

Do not rely solely on the front screws when mounted in touring rack. Support the back as well.

Clean only with a damp cloth.

Do not defeat the safety purpose of a polarized or grounding type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades/prongs and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Unplug this apparatus during lightning storms or when unused for long periods of time.

26

Image 26
Contents Triplec Page Table of Contents Page Introduction Front Panel Ratio knob Envelope Mode keyLook Ahead key Attack knobStereo Version Rear PanelSingle Version Midi CableSignal Flow Triplec in a Digital Insert Triplec SetupsSetting up the Triplec Triplec Stereo version in a Group InsertSide Chain On Stereo Setup Using two Triplec Single ChannelsEQ Insert in the Triplec Sidechain Triplec Display Setup SetupBulk Dump Midi CC Range On/OffProgram bank SysEx IDEdit Recall Edit StoreRecall StoreDynamic Section FULL-RANGE ModeInput Section Makeup Gain SectionEdit Menu External SidechainTo select Multi-band mode MULTI-BAND ModeSpectral Adjust Peak TypeHi X-Over Makeup GainMeters Lo X-OverEnvelope Attack Gain Envelope ModeTo select the Envelope mode Sustain PeriodHi X-Over, Lo X-Over and Comp Style are External EQ Sidechain OperationStereo Link Compressors vs Limiters Using Compression IntroductionCompression in general Multi-band CompressionSelecting Full-range or Multi-band mode Using CompressionSpectral Adjust Section Better Definition of Vocal materialMakeup Gain Hard Compression of Vocal TracksControlling Percussive Material Important Safety Instructions Voltage Line plug according to standardCertificate Of Conformity ServiceFor the customers in Canada Appendix Midi Implementation Chart Appendix Midi Control Changes Midi CCAppendix Technical Specifications Digital Inputs and Outputs GeneralPreset List