Hearth and Home Technologies HRV200PLUS manual HRV Plus Exhaust Guidelines

Page 15

HRV200PLUS INSTALLATION INSTRUCTIONS

4.HRV Exhaust - Stale air/combustion products from the HRV to the Flue Exhaust

Duct Materials: CoolVent™ Flexible Pipe - Zero Clearance to Combustible Materials

Horizontal Terminations: CoolVent™ Termination Cap

Vertical Terminations:

CoolVent™ Universal Adapter

 

B-Vent Roof Support

 

B-Vent Pipe Sections

 

B-Vent Termination Cap

a.HRV Plus Exhaust Guidelines

1)HRV must be vented with CoolVent™ flexible insulated vent pipe. The CoolVent™ flexible pipe can be installed with zero clearance to combustible materials when used as the HRV Exhaust.

2)The total combined length of the CoolVent™ vent run for the Fresh Air Fireplace Exhaust the HRV Exhaust must not exceed the maximum lengths in the following table:

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿ ￿￿￿￿ ￿

WARNING!

The maximum TOTAL EXHAUST vent run is measured from the flue collar of the Fresh Air Fire- place, through the HRV, to the outside termination. DO NOT EXCEED MAXIMUM VENTING LENGTHS!

3)Direction of flow may include any combination horizontal, vertical up or vertical down, but must not form a trap for condensation to collect.

4)Refer to Figures 7-9 for horizontal termination locations. b. Assembling the Vent Pipe Sections

1)When it is necessary to connect two or more lengths of CoolVent™ insulated flexible pipe in a vent run, use a universal connector at each joint.

2)Always support CoolVent™ insulated flexible pipe every three feet.

WARNING!

When vent pipe sections exceed three feet (.9m) in length, structural support must be provided to reduce off-center loading and insure minimum clearances are maintained. Follow manufacturer’s installation instructions.

02/04

4034-102 Rev F

15

Image 15
Contents Heat Recovery Ventilator Installation & Operating InstructionsHRV200PLUS Application Table of ContentsEngineering Data HRV200PLUS Clearance to Combustibles Appliance DimensionsDefrost Options Choose the defrost method best for your applicationNo Defrost Fresh Air Fireplace Defrost Setup for Room Air Defrost OptionSetup for Fresh Air Fireplace Defrost Option Room Air DefrostSimplified Installation Supply/Return Method Installation DiagramsPartially Dedicated Installation Exhaust AirFresh Air Fully Dedicated Installation Electrical Installing the VentilatorInstalling the Drain Line and P-Trap LocationLocate the Fresh Air Inlet Vent and Duct InstallationOptional Alternate Exhaust Damper Assembly StandardDuct the Warmside Air Supply Install Fresh Air Supply DuctingDampers and Grilles Warmside Ducting GuidelinesAssembling the Vent Pipe Sections HRV Plus Exhaust Guidelines Alternate Exhaust Port Exhaust TerminationStale Air from the Living Area to the HRV Alternate Exhaust Horizontal Exhaust Terminations see FiguresTypical Horizontal Termination Horizontal TerminationTermination Cap Locations As specified in CGA B149 Installation Codes Dimension DescriptionsTypical Vertical Termination see Figure Vertical Termination see FigureTypical Vertical Termination Vent Height Chase/Termination InstallationInstalling the Firestop Spacer Firestop Spacer/Vent InstallationNet Air Flow sCFM Selecting Blower SpeedsBalancing Balancing Collar InstructionsAir Flow Balancing Pitot Tube Balancing Procedure see Figure Pitot Tube Balancing Flow Station Balancing Flow Station Balancing Procedure see FigureOperating Modes Fireplace Operating Modes Connector P9OFF Mode Fireplace High Fire ModeHRV Defrost Mode Termination∅ d. Novus Plus/6000 Plus Initiation Thermostat Operating Modes Connector P6 Thermostat on ModeFireplace Control Terminals Ventilation Control Terminals Connector P1 Ventilation Operating Modes Connector P1Furnace Interface Operating Modes Connector P3 Interlock ModeFurnace Interface Terminals Wiring Fireplace Control Wiring∅ Caliber NXT Plus or 6100 Plus & HRV Wired Together ∅ Novus Plus Control Wiring ∅ 6000 Plus Control Wiring Thermostat Control Wiring Hvac System Thermostat Control WiringVentilation Control Wiring Ventilation Control WiringFurnace Interface Wiring Furnace Interface WiringSemi Annual Maintenance Clean Core Maintenance InstructionsMonthly Maintenance Inspect Exterior Hoods Quarterly MaintenanceInspect and Clean Duct Work if required Annual MaintenanceGeneral Maintenance Inspect and Clean Drain condensate Lines if requiredSummarized Guide 20+3 77.58!$% Installing Remote Controls AccessoriesREPLACEMENT-#$###$+*#!,&#PARTS#$% AHR IndexHRV200PLUS GAS Appliance Limited Warranty

HRV200PLUS specifications

The Hearth and Home Technologies HRV200PLUS is an advanced heat recovery ventilator (HRV) designed to provide optimal indoor air quality while ensuring energy efficiency. As homes become increasingly airtight due to modern construction techniques, the importance of proper ventilation grows. The HRV200PLUS addresses this need by continuously exchanging stale indoor air with fresh outdoor air, effectively maintaining a healthy living environment.

One of the standout features of the HRV200PLUS is its innovative heat recovery technology. This system captures the heat from the outgoing air and transfers it to the incoming fresh air. As a result, the air being brought into the home is pre-warmed, reducing the demand on heating systems during the colder months. This energy-efficient method helps homeowners save on heating costs while maintaining comfort levels inside the home.

Another notable characteristic of the HRV200PLUS is its quiet operation. Equipped with high-performance, low-noise fans, this unit operates in silence, ensuring that occupants can enjoy a peaceful environment without the disruptive sounds often associated with ventilation systems. Additionally, the HRV200PLUS provides versatile installation options, allowing it to be easily integrated into both new and existing homes.

The unit features adjustable settings that allow users to customize airflow according to their specific needs. With multiple fan speeds, homeowners can choose the most suitable option for their daily activities, ensuring an ideal balance between indoor air quality and energy use. Furthermore, the HRV200PLUS includes a built-in filter system that captures dust, allergens, and other airborne particles, enhancing overall air quality.

Durability and ease of maintenance are also keys in the design of the HRV200PLUS. Constructed with high-quality materials, this unit is made to last, reducing the need for frequent replacements. The filters are easily accessible, making periodic maintenance straightforward, which further extends the product's lifespan.

In summary, the Hearth and Home Technologies HRV200PLUS stands out as a premium choice for homeowners seeking a reliable and efficient ventilation solution. Its combination of heat recovery technology, quiet operation, customizable settings, and easy maintenance make it an ideal option for improving indoor air quality while keeping energy costs in check. As the emphasis on healthy living spaces continues to grow, the HRV200PLUS remains a practical investment for modern homes.