Texas Instruments TRF1500 manual Low-Band Cascaded RF Input Return Loss

Page 29

SWRA004A

Low-Band Cascaded: RF Input Return Loss

Control state: 011000

The input return loss of the low band receiver is measured at the EVM low band RF input port, J10. The measurement is performed using a network analyzer.

Set up the network analyzer as follows to measure the RF input return loss:

1)Set the network analyzer to measure the low band RF frequency (see Table 3).

2)Set the power range to -35 dBm through -20 dBm, and then set the input power to -30 dBm.

3)Perform a full one-port calibration on port 1 of the network analyzer.

4)Set the network analyzer to measure S11.

5)Connect the EVM RF input, J10, to port 1 of the network analyzer.

6)Measure the RF input return loss.

Low-Band Cascaded: LO Input Return Loss

Control state: 011000

The cascaded LO input return loss of the Low Band is measured at the EVM low band LO input port, J12. The measurement is performed using a network analyzer.

1)Set the network analyzer to measure the low band LO frequency (see Table 3).

2)Set the power range to -35 dBm through -20 dBm, and then set the input power to -30 dBm.

3)Perform a full one-port calibration on port 1 of the network analyzer.

4)Set the network analyzer to measure S11.

5)Connect the EVM LO input port, J12, to port 1 of the network analyzer.

6)Measure the LO input return loss.

30	TRF1500 Integrated Dual-Band RF Receiver User’s Guide

Image 29

Contents TRF1500 Integrated Dual-Band RF Receiver User’s Guide Important Notice Trademarks PIC Telephone Contents Appendix a Test Bench Configuration Tables FiguresAbstract TRF1500 Integrated Dual-Band RF Receiver User’s GuideIngl E Chip Anal OG AS E B Product SupportWorld Wide Web Related DocumentationIntroduction Board Design and Impedance Matching Design ConsiderationsExternal Components TRF 1500 Dual-Band Receiver TRF1500 Dual-Band Receiver Block DiagramPin Number Name Description Pin DescriptionsStrong Signal Control State and the Corresponding Active Circuits TRF1500 Control StateCascaded Block Diagram of the Low-Band Receiver Section Low-Band LNA Turn on Time Low-Band LNALow-Band LNA Output Low-Band LNA InputSurface Acoustic Wave SAW Filter Low-Band LNA Output ConfigurationLow-Band Mixer RF Input Low-Band MixerLow-Band if Output Low-Band Mixer LO InputLow-Band LO Buffer Amplifier Output Low-Band if Output ConfigurationLow-Band Buffer Amplifier Output Configuration LB LNA, LB Mixer, SAW Filter, and LB if Amp Parameters LOW-Band Cascaded Power Conversion GainLow-Band Cascaded Test Guide Low-Band Cascaded Power Conversion Gain Reduction Low-Band Cascaded Noise Figure TRF1500 Integrated Dual-Band RF Receiver User’s Guide Low-Band Cascaded LO Input Return Loss Low-Band Cascaded RF Input Return LossLow-Band Power Leakage LO In to RF LOW Band LO Buffer Output PowerLow-Band Cascaded Third Order Input Intercept Point IIP3 Low-Band Cascaded 1dB RF Input Compression Point Low-Band Cascaded 1dB Blocking Point Block Diagram of the High-Band Receiver Section High-Band LO Input High-Band RF InputHigh-Band LO Frequency Doubler Driven Configuration High-Band if Output High-Band if Output ConfigurationHigh-Band LO Buffer Amplifier Output High-Band LO Buffer Amplifier Output ConfigurationHB LNA, HB mixer, HB if amp High-Band Cascaded Power Conversion GainHigh-Band Cascaded Test Guide High-Band Cascaded Power Conversion Gain Reduction High-Band Cascaded Image Rejection High-Band Cascaded Noise Figure High-Band Cascaded RF Input Return Loss High-Band LO Buffer Output Power High-Band Cascaded Third Order Input Intercept Point IIP3 High-Band Cascaded Power Leakage LO In to RFHigh-Band Cascaded 1dB Input Compression Point High-Band Cascaded 2X2 Spur Performance High Band 3X3 Spur Performance Low-Band and High-Band Transmit Mixer RF Input Low-Band and High-Band TransmitLow- and High-Band Transmit Mixer Low- and High-Band Transmit Mixer if Output Configuration Low- and High-Band Transmit Mixer RF Input ConfigurationLow-Band Transmit Performance Parameters Low-Band Transmit Mixer Power Conversion GainLow-Band Transmit Mixer Test Guide Low-Band Transmit Mixer Noise Figure Low-Band Transmit Mixer Input Return Loss Low-Band Transmit Mixer Power Leakage TX In to LO Low-Band Transmit Mixer Power Leakage LO In to TXLow-Band Transmit Mixer 1dB Input Compression Point See Appendix a Test Bench Setups See Appendix a Test Bench Setups High-Band Transmit Mixer Performance Parameters High-Band Transmit Mixer Test GuideLow-Band LNA Gain Low-Band LNA Stand-Alone Test GuideLow-Band LNA Input Return Loss Low-Band LNA ParametersLow-Band LNA 1dB Input Compression Point Low-Band LNA Output Return LossLow-Band LNA Isolation Low-Band LNA Noise Figure Low-Band LNA Third Order Input Intercept Point IIP3 TRF1500 Integrated Dual-Band RF Receiver User’s Guide Low-Band Receiver Mixer Parameters Low-Band Receiver Mixer Power Conversion GainLow-Band Receiver Mixer Stand-Alone Test Guide Low-Band Receiver Mixer Input Return Loss Low-Band Receiver Mixer Noise Figure Low-Band Receiver Mixer Power Leakage LO In to RFTRF1500 Integrated Dual-Band RF Receiver User’s Guide Low-Band Receiver Mixer 1dB RF Input Compression Point 12.2 11.4 10.4 ←1dB Compression Point TRF1500 Integrated Dual-Band RF Receiver User’s Guide Appendix a Test Bench Configuration Test Bench Setup Noise Figure Test Bench Setup Power Leakage RF In to LO In Measurements Test Bench Setup LNA 1dB Input Compression Point