TC electronic SDN BHD D22 user manual Important Safety Instructions, Service

Page 3

IMPORTANT SAFETY INSTRUCTIONS

The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

1Read these instructions.

2Keep these instructions.

3Heed all warnings.

4Follow all instructions.

5Do not use this apparatus near water.

6Clean only with dry cloth.

7Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11Only use attachments/accessories specified by the manufacturer.

12Unplug this apparatus during lightning storms or when unused for long periods of time.

13Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

This apparatus must be earthed.

Use a three wire grounding type line cord like the one supplied with the product.

Be advised that different operating voltages require the use of different types of line cord and attachment plugs.

Check the voltage in your area and use the correct type. See table below:

Voltage

Line plug according to

 

standard.

110-125V

UL817 and CSA C22.2 no 42.

220-230V

CEE 7 page VII, SR section

 

107-2-D1/IEC 83 page C4.

240V

BS 1363 of 1984.

 

Specification for 13A fused

 

plugs and switched and

 

unswitched socket outlets.

This equipment should be installed near the socket outlet and disconnection of the device should be easily accessible.

Do not install in a confined space.

Do not open the unit - risk of electric shock inside.

Caution:

You are cautioned that any change or modifications not expressly approved in this manual could void your authority to operate this equipment.

Service

There are no user-serviceable parts inside.

All service must be performed by qualified personnel.

a

Image 3
Contents USER’S Manual Page Service Important Safety InstructionsCertificate Of Conformity For the customers in CanadaTable of Contents Page Introduction Main FeaturesFront Panel Power & Memory Card Electronic Power switch »Easy touch«Bypass Jack unbalanced XLR Output Balanced XLR XLR Rear PanelSignal path is 24 bit Signal FlowOutput Analog Input Analog SetupsInstallation note Input AnalogInput Analog Sample Rate Sync Input Digital Sample Rate EXT DIInput Digital Sample Rate Sync Sample Rate Conversion On Basic Operation Control Adjust wheel Bypass Bypasses the unitKeyboard Lock Function Recalling a preset Presets In GeneralRecall Locked mode Seamless preset changesFader Storing User Presets Using a Memory cardStore Dither SetupSample Rate Conversion ClockPress the I/O key twice to enter this Analog Analog OutDigital I/O Utility Time ResolutionControl Resolution Tap DelayMemory Backup GPI External InputMeter Preset changes are not seamless You cannot turn the power offNo sound through the D22 Appendix Technical specifications Key test Delay + Control wheel testBattery test Service noteCompressor Overshoot Sys-Ex System Exclusive Midi CommandsTos-link Bits & BytesMidi Cable Pedal CableFader Cable Jack unbalanced XLR Output Jack balanced XLR Examples Frequently Asked QuestionsActivating the Master Fader Why make a Master Fader?Connecting and Calibrating the Master Fader Master Fader