TC electronic SDN BHD SDN BHD user manual Front Panel

Page 6

FRONT PANEL

POWER key

SYNC

TRIG

	On/Off switch for the unit.	Indicates the current clock of	Indicates when the Envelope
	INPUT LEVEL knob	the TRIPLE•C. When locked to	function is processing the
	INPUT LEVEL knob	an external clock, the "DI" icon	incoming signal.
	Adjusts the Input level.	is lit and the incoming Sample	LIMIT
	Range is -6dB to +18dB.	Rate is displayed by either the	LIMIT
	INPUT/OUTPUT meters	44.1 or 48 icon.	When the LIMIT LED is lit the
	INPUT/OUTPUT meters	If no or unacceptable clock is	Envelope Softclipper is active.
	Peak meter showing Input and	available, the "Digital" and "DI"	MULTI-BAND OFF key
	Output level. The meter range is:	icons will be blinking.	MULTI-BAND OFF key
	0, -3, -6 ,-12, -18, -24, -40dB.	LINK indicator	Turns the Multi-band mode
	For the Stereo version this meter	LINK indicator	on/off i.e. activates the full
	is common for both channels.	Indicates that the unit is linked	band mode. When the LED is lit
	INPUT OVERLOAD LED	to a second TRIPLE•C.	the Multi-band algo is inactive.
	INPUT OVERLOAD LED	MIDI	PEAK SENSITIVE key
	The OVERLOAD LED indicates	MIDI	PEAK SENSITIVE key
	one of two situations: The Input	When MIDI information is	The TRIPLE•C is basically an
	level is too hot and therefore over-	received the MIDI icon will	RMS based Compressor, mean-
	loading or there is an internal DSP	blink.	ing that it responds to average
	overflow. The OVERLOAD LED is	Gain Metering	level of the incoming source
	lit when 1 sample is @ 0dBFS.	Gain Metering	material. This key turns the
	OUTPUT OVERLOAD LED	The Gain meter indicates the	TRIPLE•C into a Peak based
	OUTPUT OVERLOAD LED	total gain through the TRIPLE•C	Compressor. When the LED is
	Indicates that the Output is too	and simultaneously shows the	lit the TRIPLE•C is in Peak
	hot. This will occur if e.g. too	gain reduction.	mode. This feature is only
	much gain has been added	Envelope Section	available in Multi-band mode.
	through the TRIPLE•C.	Envelope Section	SOFTLIM key
	The OVERLOAD LED is lit when	Indicates the setting of the	SOFTLIM key
	1 sample is @ 0dBFS.	Envelope Mode. Please see	Activates/deactivates the Soft-
	INPUT - Analog/Digital	Envelope chapter in the	Limiter in the Output section
	INPUT - Analog/Digital	manual for further information.	When the LED is lit, the Soft-
	Indicates whether the TRIPLE•C is		Limiter is active.
	set to analog or digital Input.
	When set to digital Input, the
	Sample Rate automatically
	switches to DI. In case of no or
	unacceptable clock the "Digital"
	and "DI" icon will be blinking.

6

Image 6

Contents Triplec Page Table of Contents Page Introduction Front Panel Ratio knob Envelope Mode keyLook Ahead key Attack knobStereo Version Rear PanelSingle Version Midi CableSignal Flow Triplec in a Digital Insert Triplec SetupsSetting up the Triplec Triplec Stereo version in a Group InsertStereo Setup Using two Triplec Single Channels EQ Insert in the Triplec SidechainSide Chain On Triplec Display Setup SetupBulk Dump Midi CC Range On/OffProgram bank SysEx IDEdit Recall Edit StoreRecall StoreDynamic Section FULL-RANGE ModeInput Section Makeup Gain SectionEdit Menu External SidechainTo select Multi-band mode MULTI-BAND ModeSpectral Adjust Peak TypeHi X-Over Makeup GainMeters Lo X-OverEnvelope Attack Gain Envelope ModeTo select the Envelope mode Sustain PeriodHi X-Over, Lo X-Over and Comp Style are Sidechain Operation Stereo LinkExternal EQ Compressors vs Limiters Using Compression IntroductionCompression in general Multi-band CompressionSelecting Full-range or Multi-band mode Using CompressionSpectral Adjust Section Better Definition of Vocal materialHard Compression of Vocal Tracks Controlling Percussive MaterialMakeup Gain Important Safety Instructions Voltage Line plug according to standardService For the customers in CanadaCertificate Of Conformity Appendix Midi Implementation Chart Appendix Midi Control Changes Midi CCAppendix Technical Specifications Digital Inputs and Outputs GeneralPreset List